UNI EN ISO 16911-1 : 2013
Current
The latest, up-to-date edition.
STATIONARY SOURCE EMISSIONS - MANUAL AND AUTOMATIC DETERMINATION OF VELOCITY AND VOLUME FLOW RATE IN DUCTS - PART 1: MANUAL REFERENCE METHOD
16-05-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principle
6 Selection of monitoring approach
7 Measuring equipment
8 Performance characteristics and requirements
9 Measurement procedure
10 Calculation of results
11 Establishment of the uncertainty of results
12 Evaluation of the method
Annex A (normative) - Measurement of velocity
using differential pressure based techniques
Annex B (normative) - Vane anemometer
Annex C (normative) - Tracer gas dilution method
determination of volume flow rate and
average velocity
Annex D (normative) - Transit time tracer gas
method determination of average velocity
Annex E (normative) - Calculation of flue gas
volume flow rate from energy consumption
Annex F (informative) - Example of uncertainty
budget established for velocity and volume
flow rate measurements by Pitot tube
Annex G (informative) - Description of validation
studies
Annex H (informative) - Differential pressure
measurement
Annex I (informative) - The use of time of flight
measurement instruments based on modulated
laser light
Annex J (informative) - Relationship between this
International Standard and the essential
requirements of EU Directives
Bibliography
Defines a method for periodic determination of the axial velocity and volume flow rate of gas within emissions ducts and stacks.
| Committee |
CT 4
|
| DevelopmentNote |
Together with UNI EN ISO 16911-2, supersedes UNI 10169. (05/2013)
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| ISO 16911-1:2013 | Identical |
| EN ISO 16911-1:2013 | Identical |
| EN 15267-3:2007 | Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources |
| BS 5857-1.4:1980 | Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of water flow Transit time method using non-radioactive tracers |
| BS 5857-2.4:1980 | Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of gas flow Transit time method using radioactive tracers |
| ISO 1928:2009 | Solid mineral fuels Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value |
| CEN/TS 14793:2005 | Stationary source emission - Intralaboratory validation procedure for an alternative method compared to a reference method |
| ISO 14956:2002 | Air quality — Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty |
| ISO 1170:2013 | Coal and coke Calculation of analyses to different bases |
| ECA 4-02 : 2013 | EVALUATION OF THE UNCERTAINTY OF MEASUREMENT IN CALIBRATION |
| EN 14789:2017 | Stationary source emissions - Determination of volume concentration of oxygen - Standard reference method: Paramagnetism |
| EN 15259:2007 | Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report |
| EN 13284-1:2017 | Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method |
| EN 14181:2014 | Stationary source emissions - Quality assurance of automated measuring systems |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN 12952-15:2003 | Water-tube boilers and auxiliary installations - Part 15: Acceptance tests |
| EN 14790:2017 | Stationary source emissions - Determination of the water vapour in ducts - Standard reference method |
| ISO 20988:2007 | Air quality Guidelines for estimating measurement uncertainty |
| ISO 10780:1994 | Stationary source emissions — Measurement of velocity and volume flowrate of gas streams in ducts |
| ISO 3966:2008 | Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.