EN 848-2 : 2007 COR 2012
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES
Withdrawn date
20-04-2022
Published date
12-01-2013
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (normative) - Stability test for displaceable
machines
Annex B (normative) - Braking tests
Annex C (normative) - Impact test method for guards
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
Describes all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable single spindle hand fed/integrated fed routing machines with fixed head but allowing only movement along the axis of the tool during machining hereinafter referred to as "machines" designed to cut solid wood, chip board, fibreboard, plywood and also these materials if they are covered with plastic laminate, edgings or veneer when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
| Committee |
TC 142
|
| DevelopmentNote |
2007 Edition Re-Issued in September 2012 & incorporates AMD 2 2012. (10/2012)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Withdrawn
|
| Standards | Relationship |
| NEN EN 848-2 : 2007 + A2 2012 | Identical |
| BS EN 848-2 : 2007 | Identical |
| PN EN 848-2 : 2010 + A2 2013 | Identical |
| UNE-EN 848-2:2007 | Identical |
| DIN EN 848-2:2013-01 | Identical |
| UNI EN 848-2 : 2013 | Identical |
| I.S. EN 848-2:2007 | Identical |
| NBN EN 848-2 : 2007 + A2 2012 | Identical |
| NF EN 848-2 : 2007 + A2 2012 | Identical |
| SN EN 848-2 : 2007 + A2 2012 | Identical |
| NS EN 848-2 : 2007 + A2 2012 | Identical |
| 10/30233212 DC : 0 | BS EN 848-3 - SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| 14/30297793 DC : 0 | BS EN ISO 19085-3 - WOODWORKING MACHINES - SAFETY REQUIREMENTS - PART 3: NC BORING AND ROUTING MACHINES |
| DIN EN 848-3:2013-01 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| UNE-EN 848-3:2013 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines |
| UNI EN 848-3 : 2012 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| I.S. EN 848-3:2012 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| PREN 848-3 : DRAFT 2010 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| EN 848-3:2012 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines |
| BS EN 848-3:2012 | Safety of woodworking machines. One side moulding machines with rotating tool Numerically controlled (NC) boring and routing machines |
| EN 1005-4:2005+A1:2008 | Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN 60745-1:2009/A11:2010 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 848-3:2012 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 61800-5-2:2017 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN ISO 3743-2:2009 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| ISO 7960:1995 | Airborne noise emitted by machine tools Operating conditions for woodworking machines |
| EN 60745-2-17:2010 | Hand-held motor-operated electric tools - Safety - Part 2-17: Particular requirements for routers and trimmers |
| EN 1093-9:1998+A1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 614-2:2000+A1:2008 | Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks |
| EN 50370-2:2003 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| EN 847-3:2013 | Tools for woodworking - Safety requirements - Part 3: Clamping devices |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1005-1:2001+A1:2008 | Safety of machinery - Human physical performance - Part 1: Terms and definitions |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| EN 12779:2015 | Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| IEC 60745-2-17:2010 | Hand-held motor-operated electric tools - Safety - Part 2-17: Particular requirements for routers and trimmers |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN 61029-2-8:2010 | Safety of transportable motor-operated electric tools - Part 2-8: Particular requirements for single spindle vertical moulders |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| IEC 61029-1:1990 | Safety of transportable motor-operated electric tools - Part 1: General requirements |
| HD 22-4 : 200S4 | CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING CROSS-LINKED INSULATION - PART 4: CORDS AND FLEXIBLE CABLES |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 60947-4-1 : 2010 AMD 1 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 847-2:2017 | Tools for woodworking - Safety requirements - Part 2: Requirements for the shank of shank mounted milling tools/circular saw blades |
| ISO 7948:1987 | Woodworking machines Routing machines Nomenclature and acceptance conditions |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| EN 62061:2005/A2:2015 | SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015) |
| IEC 60439-1:1999+AMD1:2004 CSV | Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| IEC 60745-1:2006 | Hand-held motor-operated electric tools - Safety - Part 1: General requirements |
| EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN 847-1:2017 | Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 61029-1:2009/A11:2010 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS |
| EN 1005-3:2002+A1:2008 | Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| IEC 61029-2-8:1995 | Safety of transportable motor-operated electric tools - Part 2: Particular requirements for single spindle vertical moulders |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN 50370-1:2005 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| EN 1093-11:2001+A1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index |
| IEC 61800-5-2:2016 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.