IEEE 404-2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
IEEE Standard for Extruded and Laminated Dielectric Shielded Cable Joints Rated 2.5 kV to 500 kV
21-03-2023
English
18-06-2012
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. Overview
2. Normative references
3. Definitions
4. Service conditions
5. Ratings
6. General requirements
7. Design testing
8. Routine production testing
Annex A (informative) - Typical values of heat-shrinkable
and multi-component cold-shrink joint component
tests and sampling rates
Annex B (informative) - Typical values of elastomeric
taped joint component tests and sampling rates
Annex C (informative) - DC test voltage reference
Annex D (informative) - Bibliography
Sets up electrical ratings and test requirements of cable joints used with extruded and laminated dielectric shielded cables rated in preferred voltage steps from 2.5 kV to 500 kV. Also specifies test requirements for joint jacket seal devices and joint metallic-shield devices.
| Committee |
Insulated Conductors
|
| DevelopmentNote |
Supersedes IEEE DRAFT 404. (03/2007)
|
| DocumentType |
Standard
|
| ISBN |
978-0-7381-7267-5
|
| Pages |
46
|
| PublisherName |
Institute of Electrical & Electronics Engineers
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| CSA C22.2 No. 241 : 0 | Identical |
| IEEE 141 : 1993 | IEEE Recommended Practice for Electric Power Distribution for Industrial Plants |
| IEEE 592-2007 REDLINE | IEEE Standard for Exposed Semiconducting Shields on High-Voltage Cable Joints and Separable Connectors |
| IEEE 1242-1999 | IEEE Guide for Specifying and Selecting Power, Control, and Special-Purpose Cable for Petroleum and Chemical Plants |
| IEEE DRAFT 1511 : D6.0 MAY 2000 | DRAFT GUIDE FOR INVESTIGATING AND ANALYZING POWER CABLE, JOINT, AND TERMINATION FAILURES ON SYSTEMS RATED 5 KV THROUGH 46 KV |
| IEEE 525-2007 | IEEE Guide for the Design and Installation of Cable Systems in Substations |
| IEEE 400.1-2007 | IEEE Guide for Field Testing of Laminated Dielectric, Shielded Power Cable Systems Rated 5 kV and Above with High Direct Current Voltage |
| TM 5-811-1 : V19950228 | ARMY TECHNICAL MANUAL - ELECTRICAL POWER SUPPLY AND DISTRIBUTION |
| IEEE DRAFT 525 : D15 2006 | DESIGN AND INSTALLATION OF CABLE SYSTEMS IN SUBSTATIONS |
| IEEE 400-2012 REDLINE | IEEE Guide for Field Testing and Evaluation of the Insulation of Shielded Power Cable Systems Rated 5 kV and Above |
| IEEE DRAFT 400.1 : D8 2006 | FIELD TESTING OF LAMINATED DIELECTRIC, SHIELDED POWER CABLE SYSTEMS RATED 5 KV AND ABOVE WITH HIGH DIRECT CURRENT VOLTAGE |
| IEEE 1816-2013 | IEEE Guide for Preparation Techniques of Extruded Dielectric, Shielded Cables Rated 2.5 kV through 46 kV and the Installation of Mating Accessories |
| IEEE 3001.5-2013 | IEEE Recommended Practice for the Application of Power Distribution Apparatus in Industrial and Commercial Power Systems |
| CSA C22.2 No. 272 : 2014 | WIND TURBINE ELECTRICAL SYSTEMS |
| CSA C22.3 No. 7 : 2015 | UNDERGROUND SYSTEMS |
| IEEE 241 : 1990 | ELECTRIC POWER SYSTEMS IN COMMERCIAL BUILDINGS |
| IEEE 400.4-2015 | IEEE Guide for Field Testing of Shielded Power Cable Systems Rated 5 kV and Above with Damped Alternating Current (DAC) Voltage |
| IEEE 1313.1-1996 | IEEE Standard for Insulation Coordination - Definitions, Principles and Rules |
| IEEE 82 : 2002 | TEST PROCEDURE FOR IMPULSE VOLTAGE TESTS ON INSULATED CONDUCTORS |
| IEEE 592-2018 | IEEE Standard for Insulation Shields on Medium-Voltage (15 kV - 35 kV) Cable Joints and Separable Connectors |
| ASTM D 4325 : 2013 : REDLINE | Standard Test Methods for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes |
| ASTM D 4496 : 2013 | Standard Test Method for D-C Resistance or Conductance of Moderately Conductive Materials |
| ASTM D 4388 : 2013 | Standard Specification for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes |
| IEEE 4-1995 | IEEE Standard Techniques for High-Voltage Testing |
| IEC 60502-4:2010 | Power cables with extruded insulation and their accessories for rated voltages from 1 kV (U<sub>m</sub> = 1,2 kV) up to 30 kV (U<sub>m</sub> = 36 kV) - Part 4: Test requirements on accessories for cables with rated voltages from 6 kV (U<sub>m</sub> = 7,2 kV) up to 30 kV (U<sub>m</sub> = 36 kV) |
| IEEE 575-1988 | IEEE Guide for Application of Sheath-Bonding Methods for Single-Conductor Cables and the Calculation of Induced Voltages and Currents in Cable Sheaths |
| IEEE 592-2007 REDLINE | IEEE Standard for Exposed Semiconducting Shields on High-Voltage Cable Joints and Separable Connectors |
| IEEE 82 : 2002 | TEST PROCEDURE FOR IMPULSE VOLTAGE TESTS ON INSULATED CONDUCTORS |
| IEEE 4-2013 | IEEE Standard for High-Voltage Testing Techniques |
| IEEE C37.09-1999 | IEEE Standard Test Procedure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis |
| IEEE 575-2014 | IEEE Guide for Bonding Shields and Sheaths of Single-Conductor Power Cables Rated 5 kV through 500 kV |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.