I.S. EN 62132-4:2006
Current
The latest, up-to-date edition.
INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC IMMUNITY 150 KHZ TO 1 GHZ - PART 4: DIRECT RF POWER INJECTION METHOD
Hardcopy , PDF
English
01-01-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 General
4.1 Measurement basics
4.2 Single pin direct power injection
4.3 Multiple pin direct power injection into
pins of differential mode systems
5 Test conditions
6 Test equipment
6.1 General
6.2 RF power source
6.3 RF power meter and directional coupler
7 Test set-up
7.1 General
7.2 Power injection set-up
7.3 Test circuit board
7.4 Characteristics of the power injection set-up
7.5 Decoupling networks
8 Test procedure
8.1 General
8.2 Specific test procedure
9 Test report
Annex A (informative) Example of a specification of immunity
levels e.g. for automotive applications
Annex B (informative) Hints for the best installation of a
test set-up with respect to RF
Annex C (informative) Constant peak test level explanation
Annex ZA (normative) Normative references to international
publications with their corresponding
European publications
Bibliography
Specifies a method to measure the immunity of integrated circuits (IC) in the presence of conducted RF disturbances, e.g. resulting from radiated RF disturbances.
DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
DocumentType |
Standard
|
Pages |
64
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Current
|
Standards | Relationship |
IEC 62132-4:2006 | Identical |
DIN EN 62132-4:2006-10 | Identical |
BS EN 62132-4:2006 | Identical |
NF EN 62132-4 : 2006 | Identical |
SN EN 62132-4 : 2006 | Identical |
NBN EN 62132-4 : 2007 | Identical |
EN 62132-4:2006 | Identical |
ISO 11452-3:2016 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 3: Transverse electromagnetic (TEM) cell |
ISO 11452-4:2011 | Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 4: Harness excitation methods |
ISO 11451-3:2015 | Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 3: On-board transmitter simulation |
EN 62132-1:2016 | Integrated circuits - Measurement of electromagnetic immunity - Part 1: General conditions and definitions |
IEC 62132-1:2015 | Integrated circuits - Measurement of electromagnetic immunity - Part 1: General conditions and definitions |
ISO 11898-1:2015 | Road vehicles — Controller area network (CAN) — Part 1: Data link layer and physical signalling |
EN 61967-4 : 2002 COR 2017 | INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 4: MEASUREMENT OF CONDUCTED EMISSIONS - 1 OHM/150 OHM DIRECT COUPLING METHOD (IEC 61967-4:2002/COR1:2017) |
IEC 61967-4:2002+AMD1:2006 CSV | Integrated circuits - Measurement of electromagnetic emissions, 150 kHz to 1 GHz - Part 4: Measurement of conducted emissions - 1 Ω/150 Ω direct coupling method |
ISO 11452-2:2004 | Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 2: Absorber-lined shielded enclosure |
ISO 11452-1:2015 | Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 1: General principles and terminology |
ISO 11452-5:2002 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 5: Stripline |
ISO 11451-2:2015 | Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 2: Off-vehicle radiation sources |
ISO 11452-7:2003 | Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 7: Direct radio frequency (RF) power injection |
ISO 11451-4:2013 | Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 4: Bulk current injection (BCI) |
ISO 11451-1:2015 | Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 1: General principles and terminology |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.