IEEE 45.6-2016
Current
Current
The latest, up-to-date edition.
IEEE Recommended Practice for Electrical Installations on Shipboard--Electrical Testing
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
03-03-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. Overview
2. Normative references
3. Definitions
4. General
5. New installations
6. Existing installations
Annex A (informative) - Bibliography
The recommendations for electrical testing for power generation, distribution, and electric propulsion systems installed shipboards are established by this document.
| Committee |
Petroleum and Chemical Industry
|
| DocumentType |
Standard
|
| ISBN |
978-1-5044-3615-1
|
| Pages |
39
|
| ProductNote |
THIS STANDARD ALSO REFERS TO IEC 60034-27,IEC 60947,IEC 61934,IEEE P45.1,MIL-R26,
|
| PublisherName |
Institute of Electrical & Electronics Engineers
|
| Status |
Current
|
| IEEE 45.3-2015 | IEEE Recommended Practice for Shipboard Electrical Installations -- Systems Engineering |
| IEC 60060-2:2010 | High-voltage test techniques - Part 2: Measuring systems |
| IEC 62271-100:2008+AMD1:2012+AMD2:2017 CSV | High-voltage switchgear and controlgear - Part 100: Alternating-current circuit-breakers |
| CSA C22.2 No. 2 : 56(R1969) | ELECTRIC SIGNS |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| IEEE C37.20.1-2015 | IEEE Standard for Metal-Enclosed Low-Voltage (1000 Vac and below, 3200 Vdc and below) Power Circuit Breaker Switchgear |
| IEC 62271-106:2011 | High-voltage switchgear and controlgear - Part 106: Alternating current contactors, contactor-based controllers and motor-starters |
| ICEA T 26 465 : 2012 | GUIDE FOR FREQUENCY OF SAMPLING EXTRUDED DIELECTRIC POWER, CONTROL, INSTRUMENTATION, AND PORTABLE CABLES FOR TEST |
| CSA C22 NO. 4 : 2016 | ENCLOSED AND DEAD-FRONT SWITCHES |
| IEC 62271-200:2011 | High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
| IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
| NEMA MG 1 : 2016 | MOTORS AND GENERATORS |
| CSA C22.2 No. 5 : 2013 | MOLDED-CASE CIRCUIT BREAKERS, MOLDED-CASE SWITCHES AND CIRCUIT-BREAKER ENCLOSURES |
| CSA C22.2 No. 1 : 2004 | AUDIO, VIDEO AND SIMILAR ELECTRONIC EQUIPMENT |
| IEC 61960:2011 | Secondary cells and batteries containing alkaline or other non-acid electrolytes - Secondary lithium cells and batteries for portable applications |
| IEEE 841-2009 | IEEE Standard for Petroleum and Chemical Industry--Premium-Efficiency, Severe-Duty, Totally Enclosed Fan-Cooled (TEFC) Squirrel Cage Induction Motors--Up to and Including 370 kW (500 hp) |
| IEEE 1106-2015 | IEEE Recommended Practice for Installation, Maintenance, Testing, and Replacement of Vented Nickel-Cadmium Batteries for Stationary Applications |
| IEEE C37.20.2-2015 | IEEE Standard for Metal-Clad Switchgear |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| CSA C22.2 No. 7 : 38(R1949) | PORTABLE ELECTRIC DISPLAYS AND INCANDESCENT LAMP SIGNS |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| IEEE 45.8-2016 | IEEE Recommended Practice for Electrical Installations on Shipboard--Cable Systems |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| ANSI/NEMA WC 54/ICEA T-26-465:2013 | Guide for Frequency of Sampling Extruded Dielectric Power, Control, Instrumentation and Portable Cables for Test |
| IEEE 1580-2010 | IEEE Recommended Practice for Marine Cable for Use on Shipboard and Fixed or Floating Facilities |
| IEEE 113-1985 | IEEE Guide: Test Procedures for Direct-Current Machines |
| IEC 60034-2-1:2014 | Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) |
| UL 1309:3ED 2017-04-21 | Marine Shipboard Cable |
| NFPA 70E : 2018 | ELECTRICAL SAFETY IN THE WORKPLACE |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| C22.2 NO. 8-13 (R2018) | Electromagnetic interference (EMI) filters |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| CFR 29(PT1910.1000 TO END) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
| IEEE 115-2009 REDLINE | IEEE Guide for Test Procedures for Synchronous Machines Part I—Acceptance and Performance Testing Part II—Test Procedures and Parameter Determination for Dynamic Analysis |
| IEC 60439-1:1999+AMD1:2004 CSV | Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies |
| IEEE 1434-2014 | IEEE Guide for the Measurement of Partial Discharges in AC Electric Machinery |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| ISA S82.02 : 1988 | SAFETY STANDARDS FOR ELECTRICAL AND ELECTRONIC TEST, MEASURING, CONTROLLING AND RELATED EQUIPMENT - ELECTRICAL AND ELECTRONIC TEST AND MEASURING EQUIPMENT |
| NFPA 72 : 2016 | NATIONAL FIRE ALARM AND SIGNALING CODE |
| IEEE 450-2010 REDLINE | IEEE Recommended Practice for Maintenance, Testing, and Replacement of Vented Lead-Acid Batteries for Stationary Applications |
| IEC 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| NEMA ICS 1 : 2000(R2015) | INDUSTRIAL CONTROL AND SYSTEMS: GENERAL REQUIREMENTS |
| API STD 541 : 2014 | FORM-WOUND SQUIRREL CAGE INDUCTION MOTORS - 375 KW (500 HORSEPOWER) AND LARGER |
| IEEE 43-2013 REDLINE | IEEE Recommended Practice for Testing Insulation Resistance of Electric Machinery |
| IEEE 1657A : 2015 | RECOMMENDED PRACTICE FOR PERSONNEL QUALIFICATIONS FOR INSTALLATION AND MAINTENANCE OF STATIONARY BATTERIES - AMENDMENT 1: UPDATED SAFETY SECTIONS |
| IEEE 112-2004 | IEEE Standard Test Procedure for Polyphase Induction Motors and Generators |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| CSA C22.2 No. 6 : 0 | ELECTRIC CLOCKS |
| IEEE 1188A : 2014 | RECOMMENDED PRACTICE FOR MAINTENANCE, TESTING, AND REPLACEMENT OF VALVE-REGULATED LEAD-ACID (VRLA) BATTERIES FOR STATIONARY APPLICATIONS - AMENDMENT 1: UPDATED VRLA MAINTENANCE CONSIDERATIONS |
| IEC 61010-1:2010+AMD1:2016 CSV | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| IEEE 400-2012 REDLINE | IEEE Guide for Field Testing and Evaluation of the Insulation of Shielded Power Cable Systems Rated 5 kV and Above |
| IEC 60068-2-52:2017 | Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) |
| IEEE 45.1-2017 | IEEE Recommended Practice for Electrical Installations on Shipboard--Design |
| IEEE C57.110-2008 REDLINE | IEEE Recommended Practice for Establishing Liquid-Filled and Dry-Type Power and Distribution Transformer Capability When Supplying Nonsinusoidal Load Currents |
| IES RP 12 : 1997 | MARINE LIGHTING |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.