16/30338117 DC : 0
NA
Status of Standard is Unknown
BS EN 13493 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
Hardcopy , PDF
English
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Required characteristics and corresponding
methods of test
5 Assessment and verification of constancy
of performance (AVCP)
Annex A (normative) - Durability of geosynthetic barriers
Annex ZA (informative) - Relationship of this European
Standard with Regulation (EU) No. 305/2011
Bibliography
BS EN 13493.
Committee |
B/553
|
DocumentType |
Draft
|
Pages |
52
|
PublisherName |
British Standards Institution
|
Status |
NA
|
Standards | Relationship |
PREN 13493 : DRAFT 2016 | Identical |
EN 13265:2016 | Geotextiles and geotextile-related products - Characteristics required for use in liquid waste containment projects |
EN 14576:2005 | Geosynthetics - Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking |
EN ISO 11358-1:2014 | Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2014) |
EN 14575:2005 | Geosynthetic barriers - Screening test method for determining the resistance to oxidation |
EN 12226:2012 | Geosynthetics - General tests for evaluation following durability testing |
EN ISO 1183-3:1999 | Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method (ISO 1183-3:1999) |
EN 14150:2006 | Geosynthetic barriers - Determination of permeability to liquids |
ISO 13438:2004 | Geotextiles and geotextile-related products Screening test method for determining the resistance to oxidation |
EN ISO 10319:2015 | Geosynthetics - Wide-width tensile test (ISO 10319:2015) |
ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
CEN/TS 14418:2014 | Geosynthetic Barriers - Test method for the determination of the influence of freezing-thawing cycles on the permeability of clay geosynthetic barriers |
EN 13251:2016 | Geotextiles and geotextile-related products - Characteristics required for use in earthworks, foundations and retaining structures |
EN ISO 13426-2:2005 | Geotextiles and geotextile-related products - Strength of internal structural junctions - Part 2: Geocomposites (ISO 13426-2:2005) |
EN 13249:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of roads and other trafficked areas (excluding railways and asphalt inclusion) |
ISO 12236:2006 | Geosynthetics — Static puncture test (CBR test) |
EN 1849-2:2009 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 2: Plastic and rubber sheets |
EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
EN 495-5:2013 | Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: Plastic and rubber sheets for roof waterproofing |
ISO 9863-1:2016 | Geosynthetics Determination of thickness at specified pressures Part 1: Single layers |
EN ISO 13426-1:2003 | Geotextiles and geotextile-related products - Strength of internal structural junctions - Part 1: Geocells (ISO 13426-1:2003) |
ISO 6427:2013 | Plastics — Determination of matter extractable by organic solvents (conventional methods) |
EN 14151:2010 | Geosynthetics - Determination of burst strength |
EN 13253:2016 | Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments) |
ISO 10319:2015 | Geosynthetics — Wide-width tensile test |
EN ISO 6427:2014 | Plastics - Determination of matter extractable by organic solvents (conventional methods) (ISO 6427:2013) |
EN 764-1:2015+A1:2016 | Pressure equipment - Part 1: Vocabulary |
EN 13250:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of railways |
EN 12224:2000 | Geotextiles and geotextile-related products - Determination of the resistance to weathering |
EN ISO 10773:2011 | Clay geosynthetic barriers - Determination of permeability to gases (ISO 10773:2011) |
EN ISO 1133-2:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
ISO 34-1:2015 | Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces |
EN 12311-2:2013 | Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing |
EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
ISO 13426-2:2005 | Geotextiles and geotextile-related products — Strength of internal structural junctions — Part 2: Geocomposites |
EN 13255:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of canals |
EN 13254:2016 | Geotextiles and geotextile-related products - Characteristics required for the use in the construction of reservoirs and dams |
EN 12311-1:1999 | Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of tensile properties |
ISO/TS 13434:2008 | Geosynthetics Guidelines for the assessment of durability |
EN 1844:2013 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
EN 12310-1:1999 | Flexible sheets for waterproofing - Part 1: Bitumen sheets for waterproofing - Determination of resistance to tearing (nail shank) |
EN ISO 16993:2016 | Solid biofuels - Conversion of analytical results from one basis to another (ISO 16993:2016) |
EN 14414:2004 | Geosynthetics - Screening test method for determining chemical resistance for landfill applications |
ISO 12957-1:2005 | Geosynthetics Determination of friction characteristics Part 1: Direct shear test |
ASTM D 1603 : 2014 : REDLINE | Standard Test Method for Carbon Black Content in Olefin Plastics |
EN 16416:2013 | Geosynthetic clay barriers - Determination of water flux index - Flexible wall permeameter method at constant head |
EN 1109:2013 | Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of flexibility at low temperature |
CEN/TS 14417:2014 | Geosynthetic barriers - Test method for the determination of the influence of wetting-drying cycles on the permeability of clay geosynthetic barriers |
EN ISO 10318-1:2015 | Geosynthetics - Part 1: Terms and definitions (ISO 10318-1:2015) |
EN ISO 1133-1:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
ASTM D 696 : 2016 : REDLINE | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
EN ISO 12957-2:2005 | Geosynthetics - Determination of friction characteristics - Part 2: Inclined plane test (ISO 12957-2:2005) |
EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
EN ISO 16994:2016 | Solid biofuels - Determination of total content of sulfur and chlorine (ISO 16994:2016) |
ISO 13426-1:2003 | Geotextiles and geotextile-related products Strength of internal structural junctions Part 1: Geocells |
ISO 12957-2:2005 | Geosynthetics — Determination of friction characteristics — Part 2: Inclined plane test |
ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
ISO 11358-1:2014 | Plastics Thermogravimetry (TG) of polymers Part 1: General principles |
EN 12225:2000 | Geotextiles and geotextile-related products - Method for determining the microbiological resistance by a soil burial test |
EN 14196:2016 | Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers |
EN 1296:2000 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roofing - Method of artificial ageing by long term exposure to elevated temperature |
ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
EN ISO 9864:2005 | Geosynthetics - Test method for the determination of mass per unit area of geotextiles and geotextile-related products (ISO 9864:2005) |
EN ISO 9863-1:2016 | Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers (ISO 9863-1:2016) |
ISO 9001:2015 | Quality management systems — Requirements |
ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
ISO 10390:2005 | Soil quality Determination of pH |
ISO 3696:1987 | Water for analytical laboratory use — Specification and test methods |
ISO 10773:2011 | Clay geosynthetic barriers Determination of permeability to gases |
EN 13256:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of tunnels and underground structures |
EN ISO 3696:1995 | Water for analytical laboratory use - Specification and test methods (ISO 3696:1987) |
EN 1849-1:1999 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 1: Bitumen sheets for roof waterproofing |
ISO 1133-2:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture |
EN ISO 12236:2006 | Geosynthetics - Static puncture test (CBR test) (ISO 12236:2006) |
EN 13257:2016 | Geotextiles and geotextile-related products - Characteristics required for use in solid waste disposals |
ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
EN 13252:2016 | Geotextiles and geotextile-related products - Characteristics required for use in drainage systems |
ISO 9864:2005 | Geosynthetics — Test method for the determination of mass per unit area of geotextiles and geotextile-related products |
EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
CEN/TS 14416:2014 | Geosynthetic barriers - Test method for determining the resistance to roots |
EN 14415:2004 | Geosynthetic barriers - Test method for determining the resistance to leaching |
ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
EN ISO 1183-2:2004 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.