IEC 62752:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
27-03-2024
English - French, Spanish, Castilian
04-03-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Characteristics of IC-CPDs
6 Marking and other product information
7 Standard conditions for operation in service
and for installation
8 Requirements for construction and operation
9 Tests
Annex A (normative) - Test sequences and number
of samples to be submitted for verification
of conformity to this standard
Annex B (normative) - Routine tests
Annex C (normative) - Determination of clearances
and creepage distances
Annex D (informative) - Switched-protective conductor
application
Annex E (informative) - Example of IC-CPD for mode
2 charging
Annex F (informative) - Types of IC-CPD according
to construction and assembly
Annex G (informative) - Methods for determination
of short-circuit power factor
Bibliography
IEC 62752:2016 applies to in-cable control and protection devices (IC-CPDs) for mode 2 charging of electric road vehicles, hereafter referred to as IC-CPD including control and safety functions. This standard applies to portable devices performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value.
The contents of the corrigendum of February 2019 have been included in this copy.
| DevelopmentNote |
Stability date: 2018. (03/2016)
|
| DocumentType |
Standard
|
| Pages |
327
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 62752 : 2016 | Identical |
| NEN EN IEC 62752 : 2016 | Identical |
| PN EN 62752 : 2016 | Identical |
| VDE 0666-10 : 2017 | Identical |
| DIN EN 62752 : 2017 | Identical |
| IS 17120 : 2019 | Identical |
| UNE-EN 62752:2017 | Identical |
| CEI EN 62752 : 1ED 2017 | Identical |
| EN 62752:2016 | Identical |
| DS EN 62752 : 2016 | Identical |
| BS EN 62752:2016 | Identical |
| IEC 61851-1:2017 | Electric vehicle conductive charging system - Part 1: General requirements |
| IEC 62196-1:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements |
| BS EN 62196-1:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles General requirements |
| VDI 2166 Blatt 2:2015-10 | Planning of electrical installations in buildings - Advice for electric mobility |
| EN 62196-1:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements |
| I.S. EN 62196-1:2014 | PLUGS, SOCKET-OUTLETS, VEHICLE CONNECTORS AND VEHICLE INLETS - CONDUCTIVE CHARGING OF ELECTRIC VEHICLES - PART 1: GENERAL REQUIREMENTS |
| CEI EN IEC 61543:2023 | Residual current-operated protective devices (RCDs) for household and similar use. Electromagnetic compatibility |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 62423:2009 | Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses |
| IEC 60068-2-5:2010 | Environmental testing - Part 2-5: Tests - Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing |
| ISO 16750-4:2010 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 4: Climatic loads |
| IEC 61540:1997+AMD1:1998 CSV | Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs) |
| ISO 16750-5:2010 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 5: Chemical loads |
| IEC 62196-2:2016 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC TS 62763:2013 | Pilot function through a control pilot circuit using PWM (pulse width modulation) and a control pilot wire |
| IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV | Plugs and socket-outlets for household and similar purposes - Part1: General requirements |
| IEC GUIDE 117:2010 | Electrotechnical equipment - Temperatures of touchable hot surfaces |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV | Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules |
| IEC 61543:1995 | Residual current-operated protective devices (RCDs) for household and similar use - Electromagnetic compatibility |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| IEC 62335:2008 | Circuit breakers - Switched protective earth portable residual current devices for class I and battery powered vehicle applications |
| IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
| IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV | Low-voltage fuses - Part 1: General requirements |
| IEC 60068-2-31:2008 | Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens |
| IEC 60068-2-64:2008 | Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance |
| IEC 60364-7-722:2015 | Low-voltage electrical installations - Part 7-722: Requirements for special installations or locations - Supplies for electric vehicles |
| IEC 60999-1:1999 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 16750-3:2012 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 3: Mechanical loads |
| IEC TR 60755:2008 | General requirements for residual current operated protective devices |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60364-4-44:2007+AMD1:2015 CSV | Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances |
| IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
| ISO 17409:2015 | Electrically propelled road vehicles Connection to an external electric power supply Safety requirements |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 60068-3-4:2001 | Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
| IEC 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| ISO 178:2010 | Plastics Determination of flexural properties |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 61851-1:2017 | Electric vehicle conductive charging system - Part 1: General requirements |
| IEC 60309-2:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories |
| IEC 62196-1:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.