IEEE/IEC C37.60-2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
IEEE/IEC International Standard - High-voltage switchgear and controlgear - Part 111: Automatic circuit reclosers and fault interrupters for alternating current systems up to 38 kV
12-02-2019
English
18-09-2012
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
1 Overview
2 Normal and special service conditions
3 Terms and definitions
4 Ratings
5 Design and construction
6 Type tests
7 Routine tests
8 Guide to the selection of switchgear and controlgear
9 Information to be given with enquiries, tenders and orders
10 Transport, storage, installation, operation and maintenance
11 Safety
12 Influence of the product on the environment
101 Additional application and test information
Annex A (informative) - X/R Ratios
Annex B (informative) - Simulated surge arrester operation test
Annex C (normative) - Method of drawing the envelope of the
prospective transient recovery voltage of a circuit
and determining the representative parameters
Annex D (informative) - Background basis of recloser TRV values
Annex E (normative) - Tolerances for test values
Annex F (informative) - Definition for the automatic circuit
recloser
Annex G (informative) - Definition for the fault interrupter
Annex H (informative) - Basis of derivation of duty factors
and standard operating duties
Annex I (normative) - Ratings for oil interrupting reclosers and
hydraulically controlled reclosers
Annex J (normative) - Standard methods for determining the
values of a sinusoidal current wave and a power-frequency
recovery voltage
Annex K (normative) - Altitude correction factors
Annex L (informative) - Comparison of definitions related to the
unit operation
Annex M (informative) - Corrosion protection
Bibliography
Pertains toall overhead, pad mounted, dry vault and submersible single or multi-pole alternating current automatic circuit reclosers and fault interrupters for rated maximum voltages above 1000 V and up to 38 kV.
| Committee |
Switchgear
|
| DevelopmentNote |
Also numbered as IEC 62271-111. (11/2005) Supersedes IEEE DRAFT C37.60. (09/2003) To be read in conjunction with IEC 62271-1:2007. (09/2012)
|
| DocumentType |
Standard
|
| ISBN |
978-0-7381-7309-2
|
| Pages |
134
|
| PublisherName |
Institute of Electrical & Electronics Engineers
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| IEEE 386-2016 | IEEE Standard for Separable Insulated Connector Systems for Power Distribution Systems Rated 2.5 kV through 35 kV |
| IEEE 1584-2002 | IEEE Guide for Performing Arc Flash Hazard Calculations |
| ESI 41-27 : ISSUE 1 AMD 2 | OUTDOOR DISTRIBUTION SWITCHGEAR FOR SERVICE UP TO 36kV (OVERHEAD CONDUCTOR CONNECTED) |
| IEEE C37.100.1-2007 | IEEE Standard of Common Requirements for High Voltage Power Switchgear Rated Above 1000 V |
| IEEE C37.302-2015 | IEEE Guide for Fault Current Limiter (FCL) Testing of FCLs Rated above 1000 V AC |
| IEEE C37.63-2013 REDLINE | IEEE Standard Requirements for Overhead, Pad-Mounted, Dry-Vault, and Submersible Automatic Line Sectionalizers for Alternating Current Systems Up to 38 kV |
| IEEE DRAFT C37.108 : D6 98 | DRAFT GUIDE FOR THE PROTECTION OF NETWORK TRANSFORMERS |
| UFC 3-550-01 : CHANGE 1 | UNIFIED FACILITIES CRITERIA - EXTERIOR ELECTRICAL POWER DISTRIBUTION |
| IEEE C37.016-2006 | IEEE Standard for AC High Voltage Circuit Switchers rated 15.5kV through 245kV |
| IEEE C37.74-2014 | IEEE Standard Requirements for Subsurface, Vault, and Padmounted Load-Interrupter Switchgear and Fused Load-Interrupter Switchgear for Alternating Current Systems up to 38 kV |
| IEEE C57.12.32-2002 | IEEE Standard for Submersible Equipment - Enclosure Integrity |
| IEEE C37.104-2012 REDLINE | IEEE Guide for Automatic Reclosing of Circuit Breakers for AC Distribution and Transmission Lines |
| ENA TS 41-27 : ISSUE 1 AMD 3 | OUTDOOR DISTRIBUTION SWITCHGEAR FOR SERVICE UP TO 36 KV (OVERHEAD CONDUCTOR CONNECTED) |
| IEEE C37.62-2020 | IEEE Standard for Pad-Mounted Dry Vault, Submersible, and Overhead Fault Interrupters for Alternating Current Systems Up to and Including 38 kV |
| IEEE C37.90.1-2002 | IEEE Standard Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus |
| IEC 62271-100:2008+AMD1:2012+AMD2:2017 CSV | High-voltage switchgear and controlgear - Part 100: Alternating-current circuit-breakers |
| IEC 60255-22-1:2007 | Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity tests |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| IEEE C37.90-2005 | IEEE Standard for Relays and Relay Systems Associated with Electric Power Apparatus |
| IEC 62271-200:2011 | High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
| IEEE 1-2000 | IEEE Recommended Practice - General Principles for Temperature Limits in the Rating of Electrical Equipment and for the Evaluation of Electrical Insulation |
| IEC 62271-207:2012 | High-voltage switchgear and controlgear - Part 207: Seismic qualification for gas-insulated switchgear assemblies for rated voltages above 52 kV |
| IEEE C37.100.1-2007 | IEEE Standard of Common Requirements for High Voltage Power Switchgear Rated Above 1000 V |
| IEC 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
| IEEE 4-1995 | IEEE Standard Techniques for High-Voltage Testing |
| IEEE 386-2016 | IEEE Standard for Separable Insulated Connector Systems for Power Distribution Systems Rated 2.5 kV through 35 kV |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| IEC TR 62271-300:2006 | High-voltage switchgear and controlgear - Part 300: Seismic qualification of alternating current circuit-breakers |
| CSA C22.2 No. 31 : 2014 | SWITCHGEAR ASSEMBLIES |
| IEEE 400.2-2013 REDLINE | IEEE Guide for Field Testing of Shielded Power Cable Systems Using Very Low Frequency (VLF)(less than 1 Hz) |
| IEEE C37.04B : 2008 | RATING STRUCTURE FOR AC HIGH-VOLTAGE CIRCUIT BREAKERS RATED ON A SYMMETRICAL CURRENT BASIS - AMENDMENT 2: TO CHANGE THE DESCRIPTION OF TRANSIENT RECOVERY VOLTAGE FOR HARMONIZATION WITH IEC 62271-100 |
| IEC TS 62271-304:2008 | High-voltage switchgear and controlgear - Part 304: Design classes for indoor enclosed switchgear and controlgear for rated voltages above 1 kV up to and includuing 52 kV to be used in severe climatic conditions |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEEE 4-2013 | IEEE Standard for High-Voltage Testing Techniques |
| IEC 60721-2-2:2012 | Classification of environmental conditions - Part 2-2: Environmental conditions appearing in nature - Precipitation and wind |
| IEEE C57.12.28-2005 | IEEE Standard for Pad-Mounted Equipment - Enclosure Integrity |
| IEEE C37.90.3-2001 | IEEE Standard Electrostatic Discharge Tests for Protective Relays |
| ANSI C37.85 : 1989 | ALTERNATING-CURRENT HIGH-VOLTAGE POWER VACUUM INTERRUPTERS - SAFETY REQUIREMENTS FOR X-RADIATION LIMITS |
| IEEE C2-2017 | NATIONAL ELECTRICAL SAFETY CODE (NESC)(R) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEEE C57.12.29-2014 | IEEE Standard for Pad-Mounted Equipment--Enclosure Integrity for Coastal Environments |
| IEC 60255-22-6:2001 | Electrical relays - Part 22-6: Electrical disturbance tests for measuring relays and protection equipment - Immunity to conducted disturbances induced by radio frequency fields |
| IEEE C37.40-2003 | IEEE Standard Service Conditions and Definitions for High-Voltage Fuses, Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories |
| IEC 60255-22-3:2007 | Measuring relays and protection equipment - Part 22-3: Electrical disturbance tests - Radiated electromagnetic field immunity |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| IEC TR 60943:1998+AMD1:2008 CSV | Guidance concerning the permissible temperature rise for parts of electrical equipment, in particular for terminals |
| IEEE C37.90.2:2004 | WITHSTAND CAPABILITY OF RELAY SYSTEMS TO RADIATED ELECTROMAGNETIC INTERFERENCE FROM TRANSCEIVERS |
| IEC 62208:2011 | Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements |
| IEEE C37.90.1-2012 | IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus |
| IEC 60255-22-2:2008 | Measuring relays and protection equipment - Part 22-2: Electrical disturbance tests - Electrostatic discharge tests |
| IEEE C37.301-2009 | IEEE Standard for High-Voltage Switchgear (Above 1000 V) Test Techniques--Partial Discharge Measurements |
| IEC 60255-151:2009 | Measuring relays and protection equipment - Part 151: Functional requirements for over/under current protection |
| IEEE C37.20.7-2007 REDLINE | IEEE Guide for Testing Metal-Enclosed Switchgear Rated Up to 38 kV for Internal Arcing Faults |
| IEC 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEEE C57.12.31-2010 | IEEE Standard for Pole-Mounted Equipment--Enclosure Integrity |
| IEEE C37.24-2003 | IEEE Guide for Evaluating the Effect of Solar Radiation on Outdoor Metal-Enclosed Switchgear |
| IEC 60071-2:1996 | Insulation co-ordination - Part 2: Application guide |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| IEC 60059:1999+AMD1:2009 CSV | IEC standard current ratings |
| IEEE C37.41-2008 REDLINE | IEEE Standard Design Tests for High-Voltage (>1000 V) Fuses, Fuse and Disconnecting Cutouts, Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Fuse Links and Accessories Used with These Devices |
| IEC 60507:2013 | Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems |
| IEC 60050-448:1995 | International Electrotechnical Vocabulary (IEV) - Part 448: Power system protection |
| IEEE C57.12.28-2014 | IEEE Standard for Pad-Mounted Equipment--Enclosure Integrity |
| IEC 62271-2:2003 | High-voltage switchgear and controlgear - Part 2: Seismic qualification for rated voltages of 72,5 kV and above |
| IEEE C37.06-2009 | IEEE Standard for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis--Preferred Ratings and Related Required Capabilities for Voltages Above 1000 V |
| IEEE 693-2005 | IEEE Recommended Practice for Seismic Design of Substations |
| IEC 60282-2:2008 | High-voltage fuses - Part 2: Expulsion fuses |
| IEC 62271-102:2001+AMD1:2011+AMD2:2013 CSV | High-voltage switchgear and controlgear - Part 102: Alternatingcurrent disconnectors and earthing switches |
| IEEE C37.100-1992 | IEEE Standard Definitions for Power Switchgear |
| IEC 60255-22-4:2008 | Measuring relays and protection equipment - Part 22-4: Electrical disturbance tests - Electrical fast transient/burst immunity test |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.