IEEE C57.13.5-2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
IEEE Standard of Performance and Test Requirements for Instrument Transformers of a Nominal System Voltage of 115 kV and Above
04-02-2022
English
30-12-2009
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. Overview
2. Normative references
3. Definitions
4. General
5. Test conditions
6. Classification of test
7. Routine test procedures (applicable to instrument
transformers)
8. Routine test procedures (applicable to current
transformers)
9. Routine test procedures (applicable to voltage
transformers)
10. Type test procedures (applicable to instrument
transformers)
11. Type test procedure (applicable to current
transformers)
12. Special test procedures
13. Identification of test sample in the type test
report
Annex A (normative) - Test code
Annex B (informative) - Dielectric test performed at
an altitude of 1000 m or less for instrument
transformers designed for installation at
altitudes greater than 1000 m
Annex C (informative) - Dielectric tests, oil sampling,
and other related measurements in the field
Annex D (informative) - Internal arc protection for
instrument transformers
Annex E (normative) - Validity of type test reports
and guidance for reviewing the design comparison
report for the modified design
Annex F (informative) - Rated voltage factor
Annex G (normative) - Current transformers used for the
detection of unbalance current of capacitor banks
Annex H (informative) - Current transformers having
transient performance requirements
Annex I (informative) - Electrical endurance test,
explanatory note
Annex J (informative) - Bibliography
Pertains to single-phase instrument transformers of a nominal system voltage of 115 kV and above with capacitive insulation system for line-to-ground connection and for both indoor and outdoor application.
| Committee |
Transformers
|
| DocumentType |
Standard
|
| ISBN |
978-0-7381-6086-3
|
| Pages |
77
|
| PublisherName |
Institute of Electrical & Electronics Engineers
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| CSA C60044-5:2007 | INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS |
| CSA C60044-5 : 2007 : R2011 | INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS |
| IEEE 1601-2010 | IEEE Trial-Use Standard for Optical AC Current and Voltage Sensing Systems |
| CSA C60044-1 : 2007 : R2011 | INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS |
| CSA C60044-1 : 2007 | INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS |
| IEEE 1861-2014 | IEEE Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above |
| IEEE C57.13-2016 | IEEE Standard Requirements for Instrument Transformers |
| IEEE C37.241-2017 | IEEE Guide for Application of Optical Instrument Transformers for Protective Relaying |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| IEEE C57.19.100-2012 REDLINE | IEEE Guide for Application of Power Apparatus Bushings |
| EN 50052:2016 | High-voltage switchgear and controlgear - Gas-filled cast aluminium alloy enclosures |
| IEEE 4-1995 | IEEE Standard Techniques for High-Voltage Testing |
| NEMA 107:2016 | Methods of Measurement of Radio Influence Voltage (RIV) of High Voltage Apparatus |
| IEEE C57.19.01-2000 | IEEE Standard Performance Characteristics and Dimensions for Outdoor Apparatus Bushings |
| EN 50064 : 1989 COR 2007 | WROUGHT ALUMINIUM AND ALUMINIUM ALLOY ENCLOSURES FOR GAS-FILLED HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR |
| ASTM D 1275 : 2015 | Standard Test Method for Corrosive Sulfur in Electrical Insulating Liquids |
| IEEE 4-2013 | IEEE Standard for High-Voltage Testing Techniques |
| IEEE C62.11-2005 | IEEE Standard for Metal-Oxide Surge Arresters for AC Power Circuits (> 1 kV) |
| IEC 60044-6:1992 | Instrument transformers - Part 6: Requirements for protective current transformers for transient performance |
| ASTM D 1868 : 2013 : REDLINE | Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems |
| IEC 61181:2007+AMD1:2012 CSV | Mineral oil-filled electrical equipment - Application of dissolved gas analysis (DGA) to factory tests on electrical equipment |
| EN 50068 : 1991 COR 2007 | WROUGHT STEEL ENCLOSURES FOR GAS FILLED HIGH VOLTAGE SWITCHGEAR AND CONTROLGEAR |
| IEEE C57.13-2008 | IEEE Standard Requirements for Instrument Transformers |
| IEEE 693-2005 | IEEE Recommended Practice for Seismic Design of Substations |
| IEEE C57.106-2006 | IEEE Guide for Acceptance and Maintenance of Insulating Oil in Equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.