• Shopping Cart
    There are no items in your cart

ASTM D 333 : 2001 : R2013

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Guide for Clear and Pigmented Lacquers

Available format(s)

Hardcopy , PDF

Superseded date

22-06-2021

Language(s)

English

Published date

11-07-2013

€67.30
Excluding VAT

CONTAINED IN VOL. 06.02, 2017 Describes procedures for testing lacquers and lacquer coatings.

Committee
D 01
DocumentType
Guide
Pages
6
ProductNote
Reconfirmed 2013
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1These test methods cover procedures for testing lacquers and lacquer coatings. The test methods included are listed in Table 1.

Note 1In accordance with Terminology D16, a lacquer is defined as a coating composition that is based on synthetic thermoplastic filmforming material dissolved in organic solvent(s) and that dries primarily by solvent evaporation. Typical lacquers include those based on nitrocellulose, other cellulose derivatives, vinyl resins, acrylic resins, etc.
Note 2Lacquers may be applied under such diverse conditions, to so many different surfaces, and their dried films may be subjected to so many kinds of wear and exposure that it is not possible to assure desired performance from a single selection of test methods and numerical results therefrom. Those skilled in lacquer technology may find partial assurance of obtaining desired qualities in various types of lacquers through careful selection of the methods covered herein and intelligent interpretation of results therefrom.
Note 3It is intended ultimately to remove all experimental procedures from Test Methods D333 and to establish them as a guide to the selection of test methods for lacquer and perhaps to interpretation of results therefrom. Temporarily there remain in Test Methods D333 a few tests that are too short or otherwise presently unsuitable for establishment under separate ASTM designations.

1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D 2832 : 1992 : R2016 Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings
ASTM D 365 : 2001 : R2017 Standard Guide for Soluble Nitrocellulose Base Solutions
ASTM D 3023 : 1998 : R2017 Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents

ASTM D 1644 : 2001 Standard Test Methods for Nonvolatile Content of Varnishes
ASTM D 1005 : 1995 : R2020 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
ASTM D 3170 : 1987 : R1996 : EDT 1 Standard Test Method for Chipping Resistance of Coatings
ASTM D 3278 : 2020 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 870 : 2015 Standard Practice for Testing Water Resistance of Coatings Using Water Immersion
ASTM D 1475 : 2013 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 2199 : 2003 Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers
ASTM D 1210 : 1996 Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage
ASTM D 1535 : 2007 Standard Practice for Specifying Color by the Munsell System
ASTM D 2091 : 1996 Standard Test Method for Print Resistance of Lacquers
ASTM D 1014 : 2009 Standard Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates (Withdrawn 2018)
ASTM D 1475 : 1998 : R2012 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 1544 : 1998 Standard Test Method for Color of Transparent Liquids (Gardner Color Scale)
ASTM D 1729 : 2016 : REDLINE Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D 1400 : 2000 Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base (Withdrawn 2006)
ASTM D 2244 : 2015 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 823 : 1995 Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels
ASTM D 1308 : 2002 : R2013 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
ASTM D 1209 : 2000 Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D 1475 : 1985 Standard Test Method for Density of Paint, Varnish, Lacquer, and Related Products
ASTM D 1535 : 2012 : REV A Standard Practice for Specifying Color by the Munsell System
ASTM D 2244 : 2011 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 3278 : 1996 : EDT 1 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 2091 : 1996 : R2017 Standard Test Method for Print Resistance of Lacquers
ASTM D 1735 : 1999 Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 1729 : 2016 Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D 1644 : 2001 : R2006 Standard Test Methods for Nonvolatile Content of Varnishes
ASTM D 2805 : 2011 : R2018 Standard Test Method for Hiding Power of Paints by Reflectometry
ASTM D 1200 : 2010 : R2018 Standard Test Method for Viscosity by Ford Viscosity Cup
ASTM D 609 : 2017 : REDLINE Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products
ASTM D 2244 : 2009 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 660 : 1993 Standard Test Method for Evaluating Degree of Checking of Exterior Paints
ASTM D 2199 : 2003 : R2013 Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers
ASTM D 2199 : 2003 : R2007 Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers
ASTM D 2244 : 2002 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 2244 : 2016 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 1535 : 2013 Standard Practice for Specifying Color by the Munsell System
ASTM D 2091 : 1996 : R2011 Standard Test Method for Print Resistance of Lacquers
ASTM D 2244 : 2015 : EDT 1 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 2244 : 2009 : REV B Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 1186 : 1993 Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base
ASTM D 1200 : 2010 Standard Test Method for Viscosity by Ford Viscosity Cup
ASTM D 1544 : 2004 : R2018 Standard Test Method for Color of Transparent Liquids (Gardner Color Scale)
ASTM D 1475 : 1998 : R2003 Standard Test Method for Density of Liquid Coatings, Inks, and Related Products
ASTM D 2244 : 2002 : EDT 1 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 1474 : 1998 : R2002 Standard Test Methods for Indentation Hardness of Organic Coatings
ASTM D 1005 : 1995 : R2001 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
ASTM D 3170 : 2003 Standard Test Method for Chipping Resistance of Coatings
ASTM D 1644 : 2001 : R2012 Standard Test Methods for Nonvolatile Content of Varnishes
ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
ASTM D 1535 : 1968 Standard Method Of Specifying Color By The Munsell System
ASTM D 16 : 2016 : REDLINE TERMINOLOGY FOR PAINT, RELATED COATINGS, MATERIALS, AND APPLICATIONS
ASTM D 2244 : 2015 : REV A Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 445 : 1988 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity)
ASTM D 3278 : 1982 : EDT 1 Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus
ASTM D 1200 : 2010 : R2014 Standard Test Method for Viscosity by Ford Viscosity Cup
ASTM D 1210 : 2005 Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage
ASTM D 1400 : 1994 Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base
ASTM D 1644 : 2001 : R2017 Standard Test Methods for Nonvolatile Content of Varnishes
ASTM D 1735 : 2014 Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 610 : 2008 Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces
ASTM D 1729 : 1996 : R2009 Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D 1535 : 2008 : EDT 1 Standard Practice for Specifying Color by the Munsell System
ASTM D 2244 : 2016 : REDLINE Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 661 : 1993 Standard Test Method for Evaluating Degree of Cracking of Exterior Paints
ASTM D 1475 : 1960 : R1968 Standard Method Of Test For Density Of Paint, Varnish, Lacquer, And Related Products
ASTM D 2244 : 2014 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 662 : 1993 Standard Test Method for Evaluating Degree of Erosion of Exterior Paints
ASTM D 2805 : 1996 : REV A Standard Test Method for Hiding Power of Paints by Reflectometry
ASTM D 1729 : 1996 : R2003 Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D 1210 : 2005 : R2014 Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage
ASTM D 1200 : 1970 Standard Method Of Test For Viscosity Of Paints, Varnishes, And Lacquers By Ford Viscosity Cup
ASTM D 1535 : 2014 : R2018 Standard Practice for Specifying Color by the Munsell System
ASTM D 1535 : 2014 Standard Practice for Specifying Color by the Munsell System
ASTM D 1308 : 2002 : EDT 1 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
ASTM D 2244 : 2005 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 1475 : 1998 : R2008 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 445 : 2019 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 1005 : 1995 : R2013 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
ASTM D 1200 : 1994 : R2005 Standard Test Method for Viscosity by Ford Viscosity Cup
ASTM D 3170 : 2012 Standard Test Method for Chipping Resistance of Coatings
ASTM D 1209 : 2005 : EDT 1 Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D 1210 : 2005 : R2010 Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage
ASTM D 1535 : 2008 Standard Practice for Specifying Color by the Munsell System
ASTM D 1200 : 1994 : R1999 Standard Test Method for Viscosity by Ford Viscosity Cup
ASTM D 1308 : 1979 : R1981 : EDT 1 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
ASTM D 1735 : 2014 : REDLINE Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 1474 : 1998 : R2008 Standard Test Methods for Indentation Hardness of Organic Coatings
ASTM D 1735 : 2004 Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 1535 : 1997 Standard Practice for Specifying Color by the Munsell System
ASTM D 3170 : 2003 : R2007 Standard Test Method for Chipping Resistance of Coatings
ASTM D 93 : 2016-07 TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
ASTM D 1186 : 2001 Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base (Withdrawn 2006)
ASTM D 3170 : 2001 Standard Test Method for Chipping Resistance of Coatings
ASTM D 1535 : 1989 Standard Test Method for Specifying Color by the Munsell System
ASTM D 2244 : 2007 Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 1735 : 2008 Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 2620 : 1987 : R1995 : EDT 1 Standard Test Method for Light Stability of Clear Coatings (Withdrawn 2001)
ASTM D 1544 : 2004 Standard Test Method for Color of Transparent Liquids (Gardner Color Scale)
ASTM D 1308 : 1987 : R1998 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
ASTM D 1014 : 1995 Standard Practice for Conducting Exterior Exposure Tests of Paints on Steel
ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 445 : 2001 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity)
ASTM D 1535 : 2000 Standard Practice for Specifying Color by the Munsell System
ASTM D 1729 : 1996 Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D 445 : 2021 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2805 : 2011 Standard Test Method for Hiding Power of Paints by Reflectometry
ASTM D 1211 : 1997 Standard Test Method for Temperature-Change Resistance of Clear Nitrocellulose Lacquer Films Applied to Wood (Withdrawn 2006)
ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
ASTM D 2204 : 1965 : R1970 Method of Test for Perspiration Resistance of Organic Coatings (Withdrawn 1975)
ASTM D 1209 : 2005 : R2011 Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D 1544 : 2004 : R2010 Standard Test Method for Color of Transparent Liquids (Gardner Color Scale)
ASTM D 1535 : 2012 Standard Practice for Specifying Color by the Munsell System
ASTM D 1005 : 1995 : R2007 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
ASTM D 1014 : 2002 Standard Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates
ASTM D 1735 : 2002 Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
ASTM D 56 : 1987 Standard Test Method for Flash Point by Tag Closed Tester
ASTM D 1308 : 2002 : R2007 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
ASTM D 1474 : 1998 Standard Test Methods for Indentation Hardness of Organic Coatings
ASTM D 2244 : 2009 : REV A Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D 658 : 1991 Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996)
ASTM D 2244 : 1993 : R2000 Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates
ASTM D 2090 : 1998 Standard Test Method for Clarity and Cleanness of Paint and Ink Liquids (Withdrawn 2007)
ASTM D 1209 : 2005 Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
ASTM D 1535 : 2006 Standard Practice for Specifying Color by the Munsell System
ASTM D 1475 : 2013 : REDLINE Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 522 : 1993 : REV A Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
ASTM D 2199 : 1982 : R1999 Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers
ASTM D 1535 : 2001 Standard Practice for Specifying Color by the Munsell System
ASTM D 1475 : 1998 Standard Test Method for Density of Liquid Coatings, Inks, and Related Products
ASTM D 659 : 1986 : EDT 1 Method of Evaluating Degree of Chalking of Exterior Paints
ASTM D 3278 : 1996 : R2004 : EDT 1 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 2805 : 1996 : REV A : R2003 Standard Test Method for Hiding Power of Paints by Reflectometry
ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 1005 : 1995 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
ASTM D 1308 : 2002 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
ASTM D 3278 : 1996 : R2011 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus (Withdrawn 2020)
ASTM D 2091 : 1996 : R2003 Standard Test Method for Print Resistance of Lacquers
ASTM D 1209 : 2005 : R2019 Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.