BS EN 10028-7:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Flat products made of steels for pressure purposes Stainless steels
Hardcopy , PDF
11-09-2018
English
31-01-2008
Important note : Users cannot be edited or removed once added to your Multi user PDF.
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Tolerances on dimensions
5 Calculation of mass
6 Classification and designation
7 Information to be supplied by the purchaser
8 Requirements
9 Inspection
10 Sampling
11 Test methods
12 Marking
Annex A (informative) - Guidelines for further
treatment (including heat treatment in
fabrication)
Annex B (informative) - Post weld heat treatment
Annex C (informative) - Preliminary reference
data for the tensile strength of austenitic-ferritic
steels at elevated temperatures
Annex D (informative) - Reference data of strength
values for 1% (plastic) creep strain and
creep rupture
Annex E (informative) - Reference data on
mechanical properties of austenitic steels at
room temperature and at low temperatures
Annex F (informative) - Significant changes to
the version EN 10028-7:2007
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of Directive 2014/68/EU
Bibliography
Describes requirements for flat products for pressure purposes made of stainless steels, including austenitic creep resisting steels, in thicknesses.
| Committee |
ISE/105
|
| DevelopmentNote |
Supersedes BS 1501-3(1990) (06/2000) Supersedes 96/703163 DC (08/2004) Supersedes 05/30133802 DC. (01/2008) Supersedes 13/30288581 DC. (07/2016)
|
| DocumentType |
Standard
|
| Pages |
50
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 10028-7:2016-10 | Identical |
| NBN EN 10028-7 : 2008 | Identical |
| UNE-EN 10028-7:2016 | Identical |
| SN EN 10028-7 : 2016 | Identical |
| NS EN 10028-7 : 2000 | Identical |
| EN 10028-7:2016 | Identical |
| NEN EN 10028-7 : 2016 | Identical |
| I.S. EN 10028-7:2016&LC:2016 | Identical |
| UNI EN 10028-7 : 2008 | Identical |
| NF EN 10028-7 : 2016 | Identical |
| DIN EN 10028-7:2000-06 | Identical |
| CSA LNG 2-2017 | LIQUEFIED NATURAL GAS VEHICLE FUEL CONTAINERS |
| DEFSTAN 02-329/2(2005) : 2005 | REQUIREMENTS FOR HEAT EXCHANGERS FOR HM SURFACE SHIPS AND SUBMARINES |
| DEFSTAN 02-329/3(2010) : 2010 | REQUIREMENTS FOR HEAT EXCHANGERS FOR HM SURFACE SHIPS AND SUBMARINES |
| DEFSTAN 02-329/4(2015) : 2015 | REQUIREMENTS FOR HEAT EXCHANGERS FOR HM SURFACE SHIPS AND SUBMARINES |
| DEFSTAN 02-305/2(2003) : 2003 | REQUIREMENTS FOR GEARING - MAIN PROPULSION |
| DEFSTAN 02-305/3(2010) : 2010 | REQUIREMENTS FOR GEARING - MAIN PROPULSION |
| 07/30160560 DC : DRAFT JAN 2007 | PD 5500 AMD 2 - SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS PD5500(2015) : 2015 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS PD5500(2009) : 2009 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| PD 5500:2003 | Specification for unfired fusion welded pressure vessels |
| BS PD5500(2018) : 2018 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS PD5500(2006) : 2006 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS PD5500(2012) : 2012 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| EN ISO 9445-2:2010 | Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and plate/sheet (ISO 9445-2:2009) |
| ISO 9444-2:2009 | Continuously hot-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and sheet/plate |
| EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| EN ISO 643:2012 | Steels - Micrographic determination of the apparent grain size (ISO 643:2012) |
| NFA 36 209 : 1990 | IRON AND STEEL PRODUCTS - AUSTENITIC STAINLESS STEELS FOR BOILERS AND PRESSURE VESSELS |
| EN ISO 9444-2:2010 | Continuously hot-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and sheet/plate (ISO 9444-2:2009) |
| EN ISO 18286:2010 | Hot-rolled stainless steel plates - Tolerances on dimensions and shape (ISO 18286:2008) |
| DIN 17460:1992-09 | HIGH TEMPERATURE AUSTENITIC STEEL PLATE AND SHEET, COLD AND HOT ROLLED STRIP, BARS AND FORGINGS - TECHNICAL DELIVERY CONDITIONS |
| ISO 9445-2:2009 | Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate/sheet |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| ISO 643:2012 | Steels Micrographic determination of the apparent grain size |
| ISO 18286:2008 | Hot-rolled stainless steel plates — Tolerances on dimensions and shape |
| PD 6525-1:1990 | Elevated temperature properties for steels for pressure purposes. Stress rupture properties |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.