![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 2500 : 2017 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
Hardcopy , PDF
05-01-2018
English
05-01-2018
This test method covers only petroleum products and biodiesel fuels that are transparent in layers 40 mm in thickness, and with a cloud point below 49 °C.
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers only petroleum products and biodiesel fuels that are transparent in layers 40 mm in thickness, and with a cloud point below 49 °C.
Note 1:The interlaboratory program consisted of petroleum products of Test Method D1500 color of 3.5 and lower. The precisions stated in this test method may not apply to samples with ASTM color higher than 3.5.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7484 : 2023 | Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine |
ASTM D 613 : 2023 | Standard Test Method for Cetane Number of Diesel Fuel Oil |
ASTM D 8164 : 2021 | Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing |
ASTM D 7397 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Miniaturized Optical Method) |
ASTM D 5772 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Linear Cooling Rate Method) |
ASTM D 7422 : 2022 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4048 : 2022 | Standard Test Method for Detection of Copper Corrosion from Lubricating Grease |
ASTM D 8074 : 2022 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 7826 : 2022 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 6351 : 2022 | Standard Test Method for Determination of Low Temperature Fluidity and Appearance of Hydraulic Fluids |
ASTM F 715 : 2007 : R2018 | Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage |
ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
ASTM D 613 : 2018 : REV A : EDT 1 | Standard Test Method for Cetane Number of Diesel Fuel Oil |
ASTM D 7467 : 2020 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 5773 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Constant Cooling Rate Method) |
ASTM D 5966 : 2022 | Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine |
ASTM D 7468 : 2022 | Standard Test Method for Cummins ISM Test |
ASTM D 6750 : 2019 : EDT 1 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 6751 : 2020 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 8048 : 2021 : REV A : EDT 1 | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM D 7156 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4539 : 2022 | Standard Test Method for Filterability of Diesel Fuels by Low-Temperature Flow Test (LTFT) |
ASTM D 5551 : 1995 : R2019 | Standard Test Method for Determination of the Cloud Point of Oil |
ASTM D 8278 : 2020 | Standard Specification for Digital Contact Thermometers for Test Methods Measuring Flow Properties of Fuels and Lubricants |
ASTM D 97 : 2017 : REV B : R2022 | Standard Test Method for Pour Point of Petroleum Products |
ASTM D 6045 : 2020 | Standard Test Method for Color of Petroleum Products by the Automatic Tristimulus Method |
ASTM D 7689 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 975 : 2022 : REV A | Standard Specification for Diesel Fuel |
ASTM D 7484 : 2021 : REV B | Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine |
ASTM D 5967 : 2021 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
ASTM D 2864 : 2021 : REV A | Standard Terminology Relating to Electrical Insulating Liquids and Gases |
ASTM D 5771 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Optical Detection Stepped Cooling Method) |
ASTM D 5773 : 2017 : EDT 1 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Constant Cooling Rate Method) |
ASTM D 5771 : 2017 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Optical Detection Stepped Cooling Method) |
ASTM D 97 : 2017 : REV B | Standard Test Method for Pour Point of Petroleum Products |
ASTM D 7583 : 2016 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 5772 : 2017 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Linear Cooling Rate Method) |
ASTM D 5966 : 2013 | Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine (Withdrawn 2022) |
ASTM D 8048 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM D 1500 : 2012 : R2017 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 6351 : 2010 : R2016 | Standard Test Method for Determination of Low Temperature Fluidity and Appearance of Hydraulic Fluids |
ASTM D 6681 : 2017 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure |
ASTM D 7683 : 2017 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Small Test Jar Method) |
ASTM D 6923 : 2018 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure |
ASTM D 396 : 2019 | Standard Specification for Fuel Oils |
ASTM D 7826 : 2019 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 8074 : 2018 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 613 : 2018 : REV A | Standard Test Method for Cetane Number of Diesel Fuel Oil |
ASTM D 7156 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 7397 : 2017 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Miniaturized Optical Method) |
ASTM D 4048 : 2016 : EDT 1 | Standard Test Method for Detection of Copper Corrosion from Lubricating Grease |
ASTM D 6894 : 2013 | Standard Test Method for Evaluation of Aeration Resistance of Engine Oils in Direct-Injected Turbocharged Automotive Diesel Engine (Withdrawn 2022) |
ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 7689 : 2017 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 6045 : 2012 : R2017 | Standard Test Method for Color of Petroleum Products by the Automatic Tristimulus Method |
ASTM D 7422 : 2017 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 2864 : 2019 | Standard Terminology Relating to Electrical Insulating Liquids and Gases |
ASTM D 6750 : 2019 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 5967 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
ASTM D 6371 : 2017 : REV A | Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels |
ASTM D 6618 : 2016 | Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine |
ASTM D 8164 : 2019 | Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing |
ASTM D 6987/D6987M : 2013 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine (Withdrawn 2022) |
ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 4539 : 2017 | Standard Test Method for Filterability of Diesel Fuels by Low-Temperature Flow Test (LTFT) |
ASTM D 6300 : 2020 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6300 : 2013 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2014 : REV A : EDT 1 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM E 2877 : 2012 : EDT 1 | Standard Guide for Digital Contact Thermometers |
ASTM D 6300 : 2017 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2017 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM E 2251 : 2007 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
ASTM D 1500 : 2004 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 6300 : 2016 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM E 2251 : 2003 : REV A | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
ASTM D 7962 : 2015 | Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift |
ASTM D 6300 : 2004 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 7962 : 2021 | Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift |
ASTM D 6300 : 2019 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1500 : 2012 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM E 2251 : 2003 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
ASTM D 7962 : 2016 | Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift |
ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6300 : 2019 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM E 2251 : 2014 : R2021 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
ASTM D 6300 : 2020 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 1500 : 2003 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 1500 : 1982 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM E 2251 : 2010 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
ASTM D 6300 : 2020 : REV B | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6300 : 2006 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 7962 : 2015 : REV A | Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift |
ASTM D 1500 : 2002 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM E 2251 : 2011 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
ASTM E 2877 : 2012 : R2019 | Standard Guide for Digital Contact Thermometers |
ASTM E 2251 : 2014 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
ASTM D 1500 : 1998 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 1500 : 2012 : R2017 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 6300 : 2014 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2015 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 1999 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2013 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM E 2877 : 2012 | Standard Guide for Standard Guide for Digital Contact Thermometers |
ASTM D 6300 : 2008 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2003 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2007 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2002 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2016 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1500 : 2004 : REV A | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 1500 : 2007 | Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) |
ASTM D 6300 : 2014 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 7962 : 2017 | Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.