• BS EN 62196-1:2014 (published 2015-01)

    Current The latest, up-to-date edition.

    Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles General requirements

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  31-01-2015

    Publisher:  British Standards Institution

    Add To Cart

    Scope - (Show below) - (Hide below)

    This part of IEC62196 is applicable to plugs, socket-outlets, vehicle connectors, vehicle inlets and cable assemblies for electric vehicles, herein referred to as accessories, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding 690V a.c. 50Hz to 60Hz, at a rated current not exceeding 250A, 1500V d.c. at a rated current not exceeding 400A. These accessories are intended to be installed by instructed persons ( IEC60050195:1998 , IEC60050195/AMD1:2001, 195-04-02) or skilled persons ( IEC60050195:1998 , IEC60050195/AMD1:2001, 195-04-01) only. These accessories and cable assemblies are intended to be used for circuits specified in IEC618511 which operate at different voltages and frequencies and which may include extra-low voltage and communication signals. These accessories and cable assemblies are to be used at an ambient temperature between -30C and+50C. NOTE1 In some countries, other requirements may apply. NOTE2 the following countries, -35C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this part of IEC62196 are for use in certain modes of charging electric vehicles. These modes are defined in IEC618511 . These definitions and a description of the types of connection (cases A, B and C), are described in IEC618511:2010, 6.2 and 6.3.1. NOTE3 In the following countries, mode 1 will not be allowed: UK, US, CA, SG. This part of IEC62196 does not apply to those standardised accessories used in charging systems where the use of such accessories constructed to the requirements of other standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be used for those situations (mode and case) identified in IEC618511 . This part of IEC62196 may be used as a guide for accessories with a lesser number of contacts and lower ratings for use with light duty vehicles.

    General Product Information - (Show below) - (Hide below)

    Committee PEL/23/4
    Development Note Supersedes 01/202446 DC (05/2004). 2003 version remains current. Supersedes 10/30216162 DC. (06/2012) 2012 Edition remains current and will be withdrawn on 15/10/2017. (07/2013) 2012 + A11 2013 Edition remains active & will be withdrawn on 16/06/2017. Supersedes 13/30295015 DC. (10/2014) 2012 + A12 2014 Edition remains active & will be withdrawn on 29/09/2019. Supersedes 13/30277668 DC. (02/2015)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
    EN 60999-2:2003 CONNECTING DEVICES - ELECTRICAL COPPER CONDUCTORS - SAFETY REQUIREMENTS FOR SCREW-TYPE AND SCREWLESS-TYPE CLAMPING UNITS - PART 2: PARTICULAR REQUIREMENTS FOR CLAMPING UNITS FOR CONDUCTORS ABOVE 35 MM[2] UP TO 300 MM[2] (INCLUDED)
    EN 61851-1:2011 Electric vehicle conductive charging system - Part 1: General requirements
    IEC 62752:2016 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
    EN 60068-2-75:2014 ENVIRONMENTAL TESTING - PART 2-75: TESTS - TEST EH: HAMMER TESTS (IEC 60068-2-75:2014)
    IEC 61540:1997+AMD1:1998 CSV Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)
    IEC 60228:2004 Conductors of insulated cables
    IEC 60245-6:1994 Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 6: Arc welding electrode cables
    EN 61851-23:2014/AC:2016-06 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: DC ELECTRIC VEHICLE CHARGING STATION (IEC 61851-23:2014/COR1:2016)
    IEC 60309-4:2006+AMD1:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 4: Switched socket-outlets and connectors with or without interlock
    EN 60695-10-2:2014 FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD (IEC 60695-10-2:2014)
    EN 60309-4:2007/A1:2012 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 4: SWITCHED SOCKET-OUTLETS AND CONNECTORS WITH OR WITHOUT INTERLOCK (IEC 60309-4:2006/A1:2012)
    EN 61300-2-6:2011 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - BASIC TEST AND MEASUREMENT PROCEDURES - PART 2-6: TESTS - TENSILE STRENGTH OF COUPLING MECHANISM
    IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV Plugs and socket-outlets for household and similar purposes - Part1: General requirements
    IEC 60050-441:1984 International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
    IEC 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
    IEC 60269-2:2013+AMD1:2016 CSV Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K
    IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules
    IEC 62335:2008 Circuit breakers - Switched protective earth portable residual current devices for class I and battery powered vehicle applications
    IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
    EN 60228:2005 COR 2005 CONDUCTORS OF INSULATED CABLES
    IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV Low-voltage fuses - Part 1: General requirements
    EN ISO 1456 : 2009 METALLIC AND OTHER INORGANIC COATINGS - ELECTRODEPOSITED COATINGS OF NICKEL, NICKEL PLUS CHROMIUM, COPPER PLUS NICKEL AND OF COPPER PLUS NICKEL PLUS CHROMIUM
    EN 60947-1:2007/A2:2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014)
    ISO 2081:2008 Metallic and other inorganic coatings Electroplated coatings of zinc with supplementary treatments on iron or steel
    IEC 61009-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers with integral overcurrentprotection for household and similar uses (RCBOs) - Part 1: General rules
    EN 60112 : 2003 AMD 1 2009 METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
    IEC 60999-1:1999 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
    ISO 1456:2009 Metallic and other inorganic coatings — Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium
    EN 61009-1:2012/A12:2016 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCBOS) - PART 1: GENERAL RULES
    IEC TR 60755:2008 General requirements for residual current operated protective devices
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60245-4:2011 Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 4: Cords and flexible cables
    IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
    IEC 61300-2-7:2013 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-7: Tests - Bending moment
    EN 62752:2016 IN-CABLE CONTROL AND PROTECTION DEVICE FOR MODE 2 CHARGING OF ELECTRIC ROAD VEHICLES (IC-CPD) (IEC 62752:2016)
    ISO 2093:1986 Electroplated coatings of tin — Specification and test methods
    EN 60664-1:2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    EN 61300-2-4 : 1997 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES - PART 2-4: TESTS - FIBRE/CABLE RETENTION (IEC 61300-2-4:1995)
    HD 193 : 200S2 VOLTAGE BANDS FOR ELECTRICAL INSTALLATIONS OF BUILDINGS
    HD 60269-2:2013 Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K
    IEC 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
    IEC 60664-3:2016 Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
    EN 60999-1 : 2000 CONNECTING DEVICES - ELECTRICAL COPPER CONDUCTORS - SAFETY REQUIREMENTS FOR SCREW-TYPE AND SCREWLESS-TYPE CLAMPING UNITS - PART 1: GENERAL REQUIREMENTS AND PARTICULAR REQUIREMENTS FOR CLAMPING UNITS FOR CONDUCTORS FROM 0,2 MM[2] UP TO 35 MM[2] (INCLUDED)
    IEC 60695-10-2:2014 Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
    IEC 61300-2-4:1995 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention
    EN 61008-1:2012/A12:2017 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCBS) - PART 1: GENERAL RULES (IEC 61008-1:2010, MODIFIED)
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements
    IEC 61300-2-6:2010 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN 60068-2-14:2009 ENVIRONMENTAL TESTING - PART 2-14: TESTS - TEST N: CHANGE OF TEMPERATURE
    EN 60664-3:2017 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 3: USE OF COATING, POTTING OR MOULDING FOR PROTECTION AGAINST POLLUTION (IEC 60664-3:2016)
    EN 61300-2-7:2013 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - BASIC TEST AND MEASUREMENT PROCEDURES - PART 2-7: TESTS - BENDING MOMENT (IEC 61300-2-7:2013)
    IEC 61851-1:2017 Electric vehicle conductive charging system - Part 1: General requirements
    EN 60695-2-11:2014 FIRE HAZARD TESTING - PART 2-11: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY TEST METHOD FOR END-PRODUCTS (GWEPT) (IEC 60695-2-11:2014)
    EN 60269-1:2007/A2:2014 LOW-VOLTAGE FUSES - PART 1: GENERAL REQUIREMENTS (IEC 60269-1:2006/A2:2014)
    EN 60309-1:1999/A1:2007/AC:2014 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60309-1:1999/A2:2012)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective