UNI EN 15827 : 2011
Current
Current
The latest, up-to-date edition.
RAILWAY APPLICATIONS - REQUIREMENTS FOR BOGIES AND RUNNING GEARS
Published date
12-05-2011
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Technical specification and interface management
5 Engineering process
6 Structural design criteria
7 Dynamic performance criteria
8 Acceptance criteria
9 Validation of the design
10 Quality requirements
11 Maintenance plan
12 Proven operating envelope
Annex A (informative) - Technical Specification
Annex B (informative) - Engineering process requirements
Annex C (informative) - Design loads
Annex D (normative) - Component related standards
Annex E (informative) - Design development and simulation
Annex F (informative)- Acceptance process flow diagram
Annex G (informative) - Dynamic performance validation by
numerical simulation
Annex H (normative) - Minimum requirements for maintenance
inspections
Annex I (informative) - Proven operating envelope
Annex J (normative) - Standardised bogies/running gear for
freight wagons
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2008/57/EC
Bibliography
This standard consolidates all the separate requirements specified in rolling stock TSIs d European standards relating to bogies and running gear together into an overall requirement and process that ensures a functional and safe design is achieved for a defined operating envelope.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Current
|
| Standards | Relationship |
| EN 15827:2011 | Identical |
| EN 15687:2010 | Railway applications - Testing for the acceptance of running characteristics of freight vehicles with static axle loads higher than 225 kN and up to 250 kN |
| EN 15437-1:2009 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 1: Track side equipment and rolling stock axlebox |
| EN 14200:2004 | Railway applications - Suspension components - Parabolic springs, steel |
| PREN 15437-2 : DRAFT 2010 | RAILWAY APPLICATIONS - AXLEBOX CONDITION MONITORING - PERFORMANCE REQUIREMENTS - PART 2: ONBOARD SYSTEMS FOR TEMPERATURE MONITORING |
| EN 15313:2016 | Railway applications - In-service wheelset operation requirements - In-service and off-vehicle wheelset maintenance |
| UIC 432 : 12ED 2008 | WAGONS - RUNNING SPEEDS - TECHNICAL CONDITIONS TO BE OBSERVED |
| EN 1032:2003+A1:2008 | Mechanical vibration - Testing of mobile machinery in order to determine the vibration emission value |
| EN 14363:2016 | Railway applications - Testing and Simulation for the acceptance of running characteristics of railway vehicles - Running Behaviour and stationary tests |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 15085-1:2007+A1:2013 | Railway applications - Welding of railway vehicles and components - Part 1: General |
| PREN 15839 : DRAFT 2012 | RAILWAY APPLICATIONS - TESTING FOR THE ACCEPTANCE OF RUNNING CHARACTERISTICS OF RAILWAY VEHICLES - FREIGHT WAGONS - TESTING OF RUNNING SAFETY UNDER LONGITUDINAL COMPRESSIVE FORCES |
| DIN 25201-1:2015-12 | DESIGN GUIDE FOR RAILWAY VEHICLES AND THEIR COMPONENTS - BOLTED JOINTS - PART 1: CLASSIFICATION OF BOLTED JOINTS |
| EN 13715:2006+A1:2010 | Railway applications - Wheelsets and bogies - Wheels - Tread profile |
| DIN 25201-2:2015-12 | DESIGN GUIDE FOR RAILWAY VEHICLES AND THEIR COMPONENTS - BOLTED JOINTS - PART 2: DESIGN - MECHANICAL APPLICATIONS |
| EN 14817:2006 | Railway applications - Suspension components - Air spring control elements |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN 60721-3-5:1997 | Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 5: Ground vehicle installations |
| IEC 60721-3-5:1997 | Classification of environmental conditions - Part 3: Classificationof groups of environmental parameters and their severities -Section 5: Ground vehicle installations |
| CEN/TS 45545-2:2009 | Railway applications - Fire protection on railway vehicles - Part 2: Requirements for fire behaviour of materials and components |
| DIN 7190:2001-02 | INTERFERENCE FITS - CALCULATION AND DESIGN RULES |
| EN 13848-1:2003+A1:2008 | Railway applications - Track - Track geometry quality - Part 1: Characterisation of track geometry |
| EN 15049:2007 | Railway applications - Suspension components - Torsion bar, steel |
| EN 12299:2009 | Railway applications - Ride comfort for passengers - Measurement and evaluation |
| EN 12080:2017 | Railway applications - Axleboxes - Rolling bearings |
| EN 12081:2017 | Railway applications - Axleboxes - Lubricating greases |
| EN 15085-5:2007 | Railway applications - Welding of railway vehicles and components - Part 5: Inspection, testing and documentation |
| NFF 32 101 : 1978 | RAILWAY TRANSPORT EQUIPMENT - TWO AXLE CARRYING BOGIE FRAMES - DETERMINATION OF REFERENCE ELEMENTS - GEOMETRICAL CHECKS |
| EN ISO 3095:2013 | Acoustics - Railway applications - Measurement of noise emitted by railbound vehicles (ISO 3095:2013) |
| PREN 15892 : DRAFT 2009 | RAILWAY APPLICATIONS - NOISE EMISSION - MEASUREMENT OF NOISE INSIDE DRIVER'S CABS |
| EN 14535-1:2005+A1:2011 | Railway applications - Brake discs for railway rolling stock - Part 1: Brake discs pressed or shrunk onto the axle or drive shaft, dimensions and quality requirements |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 12082:2017 | Railway applications - Axleboxes - Performance testing |
| NFE 22 622 : 1988 | MECHANICAL TRANSMISSIONS - PRESSED-ON ASSEMBLIES ON CONICAL BEARINGS - FUNCTION, REALIZATION, CALCULATION |
| EN 15273-2:2013+A1:2016 | Railway applications - Gauges - Part 2: Rolling stock gauge |
| NFE 25 030-1 : 2014 | FASTENERS - THREADED CONNECTIONS WITH ISO METRIC THREAD - PART 1: DESIGN RULES FOR TENSILE LOADED BOLTED JOINTS - SIMPLIFIED PROCEDURE - FIXATIONS |
| EN 13803-2:2006+A1:2009 | Railway applications - Track - Track alignment design parameters - Track gauges 1 435 mm and wider - Part 2: Switches and crossings and comparable alignment design situations with abrupt changes of curvature |
| EN 15227:2008+A1:2010 | Railway applications - Crashworthiness requirements for railway vehicle bodies |
| EN 50125-1:2014 | Railway applications - Environmental conditions for equipment - Part 1: Rolling stock and on-board equipment |
| EN 13913:2003 | Railway applications - Rubber suspension components - Elastomer-based mechanical parts |
| EN 13104:2009+A2:2012 | Railway applications - Wheelsets and bogies - Powered axles - Design method |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 13261:2009+A1:2010 | Railway applications - Wheelsets and bogies - Axles - Product requirements |
| EN 13597:2003 | Railway applications - Rubber suspension components - Rubber diaphragms for pneumatic suspension springs |
| EN 15528:2015 | Railway applications - Line categories for managing the interface between load limits of vehicles and infrastructure |
| EN 15302:2008+A1:2010 | Railway applications - Method for determining the equivalent conicity |
| EN 13803-1:2010 | Railway applications - Track - Track alignment design parameters - Track gauges 1435 mm and wider - Part 1: Plain line |
| PREN 14535-2 : DRAFT 2016 | RAILWAY APPLICATIONS - BRAKE DISCS FOR RAILWAY ROLLING STOCK - PART 2: BRAKE DISCS MOUNTED ONTO THE WHEEL, DIMENSIONS AND QUALITY REQUIREMENTS |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 13298:2003 | Railway applications - Suspension components - Helical suspension springs, steel |
| NFE 90 401-2 : 2001 | MECHANICAL VIBRATION AND SHOCK - EVALUATION OF HUMAN EXPOSURE TO WHOLE-BODY VIBRATION - PART 2: GENERAL REQUIREMENTS |
| EN 13262:2004+A2:2011 | Railway applications - Wheelsets and bogies - Wheels - Product requirements |
| ISO 2631-1:1997 | Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements |
| EN 13802:2013 | Railway applications - Suspension components - Hydraulic dampers |
| EN 15663:2017 | Railway applications - Vehicle reference masses |
| EN 13260:2009+A1:2010 | Railway applications - Wheelsets and bogies - Wheelsets - Product requirements |
| ISO 3095:2013 | Acoustics Railway applications Measurement of noise emitted by railbound vehicles |
| UIC 518 : 4ED 2009 | TESTING AND APPROVAL OF RAILWAY VEHICLES FROM THE POINT OF VIEW OF THEIR DYNAMIC BEHAVIOUR - SAFETY - TRACK FATIGUE - RIDE QUALITY |
| NFE 22 620 : 1980 | PRESSED-ON ASSEMBLIES - DIMENSIONS, TOLERANCES AND SURFACE CONDITION OF USUAL ASSEMBLIES |
| EN 12663-1:2010+A1:2014 | Railway applications - Structural requirements of railway vehicle bodies - Part 1: Locomotives and passenger rolling stock (and alternative method for freight wagons) |
| EN 15085-2:2007 | Railway applications - Welding of railway vehicles and components - Part 2: Quality requirements and certification of welding manufacturer |
| NFE 22 621 : 2015 | MECHANICAL TRANSMISSIONS - PRESSED-ON ASSEMBLIES ON CYLINDRICAL SHAFT - FUNCTION, REALISATION, CALCULATION |
| EN 13103:2009+A2:2012 | Railway applications - Wheelsets and bogies - Non powered axles - Design method |
| EN 13979-1:2003+A2:2011 | Railway applications - Wheelsets and bogies - Monobloc wheels - Technical approval procedure - Part 1: Forged and rolled wheels |
| EN 12663-2:2010 | Railway applications - Structural requirements of railway vehicle bodies - Part 2: Freight wagons |
| EN 13749:2011 | Railway applications - Wheelsets and bogies - Method of specifying the structural requirements of bogie frames |
| EN 15686:2010 | Railway applications - Testing for the acceptance of running characteristics of railway vehicles with cant deficiency compensation system and/or vehicles intended to operate with higher cant deficiency than stated in EN 14363:2005, Annex G |
| EN 15085-4:2007 | Railway applications - Welding of railway vehicles and components - Part 4: Production requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.