CAN/CSA-C22.2 NO. 60950-22:17
Current
The latest, up-to-date edition.
Information technology equipment - Safety - Part 22: Equipment to be installed outdoors (Binational standard with UL 60950-22)
Hardcopy , PDF , Hardcopy, PDF
French, English
01-01-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.
PREFACE
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Conditions for outdoor equipment
5 Marking and instructions
6 Protection from electrical shock in an outdoor location
7 Wiring terminals for connection of external conductors
8 Construction requirements for outdoor enclosures
9 Protection of equipment within an outdoor enclosure
10 Mechanical strength of enclosures
11 Outdoor equipment containing valve regulated or
vented batteries
Annex A (normative) - Water-saturated sulphur dioxide
atmosphere
Annex B (normative) - Water spray test
Annex C (normative) - Ultraviolet light conditioning test
Annex D (normative) - Gasket tests
Annex E (informative) - Rationale
Annex NAE (informative) - U.S. and Canadian regulatory
requirements
Bibliography
This part of IEC 60950 applies to information technology equipment intended to be installed in an OUTDOOR LOCATION.
| DevelopmentNote |
Jointly published by CSA and UL. Also numbered as UL 60950-22. (04/2017)
|
| DocumentType |
Standard
|
| ISBN |
978-1-4883-0706-5
|
| Pages |
53
|
| PublisherName |
Canadian Standards Association
|
| Status |
Current
|
Preface This is the harmonized CSA and UL Standard for Information Technology Equipment - Safety - Part 22: Equipment to be Installed Outdoors. It is the second edition of CAN/CSA-C22.2 No. 60950-22 and the second edition of UL 60950-22. This edition of CAN/CSA-C22.2 No. 60950-22 supersedes the previous edition published on April 23, 2007. This edition of UL 60950-22 supersedes the previous edition published on April 23, 2007. This harmonized standard is based on IEC Publication 60950-22: second edition, Information Technology Equipment - Safety - Part 22: Equipment to be Installed Outdoors, issued January 2016. IEC 60950-22 is copyrighted by the IEC. Scope 1.1 Equipment covered This part of IEC 60950 applies to information technology equipment intended to be installed in an OUTDOOR LOCATION. The requirements for OUTDOOR EQUIPMENT also apply, where relevant, to OUTDOOR ENCLOSURES suitable for direct installation in the field and supplied for housing information technology equipment to be installed in an OUTDOOR LOCATION. 1.2 Additional requirements Each installation may have particular requirements. Some examples are given in 4.2. In addition, requirements for protection of the OUTDOOR EQUIPMENT against the effects of direct lightning strikes are not covered by the standard. For information on this subject, see IEC 62305-1 NFPA 780 or CAN/CSA-B72.
| Standards | Relationship |
| IEC 60950-22:2016 | Identical |
| CSA C22.2 No. 94.1 : 2015 | ENCLOSURES FOR ELECTRICAL EQUIPMENT, NON-ENVIRONMENTAL CONSIDERATIONS |
| ISO 4892-1:2016 | Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance |
| IEC 60364-4-43:2008 | Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent |
| UL 50:13ED 2015-10-16 | Enclosures for Electrical Equipment, Non-Environmental Considerations |
| NFPA 780 : 2017 | INSTALLATION OF LIGHTNING PROTECTION SYSTEMS |
| IEC 61587-1:2016 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation |
| IEC 60896-21:2004 | Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test |
| IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV | Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| CSA C22.2 No. 144 : 1991 | GROUND FAULT CIRCUIT INTERRUPTERS |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| UL 943:5ED 2016-05-17 | Ground-Fault Circuit-Interrupters |
| ISO 14993:2001 | Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 21207:2015 | Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| IEEE C2-2017 | NATIONAL ELECTRICAL SAFETY CODE (NESC)(R) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60896-22:2004 | Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements |
| ISO/TS 18173:2005 | Non-destructive testing General terms and definitions |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| CSA C22.2 No. 62368-1 : 2014 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| IEC 61643-11:2011 | Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods |
| IEC 61969-3:2011 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects |
| ISO 4892-4:2013 | Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps |
| IEC 61439-5:2014 | Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 62485-2:2010 | Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries |
| CSA C22.2 No. 94.2 : 2015 | ENCLOSURES FOR ELECTRICAL EQUIPMENT, ENVIRONMENTAL CONSIDERATIONS |
| ISO 3231:1993 | Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.