ASME PV CODE 1 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF POWER BOILERS
Hardcopy
01-07-2019
English
01-07-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.
List of Sections
Foreword
Statement of Policy on the Use of the Certification Mark and Code
Authorization in Advertising
Statement of Policy on the Use of ASME Marking to Identify
Manufactured Items
Submittal of Technical Inquiries to the Boiler and Pressure
Vessel Standards Committees
Personnel
Preamble
Summary of Changes
List of Changes in Record Number Order
Cross-Referencing and Stylistic Changes in the Boiler and
Pressure Vessel Code
Part PG - General Requirements for all Methods of Construction
Part PW - Requirements for Boilers Fabricated by Welding
Part PR - Requirements for Boilers Fabricated by Riveting
Part PB - Requirements for Boilers Fabricated by Brazing
Part PL - Requirements for Locomotive Boilers
Part PA - Alternative Rules for Boiler Construction
Part PWT - Requirements for Watertube Boilers
Part PFT - Requirements for Firetube Boilers
Part PFH - Optional Requirements for Feedwater Heater (When
Located Within Scope of Section I Rules)
Part PMB - Requirements for Miniature Boilers
Part PEB - Requirements for Electric Boilers
Part PVG - Requirements for Organic Fluid Vaporizers
Part PFE - Requirements for Feedwater Economizers
Part PTFH - Requirements for Liquid Phase Thermal Fluid Heaters
Part PHRSG - Requirements for Heat Recovery Steam Generators
Mandatory Appendix II - Standard Units for Use in Equations
Mandatory Appendix III - Criteria for Reapplication of a
Certification Mark
Mandatory Appendix IV - Local Thin Areas in Cylindrical Shells and
in Spherical Segments of Heads
Mandatory Appendix V - Additional Rules for Boilers Fabricated
by Riveting
Mandatory Appendix VI - Establishing Governing Code Editions,
Addenda, and Cases for Boilers and
Replacement Parts
Nonmandatory Appendix A - Explanation of the Code Containing
Matter Not Mandatory Unless Specifically
Referred to in the Rules of the Code
Nonmandatory Appendix B - Positive Material Identification Practice
Nonmandatory Appendix C - Local Heating of Welds in Cylindrical
Components of P-No. 15E Materials When Using
Electric Resistance Heating
Nonmandatory Appendix D - Design Guidelines for Corrosion, Erosion,
and Steam Oxidation of Boiler Tubes
Nonmandatory Appendix E - Alternative Method for Ultrasonic
Examination
Provides mandatory requirements, specific prohibitions, and nonmandatory guidance for construction activities and inservice inspection and testing activities.
| DocumentType |
Standard
|
| Pages |
429
|
| PublisherName |
American Society of Mechanical Engineers
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| MIL-B-18897 Revision F:1990 | BOILERS, STEAM AND HOT WATER, WATERTUBE (STRAIGHT BARE AND FINNED TUBE), CAST IRON AND FIREBOX, PACKAGED TYPE (40,000 TO 35,000 BTU/HR THERMAL OUTPUT CAPACITY) |
| ASCE 7 10 : 2011 | MINIMUM DESIGN LOADS FOR BUILDINGS AND OTHER STRUCTURES |
| UFC 3-430-02FA : Change 1 | UNIFIED FACILITIES CRITERIA - CENTRAL STEAM BOILER PLANTS |
| MIL-B-17452 Revision E:1990 | BOILERS, STEAM AND HOT WATER, FIRETUBE - SCOTCH PACKAGED TYPE (320,001 TO 35,000,000 BTU/HR THERMAL OUTPUT CAPACITY) |
| MIL-B-16907 Revision G:1988 | BOILER, STEAM, HIGH PRESSURE, AUXILIARY FIRE TUBE TYPE, NAVAL SHIPBOARD |
| API 538 : 2015 | INDUSTRIAL FIRED BOILERS FOR GENERAL REFINERY AND PETROCHEMICAL SERVICE |
| API 573 : 2013 | INSPECTION OF FIRED BOILERS AND HEATERS |
| MIL B 18381 : D | BOILER, STEAM, HIGH PRESSURE, NAVAL SHIP PROPULSION |
| MIL-B-23170 Revision A:1978 | BOILERS, STEAM, HIGH PRESSURE WATER TUBE, PACKAGED TYPE (5,000 TO 50,000 POUNDS PER HOUR, FIRED BY COAL, OIL, GAS OR COMBINATION OIL/GAS) |
| API 579-1 : 2016 | FITNESS-FOR-SERVICE |
| EEMUA 193 : 2013 | MANAGING COMPETENCE ASSURANCE FOR PERSONNEL UNDERTAKING IN-SERVICE INSPECTION OF PRESSURE EQUIPMENT |
| ASME B16.34 : 2017 | VALVES - FLANGED, THREADED, AND WELDING END |
| MSS SP 25 : 2013 | STANDARD MARKING SYSTEM FOR VALVES, FITTINGS, FLANGES, AND UNIONS |
| API 582 : 2016 | WELDING GUIDELINES FOR THE CHEMICAL, OIL, AND GAS INDUSTRIES |
| API 936 : 2014 | REFRACTORY INSTALLATION QUALITY CONTROL - INSPECTION AND TESTING MONOLITHIC REFRACTORY LININGS AND MATERIALS |
| API 534 : 2007 : R2013 | HEAT RECOVERY STEAM GENERATORS |
| AWS B5.15 : 2010 | SPECIFICATION FOR THE QUALIFICATION OF RADIOGRAPHIC INTERPRETERS |
| MIL-B-29205 Revision A:1990 | BOILERS, FLUIDIZED BED, STEAM AND HOT WATER, PACKAGED TYPE (330 TO 51,500 POUNDS PER HOUR THERMAL OUTPUT CAPACITY) |
| MIL-B-28684 Base Document:1990 | BOILERS, STEAM AND HOT WATER, VERTICAL FIRETUBE AND VERTICAL TUBELESS, PACKAGED TYPE (40,000 TO 10,000,000 BTU/HR THERMAL OUTPUT CAPACITY) |
| MSS SP 80 : 2013 | BRONZE GATE, GLOBE, ANGLE, AND CHECK VALVES |
| AWS C5.7 : 2000 | RECOMMENDED PRACTICES FOR ELECTROGAS WELDING |
| AWS B5.4 : 2005 | SPECIFICATION FOR THE QUALIFICATION OF WELDER TEST FACILITIES |
| API 551 : 2016 | PROCESS MEASUREMENT |
| API 534 : 2007 | HEAT RECOVERY STEAM GENERATORS |
| GG-S-1340 Revision A:1975 | STERILIZER, SURGICAL INSTRUMENT AND SUPPLY GRAVITY AIR REMOVAL, NONPORTABLE (HEAT AND MOISTURE STABLE) |
| ASME PTB 2 : 2009 | GUIDE TO LIFE CYCLE MANAGEMENT OF PRESSURE EQUIPMENT INTEGRITY |
| PIP VECV1001 : 2017 | DESIGN CRITERIA AND PURCHASING REQUIREMENTS FOR VESSELS ASME CODE SECTION 8, DIVISIONS 1 AND 2 |
| ASME FFS 1 : 2007 | FITNESS-FOR-SERVICE |
| API 576 CHINESE : 2009 | INSPECTION OF PRESSURE-RELIEVING DEVICES |
| EEMUA 184 : 2009 | GUIDE TO THE ISOLATION OF PRESSURE RELIEVING DEVICES |
| MIL-B-17095 Revision H:1990 | BOILERS, STEAM, WATERTUBE (BENT TUBE, MULTI-DRUM AND CROSS DRUM) PACKAGED TYPE (10,000,000 TO 125,000,000 BTU/HR THERMAL OUTPUT CAPACITY) |
| API 520-1 : 2014 | SIZING, SELECTION, AND INSTALLATION OF PRESSURE-RELIEVING DEVICES - PART 1: SIZING AND SELECTION |
| MIL-B-17228 Revision F:1990 | BOILERS, STEAM AND HOT WATER, WATERTUBE (COIL AND SERPENTINE), PACKAGED TYPE (40,000 TO 10,000,000 BTU/HR THERMAL OUTPUT CAPACITY) |
| CSA B51 : 2014 | BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASTM E 1344 : 1990 : R2006 | Standard Guide for Evaluation of Fuel Ethanol Manufacturing Facilities (Withdrawn 2009) |
| ASME PV CODE 7 : 2017 | BPVC Section VII-BOILER AND PRESSURE VESSEL CODE - RECOMMENDED GUIDELINES FOR THE CARE OF POWER BOILERS |
| ASTM E 1117 : 1997 : R2006 | Standard Practice for Design of Fuel-Alcohol Manufacturing Facilities (Withdrawn 2009) |
| ASTM A 1091/A1091M : 2016 | Standard Specification for Steel Castings, Creep-Strength Enhanced Ferritic Alloy, for Pressure-Containing Parts, Suitable for High Temperature Service |
| ASTM A 1091/A1091M : 2016 : EDT 1 | Standard Specification for Steel Castings, Creep-Strength Enhanced Ferritic Alloy, for Pressure-Containing Parts, Suitable for High Temperature Service |
| ASTM E 1117 : 1997 | Standard Practice for Design of Fuel-Alcohol Manufacturing Facilities |
| NASA-STD-8719.17C:2017 | NASA REQUIREMENTS FOR GROUND-BASED PRESSURE VESSELS AND PRESSURIZED SYSTEMS (PVS) |
| ASTM E 1344 : 1990 : R1997 : EDT 1 | Standard Guide for Evaluation of Fuel Ethanol Manufacturing Facilities |
| UFC 3-430-11 : 2001 | UNIFIED FACILITIES CRITERIA - BOILER CONTROL SYSTEMS |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| Z276-18 | Liquefied natural gas (LNG) - Production, storage, and handling |
| ASTM F 1323 : 2014 : REDLINE | Standard Specification for Shipboard Incinerators |
| MSS SP 67 : 2017 | BUTTERFLY VALVES |
| PIP PCSPS010 : 2008 | SMALL, GENERAL PURPOSE PACKAGED EQUIPMENT INSTRUMENTATION SPECIFICATION |
| PIP PCCLI001 : 2014 | LEVEL MEASUREMENT DESIGN CRITERIA |
| API 576 REDLINE : 2009 | INSPECTION OF PRESSURE-RELIEVING DEVICES |
| ASME PTB 11 : 2017 | GUIDE FOR ASME BPVC SECTION 1 STAMP HOLDERS |
| PIP PCELI001 : 2014 | LEVEL MEASUREMENT GUIDELINES |
| ASME PTB 8 : 2014 | Procurement Guidelines for Metallic Materials (PTB-8 - 2014) |
| PIP PCSPS010 : 2008 : R2013 | SMALL, GENERAL PURPOSE PACKAGED EQUIPMENT INSTRUMENTATION SPECIFICATION |
| ASME STP-PT-086 : 2017 | EFFECTS OF HIGH TEMPERATURES AND FIT-UP OF RIVETED JOINTS ON STEEL RIVETS |
| API GIRE CH16 : 3ED 85 | PRESSURE RELIEVING DEVICES |
| ASME STP-PT-002 : 2005 | ASME SECTION 1 PED GUIDE - SUPPLEMENT TO GUIDE FOR ASME STAMP HOLDERS USE OF ASME SECTION 1 TO MEET THE EC PRESSURE EQUIPMENT DIRECTIVE (97/23/EC) |
| MSS SP 84 : 1990 | STEEL VALVES-SOCKET WELDING AND THREADED ENDS |
| ASME STP-PT-070 : 2014 | Design Guidelines for the Effects of Creep, Fatigue & Creep-Fatigue Interaction with Design-By-Analysis and Nondestructive Inspection Acceptance Criteria (STP-PT-070 - 2014) |
| PIP PCSPS001 : 2015 | PACKAGED EQUIPMENT INSTRUMENTATION SPECIFICATION |
| CFR 49(PTS 200-299) : OCT 2017 | TRANSPORTATION |
| ASTM E 446 : 2015 : REDLINE | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
| ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| ASTM E 186 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings |
| ASME B31.1 : 2016 | POWER PIPING |
| ASME PTC25 : 2014 | PRESSURE RELIEF DEVICES |
| ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
| ASME B16.42 : 2016 | DUCTILE IRON PIPE FLANGES AND FLANGED FITTINGS - CLASSES 150 AND 300 |
| ASME B16.15 : 2013 | CAST COPPER ALLOY THREADED FITTINGS: CLASSES 125 AND 250 |
| ASME B16.20 : 2012 | METALLIC GASKETS FOR PIPE FLANGES |
| ASTM E 9 : 2009 | Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ASME CA 1 : 2014 | CONFORMITY ASSESSMENT REQUIREMENTS |
| ASNT CP 189 : 2016 | QUALIFICATION AND CERTIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| ASME QAI 1 : 2010 | QUALIFICATIONS FOR AUTHORIZED INSPECTION |
| ASME B36.10M : 2015 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| ASTM E 125 : 1963 : R2003 | Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME B16.34 : 2017 | VALVES - FLANGED, THREADED, AND WELDING END |
| ASTM E 280 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings |
| ASME B16.4 : 2016 | GRAY IRON THREADED FITTINGS: CLASSES 125 AND 250 |
| ASME B16.9 : 2012 | FACTORY-MADE WROUGHT BUTTWELDING FITTINGS |
| ASME B16.47 : 2017 | LARGE DIAMETER STEEL FLANGES: NPS 26 THROUGH NPS 60 METRIC/INCH STANDARD |
| ASME B16.25 : 2012 | BUTTWELDING ENDS |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
| ASME B16.3 : 2016 | MALLEABLE IRON THREADED FITTINGS: CLASSES 150 AND 300 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.