• BS EN 61800-2:2015 (published 2015-10)

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Adjustable speed electrical power drive systems General requirements. Rating specifications for low voltage adjustable speed a.c. power drive systems

    Available format(s):  Hardcopy, PDF

    Superseded date:  18-05-2022

    Language(s):  English

    Published date:  31-10-2015

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Ratings and specifications for the act of
      installing, commissioning and operation
    5 Test
    6 Information and marking requirements
    Annex A (informative) - Classification of PDS into
            low-voltage system and high-voltage system
    Annex B (informative) - Determination of the input
            current of BDM/CDM/PDS
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Pertains to adjustable speed electric a.c power drive systems, which include semiconductor power conversion and the means for their control, protection, monitoring, measurement and the a.c motors.

    Scope - (Show below) - (Hide below)

    This part of IEC61800 applies to adjustable speed electric a.c. power drive systems, which include semiconductor power conversion and the means for their control, protection, monitoring, measurement and the a.c. motors. It applies to adjustable speed electric power drive systems intended to feed a.c. motors from a BDM connected to line-to-line voltages up to and including 1kV a.c. 50Hz or 60Hz and/or voltages up to and including 1,5kV d.c. input side. NOTE1 Adjustable speed electric a.c. power drive systems intended to feed a.c. motors, and with rated converter input voltages above 1000V a.c. are covered by IEC618004 . NOTE2 Adjustable speed electric d.c. power drive systems intended to feed d.c. motors are covered by IEC618001 . NOTE3 For adjustable speed electric a.c. power drive systems having series-connected electronic power converter sections, the line-to-line voltage is the sum of the series connected input voltages. Traction applications and electric vehicles are excluded from the scope of this standard. This part of IEC61800 is intended to define the following aspects of an a.c. power drive system ( PDS): principal parts of the PDS; ratings and performance; specifications for the environment in which the PDS is intended to be installed and operated; other specifications which might be applicable when specifying a complete PDS. This standard provides minimum requirements, which may be used for the development of a specification between customer and manufacturer. Compliance with this standard is possible only when each topic of this standard is individually specified by the customer developing specifications or by product standard committees developing product standards. For some aspects which are covered by specific PDS product standards in the IEC61800 Series, this document provides a short introduction and reference to detailed requirements in these product standards. This applies to the following aspects: EMC which is covered in IEC618003 ; electrical safety which is covered in IEC6180051 ; functional safety which is covered in IEC6180052 ; type of load duty which are covered by IECTR618006 ; communication profiles which are covered by IEC618007 Series; power interface voltage specification which is covered by IECTS618008 .

    General Product Information - (Show below) - (Hide below)

    Committee PEL/22
    Development Note Supersedes 95/210630 DC. (09/2005) 1998 Edition remains active & will be withdrawn on 26/08/2018. Supersedes 13/30248785 DC. (10/2015)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61800-3:2017 Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods
    IEC 60038:2009 IEC standard voltages
    IEC 61800-4:2002 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
    IEC 61158-2:2014 Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition
    EN 60721-3-1:1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STORAGE
    IEC 60068-2-68:1994 Environmental testing - Part 2-68: Tests - Test L: Dust and sand
    EN 60146-1-1:2010 SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS
    EN 61800-5-2:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL (IEC 61800-5-2:2016)
    IEC 60034-9:2003+AMD1:2007 CSV Rotating electrical machines - Part 9: Noise limits
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    IEC TS 62578:2015 Power electronics systems and equipment - Operation conditions and characteristics of active infeed converter (AIC) applications including design recommendations for their emission values below 150 kHz
    IEC 61800-7-1:2015 Adjustable speed electrical power drive systems - Part 7-1: Generic interface and use of profiles for power drive systems - Interface definition
    EN 60068-2-2:2007 ENVIRONMENTAL TESTING - PART 2-2: TESTS - TEST B: DRY HEAT
    CLC/TR 61800-6 : 2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 6: GUIDE FOR DETERMINATION OF TYPES OF LOAD DUTY AND CORRESPONDING CURRENT RATINGS
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    EN 50325-4 : 2002 INDUSTRIAL COMMUNICATIONS SUBSYSTEM BASED ON ISO 11898 (CAN) FOR CONTROLLER-DEVICE INTERFACES - PART 4: CANOPEN
    EN 60034-9:2005/A1:2007 ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
    IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
    EN 60068-2-27:2009 ENVIRONMENTAL TESTING - PART 2-27: TESTS - TEST EA AND GUIDANCE: SHOCK
    EN 61800-5-1:2007/A1:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007/A1:2016)
    IEC 60721-2-6:1990 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - ENVIRONMENTAL CONDITIONS APPEARING IN NATURE - EARTHQUAKE VIBRATION AND SHOCK
    IEC 60146-1-1:2009 Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements
    IEC TR 60146-1-2:2011 Semiconductor converters - General requirements and line commutated converters - Part 1-2: Application guide
    IEC 60027-3:2002 Letter symbols to be used in electrical technology - Part 3: Logarithmic and related quantities, and their units
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60721-3-2:1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3-2: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - TRANSPORTATION AND HANDLING
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    EN 60664-1:2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    EN 60068-2-68 : 1996 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST L: DUST AND SAND
    EN 50598-2:2014/A1:2016 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    EN 50598-3 : 2015 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - PART 3: QUANTITATIVE ECO DESIGN APPROACH THROUGH LIFE CYCLE ASSESSMENT INCLUDING PRODUCT CATEGORY RULES AND THE CONTENT OF ENVIRONMENTAL DECLARATIONS
    IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
    EN 60068-2-78:2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012)
    IEC 61378-3:2015 Converter transformers - Part 3: Application guide
    IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
    EN 60068-2-6:2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    EN 61800-3 : 2004 AMD 1 2012 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004/A1:2011)
    IEC 61131-2:2017 Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests
    EN 61800-7-1:2016 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 7-1: GENERIC INTERFACE AND USE OF PROFILES FOR POWER DRIVE SYSTEMS - INTERFACE DEFINITION (IEC 61800-7-1:2015)
    IEC 61439-1:2011 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
    EN 60721-3-2 : 1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - TRANSPORTATION
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    IEC TR 61800-6:2003 Adjustable speed electrical power drive systems - Part 6: Guide for determination of types of load duty and corresponding current ratings
    EN 50495 : 2010 SAFETY DEVICES REQUIRED FOR THE SAFE FUNCTIONING OF EQUIPMENT WITH RESPECT TO EXPLOSION RISKS
    EN 60721-3-4:1995/A1:1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - SECTION 4: STATIONARY USE AT NON-WEATHER-PROTECTED LOCATIONS
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    IEC 60068-2-52:2017 ENVIRONMENTAL TESTING - PART 2-52: TESTS - TEST KB: SALT MIST, CYCLIC (SODIUM CHLORIDE SOLUTION)
    IEC 61378-1:2011 Converter transformers - Part 1: Transformers for industrial applications
    IEC 61800-5-2:2016 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
    EN 60038 : 2011 CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED)
    IEC 61800-1:1997 Adjustable speed electrical power drive systems - Part 1: General requirments - Rating specifications for low voltage adjustables speed d.c. power drive systems
    IEC 60721-3-1:1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3-1: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STORAGE
    EN 60721-3-3 : 95 AMD 2 97 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective