I.S. EN 1092-1:2007
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES,FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 1: STEEL FLANGES
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2007
Publisher
Superseded date
06-12-2018
Superseded by
Excluding VAT
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 General requirements
Annex A (normative) - Wall thickness and end preparation
for flanges type 11, 34, 35, 36, 37 and pipe nominal
thicknesses for the use with type 01 flanges
Annex B (informative) - Material groups
Annex C (informative) - Approximate masses of flanges
and collars
Annex D (informative) - Additional materials
Annex E (normative) - Basis of flange calculation
Annex F (normative) - Determination of p/T ratings
Annex G (normative) - p/T ratings for a selection of EN
materials
Annex H (informative) - Rings for flanges with groove
Annex I (informative) - Flanges with fixed inner diameter
Annex J (informative) - Mating dimensions for flanges
with higher DN
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 2014/68/EU Pressure Equipment
Directive aimed to be covered
Bibliography
Defines the flange types and their facings, dimensions, tolerances, threading, bolt sizes, flange jointing face surface finish, marking, materials, pressure/temperature ratings and approximate flange masses.
| DocumentType |
Standard
|
| Pages |
130
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 1092-1 : 2007 | Identical |
| NF EN 1092-1 : 2007 + A1 2013 | Identical |
| ONORM EN 1092-1 : JUL 2014 | Identical |
| NS EN 1092-1 : 2007 AC 2014 | Identical |
| DIN EN 1092-1:2016-05 (Draft) | Identical |
| NBN EN 1092-1 : 2007 COR 2014 | Identical |
| EN 1092-1:2007 | Equivalent |
| DIN EN 1092-1:2007-11 | Equivalent |
| EN 1092-1:2018 | Identical |
| UNE-EN 1092-1:2008 | Identical |
| NEN EN 1092-1 : 2018 | Identical |
| I.S. 820:2010 | NON-DOMESTIC GAS INSTALLATIONS |
| ISO 17636-1:2013 | Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray techniques with film |
| EN ISO 9692-1:2013 | Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013) |
| EN 1514-1:1997 | Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts |
| EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
| CEN/TS 1591-3:2007 | Flanges and their joints - Design rules for gasketed circular flange connections - Part 3: Calculation method for metal to metal contact type flanged joint |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| EN ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005) |
| EN 1591-1:2013 | Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation |
| EN 1708-1:2010 | Welding - Basic welded joint details in steel - Part 1: Pressurized components |
| EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| ISO 15614-13:2012 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 13: Upset (resistance butt) and flash welding |
| ISO 11666:2010 | Non-destructive testing of welds — Ultrasonic testing — Acceptance levels |
| EN ISO 3452-1:2013 | Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, Corrected version 2014-05-01) |
| EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| ISO 23277:2015 | Non-destructive testing of welds — Penetrant testing — Acceptance levels |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| ISO 9712:2012 | Non-destructive testing — Qualification and certification of NDT personnel |
| EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
| EN ISO 10675-1:2016 | Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 1: Steel, nickel, titanium and their alloys (ISO 10675-1:2016) |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| ISO 14732:2013 | Welding personnel — Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials |
| EN 1759-4:2003 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| DIN 17102:1983-10 | WELDABLE NORMALIZED FINE GRAIN STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS FOR PLATE, STRIP, WIDE FLATS, SECTIONS AND BARS |
| EN ISO 23278 | Non-destructive testing of welds - Magnetic particle testing - Acceptance levels (ISO 23278:2015) |
| ISO 9606-1:2012 | Qualification testing of welders — Fusion welding — Part 1: Steels |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN ISO 23277:2015 | Non-destructive testing of welds - Penetrant testing - Acceptance levels (ISO 23277:2015) |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| EN ISO 4014:2011 | Hexagon head bolts - Product grades A and B (ISO 4014:2011) |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| ISO 6708:1995 | Pipework components — Definition and selection of DN (nominal size) |
| EN ISO 14732:2013 | Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013) |
| ISO 887:2000 | Plain washers for metric bolts, screws and nuts for general purposes — General plan |
| ISO 23278:2015 | Non-destructive testing of welds — Magnetic particle testing — Acceptance levels |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| DIN 1681:1985-06 | CAST STEELS FOR GENERAL PURPOSES - TECHNICAL DELIVERY CONDITIONS |
| EN ISO 9712:2012 | Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
| ISO 17640:2017 | Non-destructive testing of welds — Ultrasonic testing — Techniques, testing levels, and assessment |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| EN ISO 1127:1996 | Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| ISO 3452-1:2013 | Non-destructive testing — Penetrant testing — Part 1: General principles |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
| EN 1515-2:2001 | Flanges and their joints - Bolting - Part 2: Classification of bolt materials for steel flanges, PN designated |
| EN 10217-7:2014 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 13480-3:2017 | Metallic industrial piping - Part 3: Design and calculation |
| EN 1514-2:2014 | Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| EN ISO 17637:2016 | Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation |
| EN 10222-3:2017 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
| ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive quality requirements |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 10021:2006 | General technical delivery conditions for steel products |
| ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
| ISO 17636-2:2013 | Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray techniques with digital detectors |
| EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| EN 1515-4:2009 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
| EN 1333:2006 | Flanges and their joints - Pipework components - Definition and selection of PN |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| CEN ISO/TR 15608:2017 | Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2017) |
| EN 1591-2:2008 | Flanges and their joints - Design rules for gasketed circular flange connections - Part 2: Gasket parameters |
| ISO 17637:2016 | Non-destructive testing of welds — Visual testing of fusion-welded joints |
| EN 10226-3:2005 | Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges |
| EN ISO 17636-2:2013 | Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013) |
| EN ISO 15614-13:2012 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2012) |
| EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
| ISO 9692-2:1998 | Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials — General rules |
| EN ISO 17636-1:2013 | Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2013) |
| EN ISO 9606-1:2017 | Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013) |
| EN ISO 17638:2016 | Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2016) |
| EN 10220:2002 | Seamless and welded steel tubes - Dimensions and masses per unit length |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| ISO 10675-1:2016 | Non-destructive testing of welds — Acceptance levels for radiographic testing — Part 1: Steel, nickel, titanium and their alloys |
| EN 764-3:2002 | Pressure equipment - Part 3: Definition of parties involved |
| ISO 17638:2016 | Non-destructive testing of welds — Magnetic particle testing |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN 10216-3:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes |
| ISO 4014:2011 | Hexagon head bolts — Product grades A and B |
| ISO 1127:1992 | Stainless steel tubes — Dimensions, tolerances and conventional masses per unit length |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.