UNI EN ISO 15138 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - OFFSHORE PRODUCTION INSTALLATIONS - HEATING, VENTILATION AND AIR-CONDITIONING
29-08-2018
01-01-2008
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 Design
5.1 Introduction
5.2 Development of design basis
5.3 System design - General
5.4 Area-specific system design
5.5 Equipment and bulk selection
5.6 Installation and commissioning
Annex A (normative) - Equipment and bulk selection
Annex B (normative) - Installation and commissioning
Annex C (informative) - Operation and maintenance
Annex D (informative) - Datasheets
Annex E (normative) - Standard data for flanges
Bibliography
Describes requirements and provides guidance for design, testing, installation and commissioning of heating, ventilation, air-conditioning and pressurization systems and equipment on all offshore production installations for the petroleum and natural gas industries that are: - new or existing, - normally occupied by personnel or not normally occupied by personnel, - fixed or floating but registered as an offshore production installation.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 15138:2008-07 | Identical |
| NS EN ISO 15138 : 2ED 2007 | Identical |
| I.S. EN ISO 15138:2007 | Identical |
| BS EN ISO 15138:2007 | Identical |
| NF EN ISO 15138 : 2009 | Identical |
| ONORM EN ISO 15138 : 2008 | Identical |
| ISO 15138:2007 | Identical |
| SN EN ISO 15138 : 2008 | Identical |
| NBN EN ISO 15138 : 2008 | Identical |
| EN ISO 15138:2007 | Identical |
| NEN EN ISO 15138 : 2008 | Identical |
| ISO 12499:1999 | Industrial fans Mechanical safety of fans Guarding |
| IEC 60079-10:2002 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
| EN 1886:2007 | Ventilation for buildings - Air handling units - Mechanical performance |
| EN 1507:2006 | Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strength and leakage |
| EN 13053:2006+A1:2011 | Ventilation for buildings - Air handling units - Rating and performance for units, components and sections |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 1505:1997 | Ventilation for buildings - Sheet metal air ducts and fittings with rectangular cross section - Dimensions |
| NS 5575 : 1ED 1987 | VENTILATION DUCTS - IDENTIFICATION COLOURS |
| NFPA 96 : 2017 | VENTILATION CONTROL AND FIRE PROTECTION OF COMMERCIAL COOKING OPERATIONS |
| EN 378-4:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery |
| ISO 14694:2003 | Industrial fans — Specifications for balance quality and vibration levels |
| EN 378-1:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria |
| EN 378-3:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection |
| ISO 7547:2002 | Ships and marine technology Air-conditioning and ventilation of accommodation spaces Design conditions and basis of calculations |
| ISO 16812:2007 | Petroleum, petrochemical and natural gas industries Shell-and-tube heat exchangers |
| ISO 5149:1993 | Mechanical refrigerating systems used for cooling and heating Safety requirements |
| ISO 9309:1989 | Refrigerant compressors Presentation of performance data |
| ISO 8861:1998 | Shipbuilding — Engine-room ventilation in diesel-engined ships — Design requirements and basis of calculations |
| ISO 1940-1:2003 | Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances |
| ISO 917:1989 | Testing of refrigerant compressors |
| EN 779:2012 | Particulate air filters for general ventilation - Determination of the filtration performance |
| ASHRAE HDBK FUNDAMENTALS : 2013 | ASHRAE HANDBOOK - FUNDAMENTALS |
| EN 1506:2007 | Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions |
| AMCA 210 : 2016 | LABORATORY METHODS OF TESTING FANS FOR CERTIFIED AERODYNAMIC PERFORMANCE RATING |
| ISO 5801:2017 | Fans — Performance testing using standardized airways |
| EN 12237:2003 | Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts |
| API 505 : 1997 | RECOMMENDED PRACTICE FOR CLASSIFICATION OF LOCATIONS FOR ELECTRICAL INSTALLATIONS AT PETROLEUM FACILITIES CLASSIFIED AS CLASS I, ZONE 0, ZONE 1, AND ZONE 2 |
| AMCA 500 D : 2012 | LABORATORY METHODS OF TESTING DAMPERS FOR RATING |
| ISO 12241:2008 | Thermal insulation for building equipment and industrial installations Calculation rules |
| EN 50272-2:2001 | Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| ISO 7730:2005 | Ergonomics of the thermal environment — Analytical determination and interpretation of thermal comfort using calculation of the PMV and PPD indices and local thermal comfort criteria |
| IP 15 : 2015 | PETROLEUM PRODUCTS - DETERMINATION OF POUR POINT |
| EN 1751:2014 | Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves |
| ISO 7235:2003 | Acoustics — Laboratory measurement procedures for ducted silencers and air-terminal units — Insertion loss, flow noise and total pressure loss |
| API 4589 : 1993 | Fugitive Hydrocarbon Emissions from Oil and Gas Production Operations |
| ISO 13702:2015 | Petroleum and natural gas industries — Control and mitigation of fires and explosions on offshore production installations — Requirements and guidelines |
| EN 378-2:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation |
| EN 12451:2012 | Copper and copper alloys - Seamless, round tubes for heat exchangers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.