I.S. EN ISO 898-1:2013
Current
The latest, up-to-date edition.
MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 1: BOLTS, SCREWS AND STUDS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD (ISO 898-1:2013)
Hardcopy , PDF
English
01-01-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Designation system for property classes
6 Materials
7 Mechanical and physical properties
8 Applicability of test methods
9 Test methods
10 Marking
Annex A (informative) - Relationship between tensile
strength and elongation after fracture
Annex B (informative) - Influence of elevated temperatures
on mechanical properties of fasteners
Annex C (informative) - Elongation after fracture for
full-size fasteners, A[F]
Bibliography
Describes mechanical and physical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10 degrees C to 35 degrees C.
DevelopmentNote |
Supersedes I.S. EN 20898-1. (11/2006)
|
DocumentType |
Standard
|
Pages |
69
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Current
|
Supersedes |
Standards | Relationship |
NBN EN ISO 898-1 : 2013 | Identical |
UNE-EN ISO 898-1:2015 | Identical |
BS EN ISO 898-1:2013 | Identical |
ISO 898-1:2013 | Identical |
EN ISO 898-1:2013 | Identical |
DIN EN ISO 898-1:2013-05 | Identical |
NEN EN ISO 898-1 : 2013 | Identical |
UNI EN ISO 898-1 : 2013 | Identical |
NF EN ISO 898-1 : 2013 | Identical |
NS EN ISO 898-1 : 2013 AC 2013 | Identical |
ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
ISO 898-7:1992 | Mechanical properties of fasteners Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm |
ISO 10683:2014 | Fasteners Non-electrolytically applied zinc flake coatings |
ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
ISO 10684:2004 | Fasteners — Hot dip galvanized coatings |
ISO 4042:1999 | Fasteners Electroplated coatings |
ISO 6157-3:1988 | Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements |
ISO 6157-1:1988 | Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements |
ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
ISO 4885:2017 | Ferrous materials Heat treatments Vocabulary |
ISO 16426:2002 | Fasteners — Quality assurance system |
ISO 965-2:1998 | ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality |
ISO 225:2010 | Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions |
ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners with specified hardness classes Coarse thread and fine pitch thread |
ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
ISO 965-4:1998 | ISO general purpose metric screw threads Tolerances Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing |
ISO 68-1:1998 | ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads |
ISO 273:1979 | Fasteners — Clearance holes for bolts and screws |
ISO 261:1998 | ISO general purpose metric screw threads — General plan |
ISO 965-1:2013 | ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data |
ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
ISO 1891:2009 | Fasteners — Terminology |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.