IEEE C57.12.10-2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
TRANSFORMERS - 230 KV AND BELOW 833/958 THROUGH 8333/10 417 KVA, SINGLE-PHASE, AND 750/862 THROUGH 60 000/80 000/100 000 KVA, THREE-PHASE WITHOUT LOAD TAP CHANGING; AND 3750/4687 THROUGH 60 000/80 000/100 000 KVA WITH LOAD TAP CHANGING - SAFETY REQUIREMENT
Hardcopy , PDF
06-01-2011
01-01-2010
1 Introduction and scope
1.1 Introduction
1.2 Scope
1.3 Mandatory requirements
2 Referenced and related standards
2.1 Referenced American National Standards
2.2 Related standard
3 Terminology
4 Rating data
4.1 Usual service conditions
4.2 Kilovolt-ampere ratings
4.3 Kilovolt-ampere and voltage ratings
4.4 Insulation levels
4.5 Taps
4.6 Impedance voltage
4.7 Top-liquid temperature-range limits
4.8 Routine tests
5 Construction
5.1 Accessories
5.2 Bushings
5.3 Lifting, moving, and jacking facilities
5.4 Nameplate
5.5 Ground pads
5.6 Polarity, angular displacement, and terminal markings
5.7 Liquid preservation
5.8 Tanks
5.9 Auxiliary cooling equipment
5.10 Power supply for transformer auxiliary equipment and
controls
6 Basic construction features - load-tap-changing equipment
6.1 Load-tap-changing equipment
6.2 Arcing tap switch
6.3 Motor-drive mechanism
6.4 Position indicator
6.5 Control equipment and accessories
7 Alarm contacts
8 Other ratings
8.1 Other kilovolt-ampere ratings
8.2 Other high-voltage ratings
8.3 Other winding ratings and connections
8.4 Other basic impulse insulation levels (BILs) and
impedance voltages
9 Other construction features - general
9.1 Other bushings
9.2 Other neutral terminations
9.3 Terminal board
9.4 Junction boxes
9.5 Disconnecting switches with interlocks and terminal
chambers
9.6 Throat connections
9.7 Temperature and liquid-level indicator contacts and wiring
9.8 Current transformers
9.9 Provision for future forced-air cooling
9.10 Pressure-type relay
9.11 Moving facilities
9.12 Surge arresters
9.13 Other oil preservation systems
9.14 Other insulating liquid
9.15 Other tanks
9.16 Other loading
9.17 "Other" tests
10 Other construction features - load-tap-changing equipment
10.1 Terminal blocks
10.2 Paralleling circuit and operation
10.3 Omission of automatic load-tap-changing control
10.4 Lightning surge voltage protector for motor power supply
Describes certain electrical, dimensional, and mechanical characteristics and takes into consideration certain safety features of 60-Hz, two-winding, liquid-immersed transformers, and used for step-down or step-up purposes.
| DocumentType |
Standard
|
| Pages |
86
|
| ProductNote |
New child is COR 1 is now added New child COR 2 is now added
|
| PublisherName |
Institute of Electrical & Electronics Engineers
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| IEEE 141 : 1993 | IEEE Recommended Practice for Electric Power Distribution for Industrial Plants |
| TM 5-811-1 : V19950228 | ARMY TECHNICAL MANUAL - ELECTRICAL POWER SUPPLY AND DISTRIBUTION |
| ANSI C57.12.27 : 1982 | LIQUID-FILLED DISTRIBUTION TRANSFORMERS USED IN PAD-MOUNTED INSTALLATIONS INCLUDING UNIT SUBSTATIONS CONFORMANCE STANDARD FOR, |
| ANSI C57.12.13 : 1982 | LIQUID-FILLED TRANSFORMERS USED IN UNIT INSTALLATIONS INCLUDING UNIT SUBSTATIONS, CONFORMANCE STANDARD FOR |
| IEEE 602 : 2007 | ELECTRIC SYSTEMS IN HEALTH CARE FACILITIES |
| IEEE DRAFT C57.18.10 : D12 APR 97 | DRAFT PRACTICES AND REQUIREMENTS FOR SEMICONDUCTOR POWER RECTIFIER TRANSFORMER |
| IEEE DRAFT C57.135 : D12 AUG 2000 | DRAFT GUIDE FOR THE APPLICATION, SPECIFICATION AND TESTING OF PHASE-SHIFTING TRANSFORMERS |
| IEC 62032:2012 | Guide for the Application, Specification and Testing of Phase-Shifting Transformers |
| IEEE C57.92-1981 | IEEE Guide for Loading Mineral-Oil-Immersed Power Transformers Up to and Including 100 MVA with 55 C or 65 C Average Winding Rise |
| IEEE C37.230-2007 | IEEE Guide for Protective Relay Applications to Distribution Lines |
| IEEE DRAFT C57.12.90 : D5.1 98 | DRAFT STANDARD TEST CODE FOR LIQUID-IMMERSED DISTRIBUTION, POWER, AND REGULATING TRANSFORMERS |
| IEEE C57.119-2001 | IEEE Recommended Practice for Performing Temperature Rise Tests on Oil-Immersed Power Transformers at Loads Beyond Nameplate Ratings |
| IEEE C57.12.31-2010 | IEEE Standard for Pole-Mounted Equipment--Enclosure Integrity |
| IEEE C57.135-2011 | IEEE Guide for the Application, Specification, and Testing of Phase-Shifting Transformers |
| IEEE C57.129-2007 REDLINE | IEEE Standard for General Requirements and Test Code for Oil-Immersed HVDC Converter Transformers |
| IEEE C37.121-2012 REDLINE | IEEE Guide for Switchgear - Unit Substation - Requirements |
| IEEE C57.19.01-2000 | IEEE Standard Performance Characteristics and Dimensions for Outdoor Apparatus Bushings |
| IEEE C57.12.00-2015 | IEEE Standard for General Requirements for Liquid-Immersed Distribution, Power, and Regulating Transformers |
| IEEE C57.19.00 : 2004 | GENERAL REQUIREMENTS AND TEST PROCEDURE FOR POWER APPARATUS BUSHINGS |
| IEEE C57.91-2011 REDLINE | IEEE Guide for Loading Mineral-Oil-Immersed Transformers and Step-Voltage Regulators |
| IEEE C57.12.90-2010 | IEEE Standard Test Code for Liquid-Immersed Distribution, Power, and Regulating Transformers |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ANSI C84.1 : 2016 | ELECTRIC POWER SYSTEMS AND EQUIPMENT - VOLTAGE RATINGS (60 HERTZ) |
| IEEE C37.90.1-2012 | IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus |
| IEEE C57.12.70-2011 | IEEE Standard for Standard Terminal Markings and Connections for Distribution and Power Transformers |
| IEEE C57.116-2014 | IEEE Guide for Transformers Directly Connected to Generators |
| IEEE C57.131-2012 | IEEE Standard Requirements for Tap Changers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.