API 672 : 2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PACKAGED, INTEGRALLY GEARED CENTRIFUGAL AIR COMPRESSORS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
Hardcopy , PDF
27-08-2019
English
01-01-2004
Important note : Users cannot be edited or removed once added to your Multi user PDF.
0 INTRODUCTION
1 SCOPE
2 NORMATIVE REFERENCES
3 DEFINITION OF TERMS
4 GENERAL
4.1 Unit Responsibility
4.2 Nomenclature
5 REQUIREMENTS
5.1 Units of Measurement
5.2 Statutory Requirements
5.3 Alternative Designs
5.4 Conflicting Requirements
6 BASIC DESIGN
6.1 General
6.2 Pressure Casings
6.3 Casing Connections
6.4 External Forces and Moments
6.5 Rotating Elements
6.6 Seals and Sealing Systems
6.7 Dynamics
6.8 Bearings and Bearings Housings
6.9 Lubrication
6.10 Materials
6.11 Nameplates and Rotation Arrows
6.12 Additional Requirements for Special Duty Packages
7 ACCESSORIES
7.1 Drivers
7.2 Couplings and Guards
7.3 Baseplate/Support Structure
7.4 Controls and Instrumentation
7.5 Piping
7.6 Intercoolers and Aftercoolers
7.7 Inlet Air Filter/Silencer
7.8 Discharge Blowoff Silence
7.9 Special Tools
7.10 Additional Requirements for "Special Duty" packages
8 INSPECTION, TESTING AND PREPARATION FOR SHIPMENT
8.1 General
8.2 Inspection
8.3 Testing
8.4 Preparation for Shipment
8.5 Additional Inspection, Testing & Preparation for Shipment
Requirements for "Special Duty" Packages
9 VENDOR DATA
9.1 General
9.2 Proposals
9.3 Contract Data
9.4 Additional Vendor Data Requirements for "Special Duty"
Packages
ANNEX A DATA SHEETS
ANNEX B REFERENCED DOCUMENTS
ANNEX C (INFORMATION ON ROTORDYNAMIC ANALYSIS)
ANNEX D VENDOR DRAWINGS AND DATA REQUIREMENTS
ANNEX E LUBRICATION SYSTEM SCHEMATIC
ANNEX F REQUIREMENTS FOR DETERMINING RESIDUAL UNBALANCE
ANNEX G INSPECTOR'S CHECKLIST
ANNEX H GUIDE TO NOMENCLATURE
Specifies minimum requirements for constant speed, packaged, general purpose integrally geared centrifugal air compressors including their accessories. Does not apply to machines which develop a pressure rise of less than 0.35 BAR (5.0 psi) above atmospheric pressure, classed as fans or blowers.
| DocumentType |
Standard
|
| Pages |
137
|
| PublisherName |
American Petroleum Institute
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| 10/30231432 DC : 0 | BS EN ISO 10439-1 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS - PART 1: GENERAL REQUIREMENTS |
| API 9100B : 1998 | GUIDANCE DOCUMENT FOR MODEL EHS MANAGEMENT SYSTEM |
| BS EN ISO 10439-1:2015 | Petroleum, petrochemical and natural gas industries. Axial and centrifugal compressors and expander-compressors General requirements |
| BS EN ISO 10442:2002 | Petroleum, chemical and gas service industries. Packaged, integrally geared centrifugal air compressors |
| BS EN ISO 10438-3:2003 | Petroleum, petrochemical and natural gas industries. Lubrication, shaft sealing and control oil systems and auxilliaries General-purpose oil systems |
| I.S. EN ISO 10439-3:2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS - PART 3: INTEGRALLY GEARED CENTRIFUGAL COMPRESSORS (ISO 10439-3:2015) |
| BS EN ISO 10439-3:2015 | Petroleum, petrochemical and natural gas industries. Axial and centrifugal compressors and expander-compressors Integrally geared centrifugal compressors |
| I.S. EN ISO 10439-2:2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS - PART 2: NON-INTEGRALLY GEARED CENTRIFUGAL AND AXIAL COMPRESSORS (ISO 10439-2:2015) |
| I.S. EN ISO 10438-3:2007 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - LUBRICATION, SHAFT-SEALING AND CONTROL-OIL SYSTEMS AND AUXILIARIES - PART 3: GENERAL-PURPOSE OIL SYSTEMS |
| 10/30231440 DC : 0 | BS EN ISO 10439-3 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS - PART 3: INTEGRALLY GEARED CENTRIFUGAL COMPRESSORS |
| API 613:2003 | SPECIAL PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES |
| I.S. EN ISO 10439-1:2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS - PART 1: GENERAL REQUIREMENTS (ISO 10439-1:2015) |
| API 614 REDLINE : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
| UNI EN ISO 10438-3 : 2009 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - LUBRICATION, SHAFT-SEALING AND CONTROL-OIL SYSTEMS AND AUXILIARIES - PART 3: GENERAL-PURPOSE OIL SYSTEMS |
| ISO 10442:2002 | Petroleum, chemical and gas service industries Packaged, integrally geared centrifugal air compressors |
| ISO 10439-1:2015 | Petroleum, petrochemical and natural gas industries Axial and centrifugal compressors and expander-compressors Part 1: General requirements |
| ISO 10438-3:2007 | Petroleum, petrochemical and natural gas industries Lubrication, shaft-sealing and control-oil systems and auxiliaries Part 3: General-purpose oil systems |
| EN ISO 10438-3:2007 | Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2007) |
| EN ISO 10439-3:2015 | Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 3: Integrally geared centrifugal compressors (ISO 10439-3:2015) |
| EN ISO 10439-2:2015 | Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 2: Non-integrally geared centrifugal and axial compressors (ISO 10439-2:2015) |
| EN ISO 10439-1:2015 | Petroleum, petrochemical and natural gas industries - Axial and centrifugal compressors and expander-compressors - Part 1: General requirements (ISO 10439-1:2015) |
| EN ISO 10442:2002 | Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002) |
| BS EN ISO 10439-2:2015 | Petroleum, petrochemical and natural gas industries. Axial and centrifugal compressors and expander-compressors Non-integrally geared centrifugal and axial compressors |
| API 614 : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
| ISO 10439-2:2015 | Petroleum, petrochemical and natural gas industries Axial and centrifugal compressors and expander-compressors Part 2: Non-integrally geared centrifugal and axial compressors |
| ISO 10439-3:2015 | Petroleum, petrochemical and natural gas industries Axial and centrifugal compressors and expander-compressors Part 3: Integrally geared centrifugal compressors |
| PIP PCEIA001 : 2016 | INSTRUMENT AIR SYSTEMS GUIDELINES |
| PIP REEC001 : 2013 | COMPRESSOR SELECTION GUIDELINES |
| AGMA 9002 : B | BORES AND KEYWAYS FOR FLEXIBLE COUPLINGS (INCH SERIES) |
| AGMA 6011 : I | SPECIFICATION FOR HIGH SPEED HELICAL GEAR UNITS |
| ASTM E 446 : 2015 : REDLINE | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ASTM E 186 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings |
| NEMA SM 23-1991 (R1997, R2002) | STEAM TURBINES FOR MECHANICAL DRIVE SERVICE |
| API 546 : 2008 | BRUSHLESS SYNCHRONOUS MACHINES - 500 KVA AND LARGER |
| IEEE 841-2009 | IEEE Standard for Petroleum and Chemical Industry--Premium-Efficiency, Severe-Duty, Totally Enclosed Fan-Cooled (TEFC) Squirrel Cage Induction Motors--Up to and Including 370 kW (500 hp) |
| ASTM A 395/A395M : 1999 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
| ISO 1328-1:2013 | Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth |
| ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
| API 614 : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
| ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
| NEMA 250 : 2014 | ENCLOSURES FOR ELECTRICAL EQUIPMENT (1000 VOLTS MAXIMUM) |
| ASME B16.42 : 2016 | DUCTILE IRON PIPE FLANGES AND FLANGED FITTINGS - CLASSES 150 AND 300 |
| ISO 10436:1993 | Petroleum and natural gas industries — General-purpose steam turbines for refinery service |
| NFPA 496 : 2017 | PURGED AND PRESSURIZED ENCLOSURES FOR ELECTRICAL EQUIPMENT |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| ISO 10438-3:2007 | Petroleum, petrochemical and natural gas industries Lubrication, shaft-sealing and control-oil systems and auxiliaries Part 3: General-purpose oil systems |
| ISO 5389:2005 | Turbocompressors — Performance test code |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| API 670 : 2014 | MACHINERY PROTECTION SYSTEMS |
| ISO 8821:1989 | Mechanical vibration Balancing Shaft and fitment key convention |
| API 617 : 2014 | AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS |
| ISO/R 773:1969 | Rectangular or square parallel keys and their corresponding keyways (Dimensions in millimetres) |
| NFPA NEC ANALYSIS OF CHANGES : 2017 | NEC ANALYSIS OF CHANGES |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ISO 10438-1:2007 | Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 1: General requirements |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| API STD 541 : 2014 | FORM-WOUND SQUIRREL CAGE INDUCTION MOTORS - 375 KW (500 HORSEPOWER) AND LARGER |
| MSS SP 55 : 2011 | QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| AWS D1.1/D1.1M : 2015 | STRUCTURAL WELDING CODE-STEEL |
| ASTM A 515/A515M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service |
| ASME B16.47 : 2017 | LARGE DIAMETER STEEL FLANGES: NPS 26 THROUGH NPS 60 METRIC/INCH STANDARD |
| ASTM A 275/A275M : 2015-05 | PRACTICE FOR MAGNETIC PARTICLE EXAMINATION OF STEEL FORGINGS |
| ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.