ASTM A 449 : 2014 : REDLINE
Current
The latest, up-to-date edition.
Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
English
01-10-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 01.08, 2017 Defines quenched and tempered steel hex cap screws, bolts, and studs having a minimum tensile strength of 120 ksi for diameters 1.0 in. and smaller; 105 ksi for diameters over 1.0 in. to 1[1/2] in.; and 90 ksi for diameters 1[3/4] in. to 3.0 in. inclusive.
| Committee |
F 16
|
| DocumentType |
Redline
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1This specification2 covers quenched and tempered steel hex cap screws, bolts, and studs having a minimum tensile strength of 120 ksi for diameters 1.0 in. and smaller; 105 ksi for diameters over 1.0 in. to 11/2in.; and 90 ksi for diameters 13/4in. to 3.0 in. inclusive. The term "fasteners" in this specification denotes hex cap screws, bolts, and studs.
1.2The fasteners are intended for general engineering use.
1.3The fasteners are furnished in diameters 1/4to 3.0 in. inclusive. They are designated by type denoting chemical composition as follows:
| Type | Description |
| Type I | Plain carbon steel, carbon boron steel, alloy steel, or alloy boron steel |
| Type 2 | Withdrawn 2003 |
| Type 3 | Weathering steel |
1.4Terms used in this specification are defined in Terminology F1789 unless otherwise defined in this specification.
1.5The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| C83-17 | COMMUNICATION AND POWER LINE HARDWARE |
| BS EN 61518:2001 | Mating dimensions between differential pressure (type) measuring instruments and flanged-on shut-off devices up to 413 bar (41,3 MPa) |
| AISC 350 : 99 ERRATA 2001 | LOAD AND RESISTANCE FACTOR DESIGN SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS |
| ASTM A 760/A760M : 2015 : REDLINE | Standard Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains |
| ASTM F 1718 : 2001 : R2019 | Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps |
| ASTM F 1718 : 2001 : R2013 | Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps |
| BS EN ISO 10442:2002 | Petroleum, chemical and gas service industries. Packaged, integrally geared centrifugal air compressors |
| MIL-DTL-1222 Revision J:2000 | STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR |
| MIL STD 11991 : A | GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES |
| DIN EN 61518:2002-06 | MATING DIMENSIONS BETWEEN DIFFERENTIAL PRESSURE (TYPE) MEASURING INSTRUMENTS AND FLANGED-ON SHUT-OFF DEVICES UP TO 413 BAR (41,3 MPA) |
| MIL-V-10386 Revision E:1977 | SWING, CAST-IRON AND STEEL |
| CSA S136-12 PACKAGE : 2012 | CONSISTS OF S136-12 - NORTH AMERICAN SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS AND S136.1-12 - COMMENTARY ON NORTH AMERICAN SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS |
| ASTM A 563 : 2015 : REDLINE | Standard Specification for Carbon and Alloy Steel Nuts |
| ASTM F 2437/F2437M : 2017 : REDLINE | Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs |
| IFI 124 : 2002 | TEST PROCEDURE FOR THE PERFORMANCE OF NONMETALLIC RESISTANT ELEMENT PREVAILING-TORQUE SCREWS |
| ASCE 48 05 : 2006 | DESIGN OF STEEL TRANSMISSION POLE STRUCTURES |
| IFI 160 : 2007 | TEST PROCEDURE FOR THE PERFORMANCE OF NUTS WITH PRE-APPLIED ADHESIVE COATED THREADS - INCH SERIES |
| ASTM F 2798 : 2009 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
| ASTM F 2798 : 2009 : R2014 : EDT 1 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
| ASTM A 762/A762M : 2015 : REDLINE | Standard Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and Drains |
| ASTM F 1510 : 2007 : R2013 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
| ASTM F 3125 : 2015 | Standard Specification for High Strength Structural Bolts, Steel and Alloy Steel, Heat Treated, 120 ksi (830 MPa) and 150 ksi (1040 MPa) Minimum Tensile Strength, Inch and Metric Dimensions |
| AWWA C541 : 2016 | HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES |
| ASME B31.1 : 2016 | POWER PIPING |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME B31.4 : 2016 | PIPELINE TRANSPORTATION SYSTEMS FOR LIQUIDS AND SLURRIES |
| ASME B31.8 : 2016 | Gas Transmission and Distribution Piping Systems |
| WW-P-405 Revision B:1974 | PIPE, CORRUGATED (IRON OR STEEL, ZINC COATED) |
| AWWA C606 : 2015 | GROOVED AND SHOULDERED JOINTS |
| MS51868 Revision E:2017 | CLAMP, WIRE ROPE, DOUBLE SADDLED, DOUBLE-GRIP, STEEL, TYPE 3 |
| ASTM F 2482 : 2008 | Standard Specification for Load-Indicating Externally Threaded Fasteners |
| IEEE 1630-2012 | IEEE Standard for Supporting Structures for Overhead Contact Systems for Transit Systems |
| ASTM F 1718 : 2001 | Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps |
| ASTM F 2482 : 2008 : R2015 | Standard Specification for Load-Indicating Externally Threaded Fasteners |
| ASTM F 1718 : 2001 : R2006 | Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps |
| EN 61518:2001/corrigendum:2002 | MATING DIMENSIONS BETWEEN DIFFERENTIAL PRESSURE (TYPE) MEASURING INSTRUMENTS AND FLANGED-ON SHUT-OFF DEVICES UP TO 413 BAR (41,3 MPA) |
| MIL-HDBK-454 Revision B:2007 | GENERAL GUIDELINES FOR ELECTRONIC EQUIPMENT |
| ASTM A 761/A761M : 2017-02 | SPECIFICATION FOR CORRUGATED STEEL STRUCTURAL PLATE, ZINC-COATED, FOR FIELD-BOLTED PIPE, PIPE-ARCHES, AND ARCHES |
| AISC 360 : 2016 | SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS |
| MIL-S-52881 Revision B:1989 | SERVICING UNITS, COMPRESSED GAS, MOBILE |
| ASTM F 1510 : 2007 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
| ISO 10442:2002 | Petroleum, chemical and gas service industries Packaged, integrally geared centrifugal air compressors |
| IEC 61518:2001 | Mating dimensions between differential pressure (type) measuring instruments and flanged-on shut-off devices up to 413 BAR (41,3 MPa) |
| EN ISO 10442:2002 | Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002) |
| ACI 355.3R : 2011 | GUIDE FOR DESIGN OF ANCHORAGE TO CONCRETE: EXAMPLES USING ACI 318 APPENDIX D |
| GGG-B-490 Revision F:1992 | BLOCKS, TACKLE (MANILA AND NYLON ROPE) |
| AISC 335 : 89 SUPP 1 1999 | SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS - ALLOWABLE STRESS DESIGN, PLASTIC DESIGN |
| MIL N 45913 : B | NUTS, SELF LOCKING, HEXAGON, PREVAILING-TORQUE |
| IFI 136 : 2006 | STUDS AND BENT BOLTS |
| MSS SP 101 : 2014 | PART-TURN VALVE ACTUATOR ATTACHMENT - FA FLANGE AND DRIVING COMPONENT DIMENSIONS AND PERFORMANCE CHARACTERISTICS |
| MIL-B-28536 Revision C:1989 | BUILDING, PREFABRICATED, READY CUT, METAL, RIGID FRAME, 40 X 100 FEET |
| IFI 124 : 2002 : R2013 | TEST PROCEDURE FOR THE PERFORMANCE OF NONMETALLIC RESISTANT ELEMENT PREVAILING-TORQUE SCREWS |
| AASHTO M 167M/M 167 : 2014 | SPECIFICATION FOR CORRUGATED STEEL STRUCTURAL PLATE, ZINC-COATED, FOR FIELD-BOLTED PIPE, PIPE-ARCHES, AND ARCHES |
| SAE J2295_201611 | Fastener Part Standard - Cap Screws, Hex, Heavy Hex and Heavy Hex Structural Bolts, and Hex Nuts (Inch Dimensioned) |
| MIL-STD-777 Revision F:2012 | SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS |
| CSA G401 : 2014 | CORRUGATED STEEL PIPE PRODUCTS |
| ASCE/SEI 48 11 : 2011 | DESIGN OF STEEL TRANSMISSION POLE STRUCTURES |
| ASTM F 2798 : 2009 : R2018 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
| ASTM B 746/B746M : 2016 : REDLINE | Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ASME B18.6.2 : 1998 | SLOTTED HEAD CAP SCREWS, SQAURE HEAD SET SCREWS, AND SLOTTED HEADLESS SET SCREWS (INCH SERIES) |
| ASME B16.47 : 2017 | LARGE DIAMETER STEEL FLANGES: NPS 26 THROUGH NPS 60 METRIC/INCH STANDARD |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| NBR 8800 : 2008 | DESIGN OF STEEL AND COMPOSITE STRUCTURES FOR BUILDINGS |
| ASME STS 1 : 2011 | Steel Stacks (STS-1 - 2011) |
| ASME B18.31.2 : 2014 | CONTINUOUS THREAD STUD, DOUBLE-END STUD, AND FLANGE BOLTING STUD (STUD BOLT) (INCH SERIES) |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| ASTM A 563 : 2015 : REDLINE | Standard Specification for Carbon and Alloy Steel Nuts |
| ASME B18.24 : 2015 | PART IDENTIFYING NUMBER (PIN) CODE SYSTEM STANDARD FOR B18 FASTENER PRODUCTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.