UNI EN 13463-5 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
NON-ELECTRICAL EQUIPMENT INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 5: PROTECTION BY CONSTRUCTIONAL SAFETY 'C'
12-05-2016
01-01-2011
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Requirements for moving parts
6 Requirements for bearings
7 Requirements for power transmission systems
8 Requirements for brakes and braking systems
9 Requirements for springs and absorbing elements
10 Requirements for conveyor belts
11 Marking
Annex A (informative) - Examples for an ignition
hazard assessment report for typical equipment parts
and potential ignition sources
Annex B (normative) - Test requirements
Annex C (informative) - Significant technical changes
between this European Standard and EN 13463-5:2003
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 94/9/EC
Bibliography
Describes the requirements for the design and construction of non-electrical equipment, intended for use in potentially explosive atmospheres, protected by the type of protection Constructional Safety 'c'.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| SN EN 13463-5 : 2011 | Identical |
| BS EN 13463-5:2011 | Identical |
| UNE-EN 13463-5:2013 | Identical |
| NEN EN 13463-5 : 2011 | Identical |
| DIN EN 13463-5:2011-10 | Identical |
| I.S. EN 13463-5:2011 | Identical |
| EN 13463-5:2011 | Identical |
| NF EN 13463-5 : 2011 | Identical |
| NS EN 13463-5 : 2011 | Identical |
| NBN EN 13463-5 : 2011 | Identical |
| DIN EN 13463-5:2004-03 | Identical |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| ISO 9563:2015 | Belt drives Electrical conductivity of antistatic endless synchronous belts Characteristics and test method |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 14973:2015 | Conveyor belts for use in underground installations - Electrical and flammability safety requirements |
| EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
| EN 13478:2001+A1:2008 | Safety of machinery - Fire prevention and protection |
| EN ISO 340:2013 | Conveyor belts - Laboratory scale flammability characteristics - Requirements and test method (ISO 340:2013) |
| EN 13237:2012 | Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres |
| EN 13463-6:2005 | Non-electrical equipment for use in potentially explosive atmospheres - Part 6: Protection by control of ignition source 'b' |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| ISO 340:2013 | Conveyor belts Laboratory scale flammability characteristics Requirements and test method |
| EN 14986:2017 | Design of fans working in potentially explosive atmospheres |
| EN ISO 284:2012 | Conveyor belts - Electrical conductivity - Specification and test method (ISO 284:2012) |
| EN 13463-8:2003 | Non-electrical equipment for potentially explosive atmospheres - Part 8: Protection by liquid immersion 'k' |
| ISO 1813:2014 | Belt drives — V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts — Electrical conductivity of antistatic belts: Characteristics and methods of test |
| EN 1127-2:2014 | Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 1554:2012 | Conveyor belts - Drum friction testing |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN 50303:2000 | Group I, Category M1 equipment intended to remain functional in atmospheres endangered by firedamp and/or coal dust |
| CLC/TR 50404:2003 | Electrostatics - Code of practice for the avoidance of hazards due to static electricity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.