EN ISO 2719:2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016)
Amended by
Published date
20-07-2016
Publisher
Superseded date
10-04-2021
Sorry this product is not available in your region.
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Chemicals and materials
6 Apparatus
7 Apparatus preparation
8 Sampling
9 Sample handling
10 Procedure
11 Calculation
12 Expression of results
13 Precision
14 Test report
Annex A (informative) - Apparatus verification
Annex B (normative) - Pensky-Martens closed cup test
apparatus
Annex C (normative) - Temperature measuring device
specification
Bibliography
ISO 2719:2016 describes three procedures, A, B and C, using the Pensky-Martens closed cup tester, for determining the flash point of combustible liquids, liquids with suspended solids, liquids that tend to form a surface film under the test conditions, biodiesel and other liquids in the temperature range of 40 °C to 370 °C.CAUTION - For certain mixtures no flash point, as defined, is observed; instead a significant enlargement of the test flame (not halo effect) and a change in colour of the test flame from blue to yellowish-orange can occur. Continued heating can result in significant burning of vapours outside the test cup, and can be a potential fire hazard.NOTE 1 Although, technically, kerosene with a flash point above 40 °C can be tested using this International Standard, it is standard practice to test kerosene according to ISO 13736.[5] Similarly, lubricating oils are normally tested according to ISO 2592[2].Procedure A is applicable to distillate fuels (diesel, biodiesel blends, heating oil and turbine fuels), new and in-use lubricating oils, paints and varnishes, and other homogeneous liquids not included in the scope of Procedures B or C.Procedure B is applicable to residual fuel oils, cutback residua, used lubricating oils, mixtures of liquids with solids, liquids that tend to form a surface film under test conditions or are of such kinematic viscosity that they are not uniformly heated under the stirring and heating conditions of Procedure A.Procedure C is applicable to fatty acid methyl esters (FAME) as specified in specifications such as EN 14214[11] or ASTM D6751[13].ISO 2719:2016 is not applicable to water-borne paints and varnishes.NOTE 2 Water-borne paints and varnishes can be tested using ISO 3679[3]. Liquids containing traces of highly volatile materials can be tested using ISO 1523[1] or ISO 3679.
| Committee |
CEN/TC 19
|
| DevelopmentNote |
Supersedes EN 22719 (12/2003)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| NBN EN ISO 2719 : 2003 | Identical |
| NEN EN ISO 2719 : 2016 | Identical |
| NS EN ISO 2719 : 2002 | Identical |
| I.S. EN ISO 2719:2016 | Identical |
| PN EN ISO 2719 : 2016 | Identical |
| NF EN ISO 2719:2018 | Identical |
| SS-EN ISO 2719 : 2016 | Identical |
| BS EN ISO 2719:2002 | Identical |
| NF EN ISO 2719 : 2003 | Identical |
| DIN EN ISO 2719:2015-07 (Draft) | Identical |
| DIN EN ISO 2719:2016-11 | Identical |
| BS 2000-34(2016) : 2016 | Identical |
| GOST R EN ISO 2719 : 2008 | Identical |
| ISO 2719:2016 | Identical |
| ONORM EN ISO 2719 : 2016 | Identical |
| DIN EN ISO 2719:2003-09 | Identical |
| NS-EN ISO 2719:2016 | Identical |
| DS EN ISO 2719 : 2016 | Identical |
| BS EN ISO 2719:2016 | Equivalent |
| BS EN ISO 2719:2016 | Identical |
| UNE-EN ISO 2719:2017 | Identical |
| BS EN 16734 : 2016 | AUTOMOTIVE FUELS - AUTOMOTIVE B10 DIESEL FUEL - REQUIREMENTS AND TEST METHODS |
| 14/30301257 DC : 0 | BS EN 13160-3 - LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS |
| 04/101637 DC : DRAFT JAN 2004 | ISO 19353 - SAFETY OF MACHINERY - FIRE PREVENTION AND PROTECTION |
| 17/30359196 DC : DRAFT SEP 2017 | BS EN 16709 AMD 1 - AUTOMOTIVE FUELS - HIGH FAME DIESEL FUEL (B20 AND B30) - REQUIREMENTS AND TEST METHODS |
| 14/30294041 DC : 0 | BS EN 16709 - AUTOMOTIVE FUELS - HIGH FAME DIESEL FUEL (B20 OR B30) - REQUIREMENTS AND TEST METHODS |
| PD CEN/TR 16389:2017 | Automotive fuels. Paraffinic diesel fuel and blends with FAME. Background to the parameters required and their respective limits and determination |
| 09/30205523 DC : 0 | BS EN 14214 - AUTOMOTIVE FUELS - FATTY ACID METHYL ESTERS (FAME) FOR DIESEL ENGINES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 15322:2013 | BITUMEN AND BITUMINOUS BINDERS - FRAMEWORK FOR SPECIFYING CUT-BACK AND FLUXED BITUMINOUS BINDERS |
| BS EN 16900:2017 | Fast pyrolysis bio-oils for industrial boilers. Requirements and test methods |
| BS EN 45545-1:2013 | Railway applications. Fire protection on railway vehicles General |
| BS EN 60836:2015 | Specifications for unused silicone insulating liquids for electrotechnical purposes |
| CEI EN 61099 : 2011 | INSULATING LIQUIDS - SPECIFICATIONS FOR UNUSED SYNTHETIC ORGANIC ESTERS FOR ELECTRICAL PURPOSES |
| PD CEN/TR 17103:2017 | Petroleum and related products. Fast pyrolysis bio-oils for stationary internal combustion engines. Quality determination |
| 09/30202307 DC : 0 | BS EN 12514-1 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 1: SAFETY REQUIREMENTS AND TESTS - TERMINOLOGY, GENERAL REQUIREMENTS |
| S.R. CLC/TR 50503:2010 | GUIDELINES FOR THE INVENTORY CONTROL, MANAGEMENT, DECONTAMINATION AND/OR DISPOSAL OF ELECTRICAL EQUIPMENT AND INSULATING LIQUIDS CONTAINING PCBS |
| S.R. CEN/TS 15940:2012 | AUTOMOTIVE FUELS - PARAFFINIC DIESEL FUEL FROM SYNTHESIS OR HYDROTREATMENT - REQUIREMENTS AND TEST METHODS |
| EN 16734:2016 | Automotive fuels - Automotive B10 diesel fuel - Requirements and test methods |
| BS EN 14214:2012 | LIQUID PETROLEUM PRODUCTS - FATTY ACID METHYL ESTERS (FAME) FOR USE IN DIESEL ENGINES AND HEATING APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| BS EN 16709 : 2015 | AUTOMOTIVE FUELS - HIGH FAME DIESEL FUEL (B20 AND B30) - REQUIREMENTS AND TEST METHODS |
| EN 15940:2016 | Automotive fuels - Paraffinic diesel fuel from synthesis or hydrotreatment - Requirements and test methods |
| DIN EN 13341:2011-04 | Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods (includes Amendment A1:2011) |
| BS EN 14998:2005 | Derivatives from coal pyrolysis. Coal tar based oils: fluxings oils. Specifications and test methods |
| BS EN 14264:2003 | Derivatives from coal pyrolysis. Coal tar and pitch based binders and related products. Impregnating pitch. Characteristics and test methods |
| BS EN 14733 : 2005 | BITUMEN AND BITUMINOUS BINDERS - BITUMINOUS EMULSIONS, FLUXED AND CUT-BACK BITUMEN FACTORY PRODUCTION CONTROL |
| BS EN 13991:2003 | Derivatives from coal pyrolysis. Coal tar based oils. Creosotes. Specifications and test methods |
| BS EN 12591:2009 | Bitumen and bituminous binders. Specifications for paving grade bitumens |
| CEN/TR 15138:2005 | Petroleum products and other liquids - Guide to flash point testing |
| CEN/TS 45545-7:2009 | Railway applications - Fire protection on railway vehicles - Part 7: Fire safety requirements for flammable liquid and flammable gas installations |
| EN 13160-3:2016 | Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks |
| DIN EN 14998:2005-04 | Derivatives from coal pyrolysis - Coal tar based oils: fluxing oils - Specifications and test methods |
| EN 13341:2005+A1:2011 | Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods |
| EN 61099:2010 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| CEI UNI EN 45545-1 : 2013 | RAILWAY APPLICATIONS - FIRE PROTECTION ON RAILWAY VEHICLES - PART 1: GENERAL |
| PD CEN/TR 16557:2013 | Automotive fuels. High FAME diesel fuel blends (B11-B30). Background to the parameters required and their respective limits and determination |
| DIN EN 16900 E : 2017 | FAST PYROLYSIS BIO-OILS FOR INDUSTRIAL BOILERS - REQUIREMENTS AND TEST METHODS |
| BS EN 61099:2010 | Insulating liquids. Specifications for unused synthetic organic esters for electrical purposes |
| I.S. EN 60422:2013 | MINERAL INSULATING OILS IN ELECTRICAL EQUIPMENT - SUPERVISION AND MAINTENANCE GUIDANCE (IEC 60422:2013 (EQV)) |
| I.S. EN 16709:2015 | AUTOMOTIVE FUELS - HIGH FAME DIESEL FUEL (B20 AND B30) - REQUIREMENTS AND TEST METHODS |
| 11/30239977 DC : 0 | BS EN 16245-2 - FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: ADDITIONAL REQUIREMENTS FOR RESINS, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| DIN EN 16245-2:2013-08 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| DIN EN 15322:2013-07 | Bitumen and bituminous binders - Framework for specifying cut-back and fluxed bituminous binders |
| DIN EN 45545-1:2013-08 | RAILWAY APPLICATIONS - FIRE PROTECTION ON RAILWAY VEHICLES - PART 1: GENERAL |
| 07/30170907 DC : DRAFT AUG 2007 | BS EN 15322 - BITUMEN AND BITUMINOUS BINDERS - FRAMEWORK FOR SPECIFYING CUT-BACK AND FLUXED BITUMINOUS BINDERS |
| PD CEN/TR 15367-3:2009 | Petroleum products. Guide for good housekeeping Prevention of cross contamination |
| 17/30361296 DC : DRAFT SEP 2017 | BS EN 16734 AMD 1 - AUTOMOTIVE FUELS - AUTOMOTIVE B10 DIESEL FUEL - REQUIREMENTS AND TEST METHODS |
| NF EN 14188-4 : 2011 | JOINT FILLERS AND SEALANTS - PART 4: SPECIFICATIONS FOR PRIMERS TO BE USED WITH JOINT SEALANTS |
| BS EN 14188-4:2009 | Joint fillers and sealants Specifications for primers to be used with joint sealants |
| BS EN 13924-1:2015 | Bitumen and bituminous binders. Specification framework for special paving grade bitumen Hard paving grade bitumens |
| 09/30202310 DC : 0 | BS EN 12514-2 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 2: SAFETY REQUIREMENTS AND TESTS - FEED PUMPS, CONTROL AND SAFETY DEVICES, SERVICE VESSELS |
| DIN EN 15940:2016-09 | AUTOMOTIVE FUELS - PARAFFINIC DIESEL FUEL FROM SYNTHESIS OR HYDROTREATMENT - REQUIREMENTS AND TEST METHODS |
| EN 590:2013 | Automotive fuels - Diesel - Requirements and test methods |
| I.S. EN 14188-4:2009 | JOINT FILLERS AND SEALANTS - PART 4: SPECIFICATIONS FOR PRIMERS TO BE USED WITH JOINT SEALANTS |
| DIN EN 590:2017-10 | Automotive fuels - Diesel - Requirements and test methods (includes Amendment :2017) |
| S.R. CWA 16379:2011 | FUELS AND BIOFUELS - PURE PLANT OIL FUEL FOR DIESEL ENGINE CONCEPTS - REQUIREMENTS AND TEST METHODS |
| DIN EN 14214:2014-06 | LIQUID PETROLEUM PRODUCTS - FATTY ACID METHYL ESTERS (FAME) FOR USE IN DIESEL ENGINES AND HEATING APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| BS EN 14156:2003 | Derivatives from coal pyrolysis. Coal tar based oils. Coal tar fuel. Specifications and test methods |
| I.S. EN 14023:2010 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR POLYMER MODIFIED BITUMENS |
| I.S. EN 13160-3:2016 | LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS |
| I.S. EN 12591:2009 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATIONS FOR PAVING GRADE BITUMENS |
| I.S. EN 13341:2005 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| DIN EN 12591:2009-08 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATIONS FOR PAVING GRADE BITUMENS |
| VDI 3397 Blatt 2:2014-06 | Maintenance of metalworking fluids for metalcutting and forming operations - Measures for maintaining quality, process improvement, and for reducing solid and liquid waste |
| S.R. CWA 15940:2009 | AUTOMOTIVE FUELS - PARAFFINIC DIESEL FROM SYNTHESIS OR HYDROTREATMENT - REQUIREMENTS AND TEST METHODS |
| DIN EN 13924-2:2014-07 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR SPECIAL PAVING GRADE BITUMEN - PART 2: MULTIGRADE PAVING GRADE BITUMENS |
| BS EN 60695-1-20:2016 | Fire hazard testing Guidance for assessing the fire hazard of electrotechnical products. Ignitability. General guidance |
| BS EN 60296:2012 | Fluids for electrotechnical applications. Unused mineral insulating oils for transformers and switchgear |
| DIN EN 13924-1:2016-02 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR SPECIAL PAVING GRADE BITUMEN - PART 1: HARD PAVING GRADE BITUMENS |
| DD CEN/TS 45545-7:2009 | Railway applications. Fire protection on railway vehicles Fire safety requirements for flammable liquid and flammable gas installations |
| 14/30298209 DC : 0 | BS EN 16734 - AUTOMOTIVE FUELS - AUTOMOTIVE B10 DIESEL FUEL - REQUIREMENTS AND TEST METHODS |
| 10/30216699 DC : 0 | BS EN 45545-7 - RAILWAY APPLICATIONS - FIRE PROTECTION ON RAILWAY VEHICLES - PART 7: FIRE SAFETY REQUIREMENTS FOR FLAMMABLE LIQUID AND FLAMMABLE GAS INSTALLATIONS |
| BS EN 15322:2013 | Bitumen and bituminous binders. Framework for specifying cut-back and fluxed bituminous binders |
| PREN 590 : DRAFT 2011 | AUTOMOTIVE FUELS - DIESEL - REQUIREMENTS AND TEST METHODS |
| 14/30310326 DC : 0 | BS EN 15940 - AUTOMOTIVE FUELS - PARAFFINIC DIESEL FUEL FROM SYNTHESIS OR HYDROTREATMENT - REQUIREMENTS AND TEST METHODS |
| I.S. EN 14214:2012 | LIQUID PETROLEUM PRODUCTS - FATTY ACID METHYL ESTERS (FAME) FOR USE IN DIESEL ENGINES AND HEATING APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| PREN 15322 : DRAFT 2011 | BITUMEN AND BITUMINOUS BINDERS - FRAMEWORK FOR SPECIFYING CUT-BACK AND FLUXED BITUMINOUS BINDERS |
| I.S. EN 16245-2:2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| I.S. EN 15940:2016 | AUTOMOTIVE FUELS - PARAFFINIC DIESEL FUEL FROM SYNTHESIS OR HYDROTREATMENT - REQUIREMENTS AND TEST METHODS |
| DIN EN 16900:2015-09 (Draft) | FAST PYROLYSIS BIO-OILS FOR INDUSTRIAL BOILERS - REQUIREMENTS AND TEST METHODS |
| CEI EN 60296 : 2013 | FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - UNUSED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEAR |
| EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| EN 14156:2003 | Derivatives from coal pyrolysis - Coal tar based oils: Coal tar fuel - Specifications and test methods |
| EN 14998:2005 | Derivatives from coal pyrolysis - Coal tar based oils: fluxings oils - Specifications and test methods |
| EN 14260:2003 | Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : road tars - Characteristics and test methods |
| EN 16245-2:2013 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| EN 14188-4:2009 | Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants |
| I.S. CEN TR 15367-3:2009 | PETROLEUM PRODUCTS - GUIDE FOR GOOD HOUSEKEEPING - PART 3: PREVENTION OF CROSS CONTAMINATION |
| BS EN 13924-2:2014 | Bitumen and bituminous binders. Specification framework for special paving grade bitumen Multigrade paving grade bitumens |
| CEN/TR 16557:2013 | Automotive fuels - High FAME diesel fuel blends (B11 - B30) - Background to the parameters required and their respective limits and determination |
| BS EN 16245-2:2013 | Fibre-reinforced plastic composites. Declaration of raw material characteristics Specific requirements for resin, curing systems, additives and modifiers |
| S.R. CEN/TR 17103:2017 | FAST PYROLYSIS BIO-OILS FOR STATIONARY INTERNAL COMBUSTION ENGINES - QUALITY DETERMINATION |
| BS EN 60422:2013 | Mineral insulating oils in electrical equipment. Supervision and maintenance guidance |
| PREN 14214 : DRAFT 2009 | AUTOMOTIVE FUELS - FATTY ACID METHYL ESTERS (FAME) FOR DIESEL ENGINES - REQUIREMENTS AND TEST METHODS |
| DIN EN 14188-4:2009-10 | Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants |
| 06/30147008 DC : 0 | EN 14188-4 - JOINT FILLERS AND SEALANTS - PART 4: SPECIFICATIONS FOR PRIMERS TO BE USED WITH JOINT SEALANTS |
| BS EN 60079-6:2007 | Explosive atmospheres Equipment protected by oil immersion \'o\' |
| 04/30117724 DC : DRAFT AUG 2004 | EN 14023 - BITUMEN AND BITUMINOUS BINDERS - FRAMEWORK SPECIFICATION FOR POLYMER MODIFIED BITUMENS |
| S.R. CEN/TR 16389:2017 | AUTOMOTIVE FUELS - PARAFFINIC DIESEL FUEL AND BLENDS WITH FAME - BACKGROUND TO THE PARAMETERS REQUIRED AND THEIR RESPECTIVE LIMITS AND DETERMINATION |
| S.R. CEN/TR 16557:2013 | AUTOMOTIVE FUELS - HIGH FAME DIESEL FUEL BLENDS (B11 - B30) - BACKGROUND TO THE PARAMETERS REQUIRED AND THEIR RESPECTIVE LIMITS AND DETERMINATION |
| 18/30369065 DC : DRAFT FEB 2018 | BS EN 14214 AMD 2 - LIQUID PETROLEUM PRODUCTS - FATTY ACID METHYL ESTERS (FAME) FOR USE IN DIESEL ENGINES AND HEATING APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 60836:2015 | SPECIFICATIONS FOR UNUSED SILICONE INSULATING LIQUIDS FOR ELECTROTECHNICAL PURPOSES |
| I.S. CEN/TR 15138:2005 | PETROLEUM PRODUCTS AND OTHER LIQUIDS - GUIDE TO FLASH POINT TESTING |
| I.S. EN 60695-1-20:2016 | FIRE HAZARD TESTING - PART 1-20: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - GENERAL GUIDANCE |
| S.R. CEN/TS 45545-7:2009 | RAILWAY APPLICATIONS - FIRE PROTECTION ON RAILWAY VEHICLES - PART 7: FIRE SAFETY REQUIREMENTS FOR FLAMMABLE LIQUID AND FLAMMABLE GAS INSTALLATIONS |
| DIN EN 14023:2013-04 | Bitumen and bituminous binders - Specification framework for polymer modified bitumens |
| BS EN 14023:2010 | Bitumen and bituminous binders. Specification framework for polymer modified bitumens |
| BS EN 14155:2003 | Derivatives from coal pyrolysis. Carbon black feedstock. Specifications and test methods |
| BS EN 13341 : 2005 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| EN 14264:2003 | Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : impregnating pitch - Characteristics and test methods |
| EN 14023:2010 | Bitumen and bituminous binders - Specification framework for polymer modified bitumens |
| EN 14733:2005+A1:2010 | Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control |
| EN 13924-1:2015 | Bitumen and bituminous binders - Specification framework for special paving grade bitumen - Part 1: Hard paving grade bitumens |
| EN 14155:2003 | Derivatives from coal pyrolysis - Carbon black feedstock - Specifications and test methods |
| EN 13991:2003 | Derivatives from coal pyrolysis - Coal tar based oils: creosotes - Specifications and test methods |
| EN 15322:2013 | Bitumen and bituminous binders - Framework for specifying cut-back and fluxed bituminous binders |
| EN 13924-2:2014 | Bitumen and bituminous binders - Specification framework for special paving grade bitumen - Part 2: Multigrade paving grade bitumens |
| EN 16900:2017 | Fast pyrolysis bio-oils for industrial boilers - Requirements and test methods |
| I.S. EN 45545-1:2013 | RAILWAY APPLICATIONS - FIRE PROTECTION ON RAILWAY VEHICLES - PART 1: GENERAL |
| 11/30250572 DC : 0 | BS EN 15322 - BITUMEN AND BITUMINOUS BINDERS - FRAMEWORK FOR SPECIFYING CUT-BACK AND FLUXED BITUMINOUS BINDERS |
| PD CEN/TR 15138:2005 | Petroleum products and other liquids. Guide to flash point testing |
| I.S. EN 16900:2017 | FAST PYROLYSIS BIO-OILS FOR INDUSTRIAL BOILERS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 13924:2006 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATIONS FOR HARD PAVING GRADE BITUMENS |
| PREN 13160-3 : DRAFT 2014 | LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS |
| I.S. EN 13924-2:2014 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR SPECIAL PAVING GRADE BITUMEN - PART 2: MULTIGRADE PAVING GRADE BITUMENS |
| 11/30247867 DC : 0 | BS EN 13924-2 - BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR SPECIAL BITUMEN - PART 2: MULTIGRADE BITUMENOUS BINDERS |
| 11/30249539 DC : 0 | BS EN 590 - AUTOMOTIVE FUELS - DIESEL - REQUIREMENTS AND TEST METHODS |
| 05/30138350 DC : DRAFT AUG 2005 | EN 15322 - BITUMEN AND BITUMINOUS BINDERS - FRAMEWORK FOR SPECIFYING CUTBACK AND FLUXED BITUMINOUS BINDERS |
| I.S. EN 16734:2016 | AUTOMOTIVE FUELS - AUTOMOTIVE B10 DIESEL FUEL - REQUIREMENTS AND TEST METHODS |
| 15/30325842 DC : 0 | BS EN 16900 - FAST PYROLYSIS BIO-OILS FOR INDUSTRIAL BOILERS - REQUIREMENTS AND TEST METHODS |
| 13/30255316 DC : 0 | BS EN 13924-1 - BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR SPECIAL PAVING GRADE BITUMEN - PART 1: HARD PAVING GRADE BITUMENS |
| CEI EN 60079-6 : 2016 | EXPLOSIVE ATMOSPHERES - PART 6: EQUIPMENT PROTECTION BY LIQUID IMMERSION 'O' |
| 03/110060 DC : 0 | BS EN 45545-7 - RAILWAY APPLICATIONS - FIRE PROTECTION OF RAILWAY VEHICLES - PART 7: FIRE SAFETY REQUIREMENTS FOR FLAMMABLE LIQUID AND FLAMMABLE GAS INSTALLATIONS |
| CLC/TR 50503:2010 | Guidelines for the inventory control, management, decontamination and/or disposal of electrical equipment and insulating liquids containing PCBs |
| CEN/TR 15367-3:2009 | Petroleum products - Guide for good housekeeping - Part 3: Prevention of cross contamination |
| PREN 12591 : DRAFT 2016 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATIONS FOR PAVING GRADE BITUMENS |
| I.S. EN 60296:2012 | FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - UNUSED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEAR (IEC 60296:2012 (EQV)) |
| I.S. EN 60079-6:2015 | EXPLOSIVE ATMOSPHERES - PART 6: EQUIPMENT PROTECTION BY LIQUID IMMERSION 'O' |
| I.S. EN 590:2013+A1:2017&LC:2017 | AUTOMOTIVE FUELS - DIESEL - REQUIREMENTS AND TEST METHODS |
| I.S. EN 13924-1:2015 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR SPECIAL PAVING GRADE BITUMEN - PART 1: HARD PAVING GRADE BITUMENS |
| DIN EN 16709:2015-12 | AUTOMOTIVE FUELS - HIGH FAME DIESEL FUEL (B20 AND B30) - REQUIREMENTS AND TEST METHODS |
| BS EN 590 : 2013 | AUTOMOTIVE FUELS - DIESEL - REQUIREMENTS AND TEST METHODS |
| I.S. EN 61099:2010 | INSULATING LIQUIDS - SPECIFICATIONS FOR UNUSED SYNTHETIC ORGANIC ESTERS FOR ELECTRICAL PURPOSES |
| EN 45545-1 : 2013 COR 2013 | RAILWAY APPLICATIONS - FIRE PROTECTION ON RAILWAY VEHICLES - PART 1: GENERAL |
| BS EN 14260:2003 | Derivatives from coal pyrolysis. Coal tar and pitch based binders and related products. Road tars. Characteristics and test methods |
| BS EN 13160-3:2003 | Leak detection systems Liquid systems for tanks |
| BS EN 13924:2006 | Bitumen and bituminous binders. Specifications for hard paving grade bitumens |
| DIN EN 14264:2003-12 | Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products: Impregnating pitch - Characteristics and test methods; German version EN 14264:2003 |
| EN 12591:2009 | Bitumen and bituminous binders - Specifications for paving grade bitumens |
| CEN/TR 17103:2017 | Petroleum and related products - Fast pyrolysis bio-oils for stationary internal combustion engines - Quality determination |
| DIN EN 14214:2003-11 | LIQUID PETROLEUM PRODUCTS - FATTY ACID METHYL ESTERS (FAME) FOR USE IN DIESEL ENGINES AND HEATING APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| DIN EN 14156:2003-11 | DERIVATIVES FROM COAL PYROLYSIS - COAL TAR BASED OILS: COAL TAR FUEL - SPECIFICATIONS AND TEST METHODS |
| CEN/TR 16389:2017 | Automotive fuels - Paraffinic diesel fuel and blends with FAME - Background to the parameters required and their respective limits and determination |
| DIN EN 14155:2003-11 | DERIVATIVES FROM COAL PYROLYSIS - CARBON BLACK FEEDSTOCK - SPECIFICATIONS AND TEST METHODS |
| CEN/TS 15940:2012 | Automotive fuels - Paraffinic diesel fuel from synthesis or hydrotreatment - Requirements and test methods |
| DIN EN 14733:2010-12 | BITUMEN AND BITUMINOUS BINDERS - BITUMINOUS EMULSIONS, FLUXED AND CUT-BACK BITUMEN FACTORY PRODUCTION CONTROL |
| DIN EN 13924:2006-07 | BITUMEN AND BITUMINOUS BINDERS - SPECIFICATIONS FOR HARD PAVING GRADE BITUMENS |
| DIN EN 14260:2003-12 | Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products: Road tars - Characteristics and test methods; German version EN 14260:2003 |
| EN 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| EN 60836:2015 | Specifications for unused silicone insulating liquids for electrotechnical purposes |
| EN 60422:2013 | Mineral insulating oils in electrical equipment - Supervision and maintenance guidance |
| EN 60695-1-20:2016 | Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance |
| UNE-EN 14188-4:2010 | Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants |
| I.S. EN 14733:2005 | BITUMEN AND BITUMINOUS BINDERS - BITUMINOUS EMULSIONS, FLUXED AND CUT-BACK BITUMEN FACTORY PRODUCTION CONTROL |
| UNE-EN 45545-1:2013 | Railway applications - Fire protection on railway vehicles - Part 1: General |
| UNE-EN 16709:2016 | Automotive fuels - High FAME diesel fuel (B20 and B30) - Requirements and test methods |
| UNE-EN 15322:2014 | Bitumen and bituminous binders - Framework for specifying cut-back and fluxed bituminous binders |
| UNE-EN 15940:2016 | Automotive fuels - Paraffinic diesel fuel from synthesis or hydrotreatment - Requirements and test methods |
| UNE-EN 16900:2017 | Fast pyrolysis bio-oils for industrial boilers - Requirements and test methods |
| UNE-EN 60695-1-20:2016 | Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance |
| UNE-EN 60422:2013 | Mineral insulating oils in electrical equipment - Supervision and maintenance guidance |
| UNE-EN 16245-2:2014 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| UNE-EN 60836:2015 | Specifications for unused silicone insulating liquids for electrotechnical purposes |
| UNE-EN 60079-6:2016 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| UNE-EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| UNE-EN 14733:2006 | Bitumen and bituminous binders - Bituminous emulsions, fluxed and cut-back bitumen factory production control |
| UNE-EN 61099:2011 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| UNE-EN 13160-3:2017 | Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks |
| UNE-EN 14214:2013 | Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods |
| UNE-EN 16734:2017 | Automotive fuels - Automotive B10 diesel fuel - Requirements and test methods |
| CEI EN 60422 : 2014 | MINERAL INSULATING OILS IN ELECTRICAL EQUIPMENT - SUPERVISION AND MAINTENANCE GUIDANCE |
| I.S. EN 13991:2003 | DERIVATIVES FROM COAL PYROLYSIS - COAL TAR BASED OILS: CREOSOTES - SPECIFICATIONS AND TEST METHODS |
| ISO 3171:1988 | Petroleum liquids — Automatic pipeline sampling |
| ISO/TR 29662:2009 | Petroleum products and other liquids — Guidance for flash point testing |
| ISO 3170:2004 | Petroleum liquids — Manual sampling |
| CEN/TR 15138:2005 | Petroleum products and other liquids - Guide to flash point testing |
| ISO Guide 33:2015 | Reference materials — Good practice in using reference materials |
| ISO Guide 35:2017 | Reference materials — Guidance for characterization and assessment of homogeneity and stability |
| ASTM E 2251 : 2014 : REDLINE | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ISO 3679:2015 | Determination of flash no-flash and flash point — Rapid equilibrium closed cup method |
| ISO 15528:2013 | Paints, varnishes and raw materials for paints and varnishes — Sampling |
| ISO 1523:2002 | Determination of flash point — Closed cup equilibrium method |
| ISO 4259:2006 | Petroleum products — Determination and application of precision data in relation to methods of test |
| IEC 60751:2008 | Industrial platinum resistance thermometers and platinum temperature sensors |
| ISO 1513:2010 | Paints and varnishes — Examination and preparation of test samples |
| ISO 13736:2013 | Determination of flash point — Abel closed-cup method |
| ISO Guide 34:2009 | General requirements for the competence of reference material producers |
| ASTM E 1137 : 1997 | Standard Specification for Industrial Platinum Resistance Thermometers |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Sorry this product is not available in your region.