CEI EN 60300-3-4 : 2010
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
DEPENDABILITY MANAGEMENT - PART 3-4: APPLICATION GUIDE - GUIDE TO THE SPECIFICATION OF DEPENDABILITY REQUIREMENTS
Available format(s)
Hardcopy , PDF
Language(s)
English - Italian
Published date
01-11-2010
Publisher
Superseded date
22-12-2022
Superseded by
Excluding VAT
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General considerations for
dependability specifications
5 Dependability management
6 Availability
7 Reliability
8 Maintainability
9 Maintenance support
Annex A (informative) - Reference
standards for verification
and validation techniques
Annex B (informative) - Examples
of reliability, maintainability,
maintenance support and
availability requirements
Bibliography
Annex ZA (normative) - Normative
references to international
publications with their
corresponding European
publications
This Part of the IEC/EN 60300 series is a Guide for specifying reliability characteristics and indicates the procedures and criteria for verification and validation of the same, and is a complement to the IEC/EN 62347 standard.
| Committee |
CT 56
|
| DevelopmentNote |
Classificazione CEI 56-14. Supersedes CEI 56-14. (06/2008)
|
| DocumentType |
Standard
|
| Pages |
70
|
| PublisherName |
Comitato Elettrotecnico Italiano
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| IEC 60300-3-4:2007 | Identical |
| EN 60300-3-4:2008 | Identical |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| IEC 60605-3-5:1996 | Equipment reliability testing - Part 3: Preferred test conditions - Section 5: Test cycle 5: Ground mobile equipment - Low degree of simulation |
| IEC 60605-3-2:1986 | Equipment reliability testing. Part 3: Preferred test conditions. Equipment for stationary use in weatherprotected locations - High degree of simulation |
| IEC 61123:1991 | Reliability testing - Compliance test plans for success ratio |
| IEC 60605-4:2001 | Equipment reliability testing - Part 4: Statistical procedures for exponential distribution - Point estimates, confidence intervals, prediction intervals and tolerance intervals |
| IEC 62308:2006 | Equipment reliability - Reliability assessment methods |
| IEC 60605-3-6:1996 | Equipment reliability testing - Part 3: Preferred test conditions - Section 6: Test cycle 6: Outdoor transportable equipment - Low degree of simulation |
| IEC 60605-3-3:1992 | Equipment reliability testing - Part 3: Preferred test conditions - Section 3: Test Cycle 3: Equipment for stationary use in partially weatherprotected locations - Low degree of simulation |
| IEC 62198:2013 | Managing risk in projects - Application guidelines |
| EN 60300-3-2:2005 | Dependability management - Part 3-2: Application guide - Collection of dependability data from the field |
| CEI 56-31 : 1ED 2000 | ANALISI DELL'ALBERO DEI GUASTI |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 60300-3-3:2017 | Dependability management - Part 3-3: Application guide - Life cycle costing |
| IEC 61649:2008 | Weibull analysis |
| IEC 60300-3-12:2011 | Dependability management - Part 3-12: Application guide - Integrated logistic support |
| IEC 60605-3-4:1992 | Equipment reliability testing - Part 3: Preferred test conditions - Section 4: Test cycle 4: Equipment for portable and non-stationary use - Low degree of simulation |
| IEC 61014:2003 | Programmes for reliability growth |
| IEC 60300-3-14:2004 | Dependability management - Part 3-14: Application guide - Maintenance and maintenance support |
| CEI 56-25 : 1ED 2000 | Equipment Maintainability Guide Part 3: Sections 6 and 7: Verification, Collection, Analysis and Presentation of Data |
| IEC 60605-6:2007 | Equipment reliability testing - Part 6: Tests for the validity and estimation of the constant failure rate and constant failure intensity |
| CEI 56-34 : 1ED 2000 | PROVE DI AFFIDABILITA - PROVE DI CONFORMITA PER TASSI DI GUASTI E INTENSITA COSTANTI |
| CEI 56-13 : 1ED 1999 | Managing Trustworthiness Part 3: Application Guide Section 3 : Lifecycle Cost |
| IEC 60706-3:2006 | Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data |
| EN 60300-1:2014 | Dependability management - Part 1: Guidance for management and application |
| IEC 61160:2005 | Design review |
| EN 60706-2:2006 | Maintainability of equipment - Part 2: Maintainability requirements and studies during the design and development phase |
| IEC 61070:1991 | Compliance test procedures for steady-state availability |
| IEC 61078:2016 | Reliability block diagrams |
| IEC 61165:2006 | Application of Markov techniques |
| CEI 56-37 : 1ED 2000 | CRESCITA DELLA AFFIDABILITA - PROVE E METODI DI VALUTAZIONE STATISTICA |
| IEC 60605-3-1:1986 | Equipment reliability testing. Part 3: Preferred test conditions. Indoor portable equipment - Low degree of simulation |
| EN 60706-3:2006 | Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data |
| EN 62347:2007 | Guidance on system dependability specifications |
| EN 60300-3-1:2004 | Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
| EN 60300-3-12:2011 | Dependability management - Part 3-12: Application guide - Integrated logistic support |
| EN 61078 : 1991 | RELIABILITY BLOCK DIAGRAMS (IEC 61078:2016) |
| IEC 61163-1:2006 | Reliability stress screening - Part 1: Repairable assemblies manufactured in lots |
| CEI 56-27 : 1ED 2000 | GUIDA SULLA MANUTENIBILITA DELLA APPARECCHIATURA - PARTE 5: SEZIONE 4: PROVE PER LA DIAGNOSTICA |
| EN 60300-3-14:2004 | Dependability management - Part 3-14: Application guide - Maintenance and maintenance support |
| EN 60300-3-3:2017 | Dependability management - Part 3-3: Application guide - Life cycle costing |
| IEC 61163-2:1998 | Reliability stress screening - Part 2: Electronic components |
| IEC 62347:2006 | Guidance on system dependability specifications |
| IEC 60300-3-2:2004 | Dependability management - Part 3-2: Application guide - Collection of dependability data from the field |
| IEC 61124:2012 | Reliability testing - Compliance tests for constant failure rate and constant failure intensity |
| IEC 60300-3-1:2003 | Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
| CEI 56-24 : 1ED 2000 | Equipment Maintainability GuidePart 2: Section 5 - Maintainability Studies in the Design Phase |
| IEC 61164:2004 | Reliability growth - Statistical test and estimation methods |
| IEC 61703:2016 | Mathematical expressions for reliability, availability, maintainability and maintenance support terms |
| IEC 61709:2017 | Electric components - Reliability - Reference conditions for failure rates and stress models for conversion |
| EN 61025:2007 | Fault tree analysis (FTA) |
| IEC 60300-1:2014 | Dependability management - Part 1: Guidance for management and application |
| IEC 60300-3-7:1999 | Dependability management - Part 3-7: Application guide - Reliability stress screening of electronic hardware |
| IEC 60605-2:1994 | Equipment reliability testing - Part 2: Design of test cycles |
| IEC 60706-2:2006 | Maintainability of equipment - Part 2: Maintainability requirements and studies during the design and development phase |
| IEC 60300-2:2004 | Dependability management - Part 2: Guidelines for dependability management |
| IEC 60300-3-10:2001 | Dependability management - Part 3-10: Application guide - Maintainability |
| IEC 61713:2000 | Software dependability through the software life-cycle processes- Application guide |
| EN 61014:2003 | Programmes for reliability growth |
| IEC 60706-5:2007 | Maintainability of equipment - Part 5: Testability and diagnostic testing |
| EN 61160:2005 | Design review |
| CEI 56-16 : 1ED 1999 | Project and design review<br> |
| IEC 61650:1997 | Reliability data analysis techniques - Procedures for comparison of two constant failure rates and two constant failure (event) intensities |
| EN 61164:2004 | Reliability growth - Statistical test and estimation methods |
| EN 60300-2:2004 | Dependability management - Part 2: Guidelines for dependability management |
| EN 62308:2006 | Equipment reliability - Reliability assessment methods |
| EN 61124:2012 | Reliability testing - Compliance tests for constant failure rate and constant failure intensity |
| EN 60706-5:2007 | Maintainability of equipment - Part 5: Testability and diagnostic testing |
| IEC 61710:2013 | Power law model - Goodness-of-fit tests and estimation methods |
| CEI 56-10 : 1ED 1997 | Trust ManagementPart 3: Application GuideSection 1: Trust Analysis Techniques: Methodology Guide |
| EN 61703:2016 | Mathematical expressions for reliability, availability, maintainability and maintenance support terms |
| CEI 56-12 : 1ED 1999 | Trust Management Part 3: Application Guide Section 2: Collecting Trust Data from the Field |
| IEC 60300-3-5:2001 | Dependability management - Part 3-5: Application guide - Reliability test conditions and statistical test principles |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.