BS 2011-2.1N:1985
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Environmental testing. Tests Test N. Change of temperature
Hardcopy , PDF
15-04-2000
English
28-02-1985
National foreword
Method
Introduction
1 Test Na: Rapid change of temperature with
prescribed time of transition
2 Test Nb: Change of temperature with specified rate
of change
3 Test Nc: Rapid change of temperature, two-fluid-bath
method
Figures
1 Untitled
2 Untitled
3 Untitled
Gives three methods of test for the determination of the effect on a specimen of a change of temperature or a succession of changes of temperature. Tests Na and Nc are with a rapid change of temperature; Test Nb is with a specified rate of change.
Committee |
GEL/104
|
DevelopmentNote |
Implements CENELEC HD 323.2.14 S2
|
DocumentType |
Standard
|
Pages |
14
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
IEC 60068-2-14:2009 | Identical |
BS QC 222000:1996 | Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with screw coupling. Characteristic impedance 50 ohms. (Type TNC) |
BS 5760-13.3:1993 | Reliability of systems, equipment and components. Guide to reliability test conditions for consumer equipment Conditions providing a low degree of simulation for equipment for stationary use in partially weatherprotected locations |
BS EN 61049:1993 | Specification for capacitors for use in tubular fluorescent and other discharge lamp circuits. Performance requirements |
BS 6796:1986 | Specification for flickermeters |
BS 5917:1980 | Specification for conformal coating material for use on printed circuit assemblies |
BS EN 119000:1997 | Harmonized system of quality assessment for electronic components. Generic specification: dry and mercury wetted reed contact units |
BS 5760-13.5:1996 | Reliability of systems, equipment and components. Guide to reliability test conditions for consumer equipment Ground mobile equipment. Low degree of simulation |
DEFSTAN 22-48/2(2001) : 2001 | SPECIFICATION FOR POSITIVE TEMPERATURE COEFFICIENT THERMISTORS FOR THERMAL PROTECTION OF ELECTRIC MOTORS |
BS CECC 20000:1983 | Harmonized system of quality assessment for electronic components: generic specification: semiconductor optoelectronic and liquid crystal devices |
BS QC 410000:1990 | Harmonized system of quality assessment for electronic components: potentiometers for use in electronic equipment |
BS EN 169000:1993 | Harmonized system of quality assessment for electronic components. Generic specification. Quartz crystal controlled oscillators |
BS EN 129000:1996 | Harmonized system of quality assessment for electronic components. Generic specification. Fixed RF wound inductors |
BS EN 147000:1995 | Harmonized system of quality assessment for electronic components. Generic specification. Sockets for use with electrical relays of assessed quality |
BS QC 420000:1992 | Harmonized system of quality assessment for electronic components. Varistors for use in electronic equipment: generic specification |
BS EN 116303:1996 | Harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical all-or-nothing heavy load relays of assessed quality (hermetically sealed, 5A to 25A) |
BS EN 137000:1996 | Harmonized system of quality assessment for electronic components. Generic specification: Fixed aluminium electrolytic a.c. capacitors with non-solid electrolyte for use with motors |
BS QC 390000:1992 | Harmonized system of quality assessment for electronic components. Fixed film resistor networks for use in electronic equipment. Generic specification |
BS QC 221400:1997 | Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 3 mm (0,12 in) with screw coupling. Characteristic impedance 50 ohms (Type SMC) |
BS EN 117000:1997 | Harmonized system of quality assessment for electronic components. Generic specification. Solid state all-or-nothing relays. Generic data and methods of test |
BS 2011-1.1:1983 | Environmental testing General and guidance |
BS CECC 63000:1990 | Harmonized system of quality assessment for electronic components. Generic specification: film and hybrid integrated circuits |
BS CECC 63000:1985 | Harmonized system of quality assessment for electronic components: generic specification: film and hybrid integrated circuits |
BS 9450:1998 | Specification for integrated electronic circuits and micro-assemblies of assessed quality (capability approval procedures). Generic data and methods of test |
BS QC 160000-1:1987 | Harmonized system of quality assessment for electronic components. Electrical relays. Generic specification: electromechanical all-or-nothing relays Test and measurement procedures |
BS QC 221200:1997 | Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock. Characteristic impedance 50 ohms (Type BNC) |
BS EN 116000-3:1996 | Harmonized system of quality assessment for electronic components. Generic specification: electromechanical all-or-nothing relays Test and measurement procedures |
BS EN 120000:1996 | Harmonized system of quality assessment for electronic components. General specification: semiconductor optoelectronic and liquid crystal devices |
BS QC 222400:1997 | Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 5,6 mm (0,22 in). Characteristic impedance 75 ohms (type 1,6/5,6). Characteristic impedance 50 ohms (type 1,8/5,6) with similar mating dimensions |
BS 9400:1970 | Specification for integrated electronic circuits and micro-assemblies of assessed quality (qualification approval procedures): generic data and methods of test |
BS CECC 41400:1980 | Harmonized system of quality assessment for electronic components: sectional specification: rotary precision potentiometers |
BS AU 217-2:1989 | Maximum road speed limiters for motor vehicles Specification for system and component requirements |
BS 9610:1982 | Specification for quartz crystal units of assessed quality: generic data and methods of test |
BS 9500:1990 | Specification for sockets of assessed quality for plug-in electronic components: generic data and methods of test |
BS 9600:1983 | Specification for piezoelectric crystal filters of assessed quality: generic data and methods of test |
BS 4584-103.3:1992 | Metal-clad base materials for printed wiring boards. Special materials used in connection with printed circuits Specification for permanent polymer coating materials (solder resist) for use in the fabrication of printed boards |
BS 5760-13.4:1993 | Reliability of systems, equipment and components. Guide to reliability test conditions for consumer equipment Conditions providing a low degree of simulation for equipment for portable and non-stationary use |
BS QC420100(1992) : 1992 | HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRIC COMPONENTS - VARISTORS FOR USE IN ELECTRONIC EQUIPMENT - SECTIONAL SPECIFICATION FOR SURGE SUPPRESSION VARISTORS |
BS 9940-0:1983 | Harmonized system of quality assessment for electronic components. Fixed resistors for use in electronic equipment Generic specification |
BS QC 760000:1990 | Harmonized system of quality assessment for electronic components. Film and hybrid film integrated circuits. Generic specification |
BS EN 134000:1995 | Harmonized system of quality assessment for electronic components. Generic specification: variable capacitors. (Qualification approval and capability approval) |
BS 7822-3:1995 | Insulation coordination for equipment within low-voltage systems Use of coatings to achieve insulation coordination of printed board assemblies |
BS QC 221300:1997 | Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 3 mm (0,12 in) with snap-on coupling. Characteristic impedance 50 ohms (Type SMB) |
BS CECC 16000-1:1992 | Harmonized system of quality assessment for electronic components. Generic specification: electromechanical all-or-nothing relays General |
BS EN 186000-1:1994 | Harmonized system of quality assessment for electronic components. Generic specification. Connector sets for optical fibres and cables Requirements, test methods and qualification approval procedures |
BS 9930-0(1983) : AMD 5955 | SPECIFICATION FOR HARMONIZED SYSTEM OF QUALITY ASSESSMENT OF ELECTRONIC COMPONENTS - FIXED CAPACITORS FOR USE IN ELECTRONIC COMPONENTS - GENERIC SPECIFICATION |
BS QC 400000:1990 | Harmonized system of quality assessment for electronic components. Fixed resistors for use in electronic equipment: generic specification |
BS 2011-2.2C & D:1981 | Environmental testing. Guidance Tests C & D. Guidance for damp heat tests |
IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.