CSA B51 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE
Hardcopy , PDF
23-04-2019
English, French
01-01-2014
Preface
B51-14, Part 1, General requirements for boilers, pressure
vessels, and pressure piping
1 Scope
2 Reference publications
3 Definitions
4 General requirements
5 Identification
6 Boilers and related components
7 Pressure vessels
8 Piping and fittings
9 Refrigeration equipment
10 Fired-heater pressure coils in petroleum and chemical
plant service
11 Repairs and alterations
12 Pressure relief devices
13 In-service inspection
Annexes
A (informative) - Burial of pressure vessels
B (informative) - Quality control program for defect
prevention and in-service reliability
C (informative) - Guidelines for safety valve, relief
valve, and safety relief valve repair organizations
D (informative) - Sample forms
E (informative) - Inspection of welds in pressure coils
exposed to direct radiant heat
F (informative) - Quality control program for
manufacturers of fittings
G (normative) - Automotive propane vessel standards
H (informative) - Overpressure protection devices
I (normative) - Historical boilers
J (normative) - Requirements regarding the use of
finite element analysis (FEA) to support a pressure
equipment design submission
B51-14, Part 2, High-pressure cylinders for the on-board
storage of natural gas and hydrogen as fuels
for automotive vehicles
0 Introduction
1 Scope
2 Reference publications
3 Definitions
4 Service conditions
5 Design approval
6 Requirements applicable to all cylinder types
7 Type 1 metal cylinders
8 Type 2 hoop-wrapped cylinders
9 Type 3 fully wrapped cylinders
10 Type 4 all-composite cylinders
11 Marking
12 Preparation for dispatch
13 Quality control
14 Test methods
Annexes
A (informative) - Report forms
B (informative) - Procedure for requalifying all-steel
natural gas vehicle storage cylinders
B51-14, Part 3, Compressed natural gas and hydrogen
refuelling station pressure piping systems
and ground storage vessels
1 Scope
2 Reference publications
3 Definition
4 General requirements
5 Compressed natural gas and hydrogen refuelling station
pressure piping systems
6 Compressed natural gas and hydrogen refuelling station
ground storage vessels
Contains: B51-14, Part 1 - General requirements for boilers, pressure vessels, and pressure piping; B51-14, Part 2 - High-pressure cylinders for the on-board storage of natural gas and hydrogen as fuels for automotive vehicles; and B51-14, Part 3 - Compressed natural gas and hydrogen refuelling station pressure piping systems and ground storage vessels.
DevelopmentNote |
2009 Edition is still active in English & French version. A safety bulletin exists for this standard. (03/2014) French Edition issued on 01-07-2014. (08/2014)
|
DocumentType |
Revision
|
ISBN |
978-1-7139-722-3
|
Pages |
174
|
PublisherName |
Canadian Standards Association
|
Status |
Superseded
|
SupersededBy |
PD ISO/TR 13086-1:2011 | Gas cylinders. Guidance for design of composite cylinders Stress rupture of fibres and burst ratios related to test pressure |
CSA E335.2.20 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR BATTERY POWERED TOOTH BRUSHES AND THEIR CHARGING AND BATTERY ASSEMBLIES |
CSA E730.2.3 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
CSA Z314.7 : 2003(R2018) | STEAM STERILIZERS FOR HEALTH CARE FACILITIES |
CSA E335.2.71 : 1995 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR ELECTRICAL HEATING APPLIANCES FOR BREEDING AND REARING ANIMALS |
CSA M424.1 : 2016 | FLAMEPROOF NON-RAIL-BOUND DIESEL-POWERED MACHINES FOR USE IN GASSY UNDERGROUND COAL MINES |
CSA N285.0 : 2006 | GENERAL REQUIREMENTS FOR PRESSURE-RETAINING SYSTEMS AND COMPONENTS IN CANDU NUCLEAR POWER PLANTS |
CSA E730.1 : 0 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - GENERAL REQUIREMENTS |
CSA E742 : 1994 | ISOLATING TRANSFORMERS AND SAFETY ISOLATING TRANSFORMERS - REQUIREMENTS |
CSA E79.18 : 1995 | ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ENCAPSULATION "M" |
CSA E335.2.24 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR REFRIGERATORS, FOOD-FREEZERS AND ICE-MAKERS |
CSA E335.1-2E : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 1: GENERAL REQUIREMENTS |
CSA E730.2.7 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR TIMERS AND TIME SWITCHES |
CSA Z10083 : 2008 | OXYGEN CONCENTRATOR SUPPLY SYSTEMS FOR USE WITH MEDICAL GAS PIPELINE SYSTEMS |
CSA E61241.1.1 : 2002 : R2010 | ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 1-1: ELECTRICAL APPARATUS PROTECTED BY ENCLOSURES AND SURFACE TEMPERATURE LIMITATION - SPECIFICATION FOR APPARATUS |
CSA E335.2.5 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR DISHWASHERS |
CSA E335.2.15 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR APPLIANCES FOR HEATING LIQUIDS |
CSA C22.2 No. 1335.1 : 1993 : R2004 | PORTABLE ELECTRICAL MOTOR-OPERATED AND HEATING APPLIANCES: GENERAL REQUIREMENTS |
CSA 12.8 : 2002 : R2013 | STANDARD FOR NATURAL GAS VEHICLE FUELING STATION RECIPROCATING COMPRESSOR GUIDELINES |
CSA/ANSI NGV4.8 :2012 | STANDARD FOR NATURAL GAS VEHICLE FUELING STATION RECIPROCATING COMPRESSOR GUIDELINES |
CSA C22.2 No. 140.3 : 2015 | REFRIGERANT-CONTAINING COMPONENTS FOR USE IN ELECTRICAL EQUIPMENT |
CSA Z314.7 : 2003 : R2013 | STEAM STERILIZERS FOR HEALTH CARE FACILITIES |
CSA Z314.7 : 2003 | STEAM STERILIZERS FOR HEALTH CARE FACILITIES |
CSA Z662.1 : 2013 | COMMENTARY ON CSA Z662-07, OIL AND GAS PIPELINE SYSTEMS |
BS EN ISO 7396-1:2016 | Medical gas pipeline systems Pipeline systems for compressed medical gases and vacuum |
Z276-18 | Liquefied natural gas (LNG) - Production, storage, and handling |
CSA C22.2 No. 62282-2 : 2007 : R2013 | FUEL CELL TECHNOLOGIES - PART 2: FUEL CELL MODULES |
CSA E335.2.2 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR VACUUM CLEANERS AND WATER SUCTION CLEANING APPLIANCES |
ISO/TR 13086-1:2011 | Gas cylinders - Guidance for design of composite cylinders Part 1: Stress rupture of fibres and burst ratios related to test pressure |
NFPA 30 : 2018 | FLAMMABLE AND COMBUSTIBLE LIQUIDS CODE |
NFPA 122 : 2015 | FIRE PREVENTION AND CONTROL IN METAL/NONMETAL MINING AND METAL MINERAL PROCESSING FACILITIES |
NFPA 1192 : 2018 | RECREATIONAL VEHICLES |
NFPA 59 : 2018 | UTILITY LP-GAS PLANT CODE |
CSA C22.2 No. 104 : 2011 : R2015 | HUMIDIFIERS |
EN 62282-2:2012 | Fuel cell technologies - Part 2: Fuel cell modules |
CSA 2.33 : 2017 | VENTED GAS FIREPLACE HEATERS |
NFPA 59:2024 | Utility LP-Gas Plant Code |
CSA E335.2.55 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRICAL APPLIANCES FOR USE WITH AQUARIUMS AND GARDEN PONDS |
CSA E335.2.4 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR SPIN EXTRACTORS |
CSA B140.7.2 : 1967 | OIL-FIRED STEAM AND HOT-WATER BOILERS FOR COMMERCIAL AND INDUSTRIAL USE |
CSA E335.2.65 : 1995 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR AIR-CLEANING APPLIANCES |
17/30293100 DC : 0 | BS ISO 19882 - GASEOUS HYDROGEN - THERMALLY ACTIVATED PRESSURE RELIEF DEVICES FOR COMPRESSED HYDROGEN VEHICLE FUEL CONTAINERS |
CNG FUEL INSPECTOR RESOURCE PACKAGE : 2013 | CONSISTS OF ANSI NGV 1-2006/CSA NGV 1-2006, COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES; ANSI PRD 1-2013, PRESSURE RELIEF DEVICES FOR NATURAL GAS VEHICLE (NGV) FUEL CONTAINERS; ANSI NGV 2-2007, COMPRESSED NATURAL GAS VEHICLE FUEL CONTAINERS; ANSI NGV 2A-2012, ADDENDA 1 TO ANSI NGV 2-2007, COMPRESSED NATURAL GAS VEHICLE FUEL CONTAINERS AND ANSI NGV 2B-2012 |
CSA E335.2.19 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR BATTERY POWERED SHAVERS, HAIR CLIPPERS AND SIMILAR APPLIANCES AND THEIR CHARGING AND BATTERY ASSEMBLIES |
CSA E730.2.12 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRICALLY OPERATED DOOR LOCKS |
CSA E335.2.57 : 1994 : R2004 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR ICE CREAM APPLIANCES WITH INCORPORATED MOTOR COMPRESSORS |
CSA E60335.1/4E : 2003 : R2007 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS |
I.S. EN ISO 7396-1:2016 | MEDICAL GAS PIPELINE SYSTEMS - PART 1: PIPELINE SYSTEMS FOR COMPRESSED MEDICAL GASES AND VACUUM (ISO 7396-1:2016) |
CSA E730.2.12 : 1994 : INC : AMD 1 : 2001 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRICALLY OPERATED DOOR LOCKS |
CSA E60335.1/4E :2003 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS |
CSA/ANSI NGV4.8 : 2012 : R2013 | STANDARD FOR NATURAL GAS VEHICLE FUELING STATION RECIPROCATING COMPRESSOR GUIDELINES |
CSA B140.0 : 2003 : R2013 | OIL-BURNING EQUIPMENT: GENERAL REQUIREMENTS |
CSA 1.8 : 2016 | GAS FOOD SERVICE EQUIPMENT |
CSA Z142 : 2010 : R2014 | CODE FOR POWER PRESS OPERATION: HEALTH, SAFETY, AND SAFEGUARDING REQUIREMENTS |
CSA 4.9 : 2017 | GAS-FIRED LOW PRESSURE STEAM AND HOT WATER BOILERS |
CSA E730.2.12 : 1994 : R2013 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRICALLY OPERATED DOOR LOCKS |
CSA/ANSI NGV 4.1-2018 | Natural gas vehicle (NGV) dispensing systems |
CSA C22.2 No. 1335.1 : 1993(R2008) | PORTABLE ELECTRICAL MOTOR-OPERATED AND HEATING APPLIANCES: GENERAL REQUIREMENTS |
CSA/ANSI Z21.13 : 2017 | GAS-FIRED LOW PRESSURE STEAM AND HOT WATER BOILERS |
CSA E730.2.6 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR AUTOMATIC ELECTRICAL PRESSURE SENSING CONTROLS INCLUDING MECHANICAL REQUIREMENTS |
CSA Z662 PACKAGE : 2011 | CONSISTS OF Z662-11, OIL AND GAS PIPELINE SYSTEMS AND Z662.1-11, COMMENTARY ON CSA Z662-11, OIL AND GAS PIPELINE SYSTEMS |
CSA Z314.1:2009 | ETHYLENE OXIDE STERILIZERS FOR HEALTH CARE FACILITIES |
CSA B140.7 : 2005 : R2010 | OIL-BURNING EQUIPMENT: STEAM AND HOT-WATER BOILERS |
Z7396.1-17 | Medical gas pipeline systems - Part 1: Pipelines for medical gases, medical vacuum, medical support gases, and anaesthetic gas scavenging systems |
CSA Z8002 : 2014(R2018) | OPERATION AND MAINTENANCE OF HEALTH CARE FACILITIES |
CSA E730.2.1 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRICAL CONTROLS FOR ELECTRICAL HOUSEHOLD APPLIANCES |
CSA E79.6 : 0 | ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - OIL-IMMERSED APPARATUS |
CSA C22.2 No. 125 : 1984 : INC : AMD 2 : 1986 | ELECTROMEDICAL EQUIPMENT |
NFPA 59A : 2016 | PRODUCTION, STORAGE, AND HANDLING OF LIQUEFIED NATURAL GAS (LNG) |
NFPA 120 : 2015 | FIRE PREVENTION AND CONTROL IN COAL MINES |
CSA HPIT 1 : 2015 | COMPRESSED HYDROGEN POWERED INDUSTRIAL TRUCK ON-BOARD FUEL STORAGE AND HANDLING COMPONENTS |
CSA HPIT 1:15 (R2020) | Compressed hydrogen powered industrial truck on-board fuel storage and handling components |
CSA B366.1 :2011 : INC : UPD 1 : 2014 | SOLID-FUEL-FIRED CENTRAL HEATING APPLIANCES |
CSA B366.1 : 2011 | SOLID-FUEL-FIRED CENTRAL HEATING APPLIANCES |
ANSI/CSA NGV 5.1-2016 (R2020) | Residential fueling appliances |
I.S. EN 62282-2:2012 | FUEL CELL TECHNOLOGIES - PART 2: FUEL CELL MODULES (IEC 62282-2:2012 (EQV)) |
CSA/ANSI Z83.11 : 2016 | GAS FOOD SERVICE EQUIPMENT |
CEI EN 62282-2 : 2013 | FUEL CELL TECHNOLOGIES - PART 2: FUEL CELL MODULES |
CSA NGV 5.1 : 2016 | RESIDENTIAL FUELING APPLIANCES |
CSA E730.2.4 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PARTICULAR REQUIREMENTS FOR THERMAL MOTOR PROTECTORS FOR MOTOR COMPRESSORS OF HERMETIC AND SEMI HERMETIC TYPE |
CSA E335.2.33 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR COFFEE MILLS AND COFFEE GRINDERS |
CSA Z318.6 : 0 | COMMISSIONING OF MEDICAL GAS SYSTEMS IN HEALTH CARE FACILITIES |
CSA E335.1-3E : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 1: GENERAL REQUIREMENTS |
CSA E335.2.14 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRIC KITCHEN MACHINES |
13/30255929 DC : 0 | BS EN ISO 7396-1 - MEDICAL GAS PIPELINE SYSTEMS - PART 1: PIPELINE SYSTEMS FOR COMPRESSED MEDICAL GASES AND VACUUM |
CSA E491 : 1994 | SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES |
CSA NGV 4.3-2018 | Temperature compensation guideline for compressed natural gas vehicle fueling |
CSA E335.2.61 : 1995 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR THERMAL STORAGE HEATERS |
CSA E691 : 0 | THERMAL LINKS - REQUIREMENTS AND APPLICATION GUIDE |
CSA N285.3 : 0 | REQUIREMENTS FOR CONTAINMENT SYSTEMS COMPONENTS IN CANDU NUCLEAR POWER PLANTS |
CSA 12.8 :2002 | STANDARD FOR NATURAL GAS VEHICLE FUELING STATION RECIPROCATING COMPRESSOR GUIDELINES |
CSA E335.2.70 : 95(R2004) | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR MILKING MACHINES |
CSA C22.2 No. 62282-3-100 : 2015 | FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
ANSI Z21.88 : 2017 | VENTED GAS FIREPLACE HEATERS |
CSA 12.5 : 1999 : R2014 | NGV DISPENSING SYSTEMS |
CSA Z275.1 : 2016 | HYPERBARIC FACILITIES |
C22.2 NO. 109-17 | Commercial cooking appliances |
CSA B108 : 2014 | COMPRESSED NATURAL GAS FUELLING STATIONS INSTALLATION CODE |
CSA C22.2 No. 309 : 2016 | INDUSTRIAL CLOTHES DRYERS |
CSA Z267 : 2000 | SAFETY CODE FOR AMUSEMENT RIDES AND DEVICES |
ANSI HPRD 1 : 2013(R 2018) | THERMALLY ACTIVATED PRESSURE RELIEF DEVICES FOR COMPRESSED HYDROGEN VEHICLE FUEL CONTAINERS |
CSA E335.2.63 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR COMMERCIAL ELECTRIC WATER BOILERS AND LIQUID HEATERS |
CSA Z305.1 : 0 | NONFLAMMABLE MEDICAL GAS PIPING SYSTEMS |
DIN EN ISO 7396-1:2016-09 | MEDICAL GAS PIPELINE SYSTEMS - PART 1: PIPELINE SYSTEMS FOR COMPRESSED MEDICAL GASES AND VACUUM (ISO 7396-1:2016) |
CAN/CSA-Z662-15 | Oil and gas pipeline systems |
CSA B140.7:2005 | OIL-BURNING EQUIPMENT: STEAM AND HOT-WATER BOILERS |
CSA B140.7 : 2005 : R2014 | OIL-BURNING EQUIPMENT: STEAM AND HOT-WATER BOILERS |
N285.0-17/N285.6 SERIES-17 | General requirements for pressure-retaining systems and components in CANDU nuclear power plants / Material Standards for reactor components for CANDU nuclear power plants |
CSA C22.2 No. 125 : 1984 : R1992 | ELECTROMEDICAL EQUIPMENT |
CSA C22.2 No. 68 : 2000( R2014) | MOTOR-OPERATED APPLIANCES (HOUSEHOLD AND COMMERCIAL) |
CSA C22.2 No. 139 : 2013 : R2018 | ELECTRICALLY OPERATED VALVES |
CSA Z305.6 : 1992 | MEDICAL OXYGEN CONCENTRATOR CENTRAL SUPPLY SYSTEM FOR USE WITH NONFLAMMABLE MEDICAL GAS PIPING SYSTEMS |
CSA B366.1 : 2011 : R2015 | SOLID-FUEL-FIRED CENTRAL HEATING APPLIANCES |
CSA N290.8 : 2015 | TECHNICAL SPECIFICATION REQUIREMENTS FOR NUCLEAR POWER PLANT COMPONENTS |
CSA B139 : 2015 | INSTALLATION CODE FOR OIL-BURNING EQUIPMENT |
ASHRAE HDBK REFRIGERATION : 2014 | ASHRAE HANDBOOK - REFRIGERATION |
CSA E335.2.18 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - GUIDE FOR PREPARING SAFETY REQUIREMENTS FOR BATTERY POWERED MOTOR OPERATED APPLIANCES AND THEIR CHARGING BATTERY ASSEMBLIES |
CSA E335.2.53 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRIC SAUNA HEATING APPLIANCES |
CSA E342.1 : 1995 | SAFETY REQUIREMENTS FOR ELECTRIC FANS AND REGULATORS - PART 1: FANS AND REGULATORS FOR HOUSEHOLD AND SIMILAR PURPOSES |
C22.2 NO. 22-18 | Electrical equipment for flammable and combustible fuel dispensers |
CSA B140.7.1 : 76(R2001) | OIL-FIRED STEAM AND HOT-WATER BOILERS FOR RESIDENTIAL USE |
CSA M424.2 : 2016 | NON-RAIL-BOUND DIESEL-POWERED MACHINES FOR USE IN NON-GASSY UNDERGROUND MINES |
CSA B109 : 2017 | NATURAL GAS FOR VEHICLES INSTALLATION CODE |
B52HB-16 | A practical handbook for implementing CSA B52-13, Mechanical refrigeration code |
CSA Z275.2 : 2015 | OCCUPATIONAL SAFETY CODE FOR DIVING OPERATIONS |
CSA E335.2.13 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR DEEP FAT FRYERS, FRYING PANS AND SIMILAR APPLIANCES |
CSA E257 : 0 | FUSEHOLDERS FOR MINIATURE CARTRIDGE FUSE-LINKS |
CSA C22.2 No. 151 : 1986 | LABORATORY EQUIPMENT |
CSA B140.12 : 2003 : R2013 | OIL-BURNING EQUIPMENT: SERVICE WATER HEATERS FOR DOMESTIC HOT WATER, SPACE HEATING, AND SWIMMING POOLS |
CSA 12.6 :2004 | VEHICLE REFUELLING APPLIANCES |
CSA E335.2.3 : 1994 : R2004 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRIC IRONS |
CSA E335.2.12 : 1994 : R2004 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR WARMING PLATES AND SIMILAR APPLIANCES |
CSA B140.12:2003 | OIL-BURNING EQUIPMENT: SERVICE WATER HEATERS FOR DOMESTIC HOT WATER, SPACE HEATING, AND SWIMMING POOLS |
CSA C22.2 No. 1335.1 : 1993(R2013) | PORTABLE ELECTRICAL MOTOR-OPERATED AND HEATING APPLIANCES: GENERAL REQUIREMENTS |
CSA E335.2.10 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES AND WET SCRUBBING MACHINES |
CSA E335.2.5 : 1994 : R2004 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR DISHWASHERS |
CSA B140.0 : 2003 | OIL-BURNING EQUIPMENT: GENERAL REQUIREMENTS |
CSA E61241.1.1 : 2002 | ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 1-1: ELECTRICAL APPARATUS PROTECTED BY ENCLOSURES AND SURFACE TEMPERATURE LIMITATION - SPECIFICATION FOR APPARATUS |
CSA C22.2 No. 120 : 2013 | REFRIGERATION EQUIPMENT |
B365-17 | Installation code for solid-fuel-burning appliances and equipment |
CSA 12.5 : 1999 : R2004 | NGV DISPENSING SYSTEMS |
CSA CGA B105 : 1993 | CODE FOR DIGESTER GAS AND LANDFILL GAS INSTALLATIONS |
CSA C22.2 No. 68 : 2009 : INC : UPD 2 : 2010 | MOTOR-OPERATED APPLIANCES (HOUSEHOLD AND COMMERCIAL) |
CSA C22.2 No. 139 : 2013 | ELECTRICALLY OPERATED VALVES |
UNE-EN ISO 7396-1:2016 | Medical gas pipeline systems - Part 1: Pipeline systems for compressed medical gases and vacuum (ISO 7396-1:2016) |
ISO 7396-1:2016 | Medical gas pipeline systems — Part 1: Pipeline systems for compressed medical gases and vacuum |
CSA B149HB : 2005 | NATURAL GAS AND PROPANE CODE HANDBOOK |
CSA Z240 RV SERIES : 2014 | RECREATIONAL VEHICLES |
CSA B149.2:20 | Propane storage and handling code |
CSA B149.1 : 2010 : R2015 | NATURAL GAS AND PROPANE INSTALLATION CODE |
CSA B149.1 : 2010 | NATURAL GAS AND PROPANE INSTALLATION CODE |
CSA C22.2 No. 104:2011 | HUMIDIFIERS |
IEC 62282-2:2012 | Fuel cell technologies - Part 2: Fuel cell modules |
CSA C22.2 No. 104 : 2011 : INC : UPD 1 : 2016 : R201500 | HUMIDIFIERS |
BS EN 62282-2:2012 | Fuel cell technologies Fuel cell modules |
UNE-EN 62282-2:2012 | Fuel cell technologies - Part 2: Fuel cell modules |
CSA Z314.1 : 2009 : R2013 | ETHYLENE OXIDE STERILIZERS FOR HEALTH CARE FACILITIES |
CSA S500 : 2014 | THERMOSYPHON FOUNDATIONS FOR BUILDINGS IN PERMAFROST REGIONS |
EN ISO 7396-1:2016 | Medical gas pipeline systems - Part 1: Pipeline systems for compressed medical gases and vacuum (ISO 7396-1:2016) |
C22.2 NO. 165-17 | Electric boilers |
CSA E335.2.9 : 0 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR TOASTERS, GRILLS, ROASTERS AND SIMILAR APPLIANCES |
CSA 12.6 : 2004 : R2014 | VEHICLE REFUELLING APPLIANCES |
CSA B140.7 : 2005 : R2010 : FR | OIL-BURNING EQUIPMENT: STEAM AND HOT-WATER BOILERS |
CSA E730.2.5 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR AUTOMATIC ELECTRICAL BURNER CONTROL SYSTEMS |
CSA E335.2.31 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR RANGE HOODS |
CSA E335.2.59 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR INSECT KILLERS |
CSA E335.2.10 : 1994 : R2004 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES AND WET SCRUBBING MACHINES |
CSA E730.2.10 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRICALLY OPERATED MOTOR STARTING RELAYS |
CSA E335.2.12 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR WARMING PLATES AND SIMILAR APPLIANCES |
CSA Z10083 : 2008 : R2013 | OXYGEN CONCENTRATOR SUPPLY SYSTEMS FOR USE WITH MEDICAL GAS PIPELINE SYSTEMS |
CSA Z142 : 2010 : FR | CODE FOR POWER PRESS OPERATION: HEALTH, SAFETY, AND SAFEGUARDING REQUIREMENTS |
CSA E730.2.12 : 1994 : INC : AMD 1 : 2001 : R2013 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRICALLY OPERATED DOOR LOCKS |
CSA/ANSI NGV4.8 : 2012 : R2016 | STANDARD FOR NATURAL GAS VEHICLE FUELING STATION RECIPROCATING COMPRESSOR GUIDELINES |
CSA 12.8 : 2002 : R2016 | STANDARD FOR NATURAL GAS VEHICLE FUELING STATION RECIPROCATING COMPRESSOR GUIDELINES |
CSA C22.2 No. 68 : 2009 | MOTOR-OPERATED APPLIANCES (HOUSEHOLD AND COMMERCIAL) |
CSA A5-A8-A362 : 1998 | PORTLAND CEMENT; MASONRY CEMENT; BLENDED HYDRAULIC CEMENT |
C22.2 NO. 236-15 | Heating and cooling equipment (Bi-national standard with UL 1995) |
CSA E335.2.57 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR ICE CREAM APPLIANCES WITH INCORPORATED MOTOR COMPRESSORS |
CSA Z142 :2010 | CODE FOR POWER PRESS OPERATION: HEALTH, SAFETY, AND SAFEGUARDING REQUIREMENTS |
CSA E335.2.3 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR ELECTRIC IRONS |
CSA C22.2 No. 60335-2-89 : 2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-89: PARTICULAR REQUIREMENTS FOR COMMERCIAL REFRIGERATING APPLIANCES WITH AN INCORPORATED OR REMOTE REFRIGERANT UNIT OR COMPRESSOR |
CSA/ANSI Z21.96 : 2014 | PORTABLE WATER HEATERS FOR OUTDOOR USE |
CSA A3000 : 2013 | CEMENTITIOUS MATERIALS COMPENDIUM |
CSA Z180.1 : 2013 | COMPRESSED BREATHING AIR AND SYSTEMS |
CSA 11-6 : 2014 | PORTABLE WATER HEATERS FOR OUTDOOR USE |
CSA C22.2 No. 62282-2 :2007 | FUEL CELL TECHNOLOGIES - PART 2: FUEL CELL MODULES |
CSA E335.2.23 : 1994 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PART 2: PARTICULAR REQUIREMENTS FOR APPLIANCES FOR SKIN OR HAIR CARE |
CSA E335.2.66 : 1995 | SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - PARTICULAR REQUIREMENTS FOR WATER-BED HEATERS |
SAE J2601/2_201409 | Fueling Protocol for Gaseous Hydrogen Powered Heavy Duty Vehicles |
CSA C22.2 No. 125 : 1984 | ELECTROMEDICAL EQUIPMENT |
CSA C22.2 NO. 81:14 (R2019) | Electric irons |
CSA E384.14.1 : 1995 | FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 14: BLANK DETAIL SPECIFICATION: FIXED CAPACITORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION AND CONNECTION TO THE SUPPLY MAINS - ASSESSMENT LEVEL D |
CSA E60079.1 : 2002 | ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - CONSTRUCTION AND VERIFICATION TEST OF FLAMEPROOF ENCLOSURES OF ELECTRICAL APPARATUS |
CSA B149.2 : 2010 : R2015 | PROPANE STORAGE AND HANDLING CODE |
CSA B149.2:2010 | PROPANE STORAGE AND HANDLING CODE |
CSA Z240 VC SERIES : 2014 | |
CSA E730.2.2 : 1994 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR THERMAL MOTOR PROTECTORS |
CSA Z241 SERIES : 2003 : INC : UPD 2 : 2013 : R201300 | PARK MODEL TRAILERS |
CSA E1029.2.4 : 1994 : INC : AMD 1 : 2006 : R2017 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-4: PARTICULAR REQUIREMENTS FOR BENCH GRINDERS |
CAN/CSA-E1029-2-2-94 (R2017) | Safety of Transportable Motor-Operated Electric Tools - Part 2: Particular Requirements for Radial Arm Saws (Adopted IEC 1029-2-2:1993, first edition)| Sécurité des machines-outils électriques semi-fixes - Partie 2: Règles particulières pour les scies radiales (norme CEI 1029-2-2:1993 adoptée, première édition) |
CSA E967 : 1994 | SAFETY OF ELECTRICALLY HEATED BLANKETS, PADS AND SIMILAR FLEXIBLE HEATING APPLIANCES FOR HOUSEHOLD USE |
CAN/CSA-E1029-2-7-94 (R2017) | Safety of Transportable Motor-Operated Electric Tools - Part 2: Particular Requirements for Diamond Saws With Water Supply (Adopted IEC 1029-2-7:1993, first edition) | Sécurité des machines-outils électriques semi-fixes - Partie 2: Règles particulières pour les tronçonneuses à béton (norme CEI 1029-2-7:1993 adoptée, première édition) |
CAN/CSA-E1029-2-6-94 (R2017) | Safety of Transportable Motor-Operated Electric Tools - Part 2: Particular Requirements for Diamond Drills With Water Supply (Adopted IEC 1029-2-6:1993, first edition) | Sécurité des machines-outils électriques semi-fixes - Partie 2: Règles particulières pour les foreuses à béton (norme CEI 1029-2-6:1993 adoptée, première édition) |
CSA E1029.2.1 : 1994 : INC : AMD 2 : 2006 : R2017 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-1: PARTICULAR REQUIREMENTS FOR CIRCULAR SAWS |
CSA E1029.2.5 : 1994 : INC : AMD 1 : 2006 : R2017 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS |
CSA SPE.1000 : 2013 | MODEL CODE FOR THE FIELD EVALUATION OF ELECTRICAL EQUIPMENT |
CSA FC 3 : 2004 | PORTABLE FUEL CELL POWER SYSTEMS |
CSA E1029.2.3 : 1994 : INC : AMD 1 : 2006 : R2017 | Amendment 1:2006 to CAN/CSA-E1029-2-3-94, Safety of Transportable Motor-Operated Electric Tools - Part 2-3: Particular Requirements for Planers and Thicknessers (Adopted Amendment 1:2001 to CEI/IEC 1029-2-3:1993) |
CSA E1029.2.7 : 1994 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2: PARTICULAR REQUIREMENTS FOR DIAMOND SAWS WITH WATER SUPPLY |
ANSI/CSA AMERICA FC 3-2004 (R2017) | PORTABLE FUEL CELL POWER SYSTEMS |
CSA E1029.2.1 : 1994 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-1: PARTICULAR REQUIREMENTS FOR CIRCULAR SAWS |
CSA Z241 SERIES : 2003 : INC : UPD 2 : 2013 : R200800 | PARK MODEL TRAILERS |
NFPA 1192 : 2021 | Standard on Recreational Vehicles |
CSA/ANSI HGV 2 : 2014 | COMPRESSED HYDROGEN GAS VEHICLE FUEL CONTAINERS |
CSA E1029.2.1 : 1994 : INC : AMD 2 : 2006 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-1: PARTICULAR REQUIREMENTS FOR CIRCULAR SAWS |
CAN/CSA-E1029-1-94 (R2017) | Safety of Transportable Motor-Operated Electric Tools - Part 1: General Requirements (Adopted IEC 1029-1:1990, first edition, with Canadian deviations) | Sécurité des machines-outils électriques semi-fixes - Partie 1: Règles générales (norme CEI 1029-1:1990 adoptée, première édition, avec exigences propres au Canada) |
CSA/ANSI NGV 5.2-2017 | Vehicle fueling appliances (VFA) |
NFPA 52:2023 | Vehicular Natural Gas Fuel Systems Code |
CSA E1029.1 : 1994 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS |
CSA E1029.2.2 : 1994 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2: PARTICULAR REQUIREMENTS FOR RADIAL ARM SAWS |
CSA E1029.2.5 : 1994 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS |
CSA E1029.2.2 : 1994 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2: PARTICULAR REQUIREMENTS FOR RADIAL ARM SAWS |
CSA E1029.2.4 : 1994 : INC : AMD 1 : 2006 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-4: PARTICULAR REQUIREMENTS FOR BENCH GRINDERS |
CSA E1029.2.3 : 1994 : INC : AMD 1 : 2006 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-3: PARTICULAR REQUIREMENTS FOR PLANERS AND THICKNESSERS |
CSA Z241 SERIES : 2003 | PARK MODEL TRAILERS |
CSA E1029.2.6 : 1994 : R2013 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2: PARTICULAR REQUIREMENTS FOR DIAMOND DRILLS WITH WATER SUPPLY |
ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
ISO 19078:2013 | Gas cylinders — Inspection of the cylinder installation, and requalification of high pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
NFPA 58 : 2017 | LIQUEFIED PETROLEUM GAS CODE |
ASME B31.1 : 2016 | POWER PIPING |
Z7396.1-17 | Medical gas pipeline systems - Part 1: Pipelines for medical gases, medical vacuum, medical support gases, and anaesthetic gas scavenging systems |
ASTM D 1400 : 2000 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base (Withdrawn 2006) |
ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
CSA B108 : 2014 | COMPRESSED NATURAL GAS FUELLING STATIONS INSTALLATION CODE |
NACE TM 01 77 : 2016 | LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS |
ASME B31.3:2016 | PROCESS PIPING |
CAN/CSA-Z662-15 | Oil and gas pipeline systems |
ASTM D 2344/D2344M : 2016 : REDLINE | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
ASME B31.4 : 2016 | PIPELINE TRANSPORTATION SYSTEMS FOR LIQUIDS AND SLURRIES |
ASME PV CODE 4 : 2017 | BPVC Section IV-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF HEATING BOILERS |
CSA/ANSI PRD 1 : 2013(R2018) | PRESSURE RELIEF DEVICES FOR NATURAL GAS VEHICLE (NGV) FUEL CONTAINERS |
ANSI K61.1 : 1999 | SAFETY REQUIREMENTS FOR THE STORAGE AND HANDLING OF ANHYDROUS AMMONIA |
ISO 7866:2012 | Gas cylinders — Refillable seamless aluminium alloy gas cylinders — Design, construction and testing |
ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
CGA G 5.4 : 2012 | STANDARD FOR HYDROGEN PIPING SYSTEMS AT USER LOCATIONS |
ASME PVHO 1 : 2016 | SAFETY STANDARD FOR PRESSURE VESSELS FOR HUMAN OCCUPANCY |
ASME PV CODE 10 : 2017 | BOILER AND PRESSURE VESSEL CODE - FIBER-REINFORCED PLASTIC PRESSURE VESSELS |
ASTM G 154 : 2016 : REDLINE | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials |
MSS SP 25 : 2013 | STANDARD MARKING SYSTEM FOR VALVES, FITTINGS, FLANGES, AND UNIONS |
CSA Z180.1 : 2013 | COMPRESSED BREATHING AIR AND SYSTEMS |
ASME PV CODE 2D METRIC : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - PROPERTIES (METRIC) |
ASME B31.5 : 2016 | REFRIGERATION PIPING AND HEAT TRANSFER COMPONENTS |
BS EN 13322-2:2003 | Transportable gas cylinders. Refillable welded steel gas cylinders. Design and construction Stainless steel |
API 530 : 2015 | CALCULATION OF HEATER-TUBE THICKNESS IN PETROLEUM REFINERIES |
ASTM D 1186 : 2001 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base (Withdrawn 2006) |
ASME PV CODE 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF POWER BOILERS |
ISO 9001:2015 | Quality management systems — Requirements |
ISO 11114-4:2017 | Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 4: Test methods for selecting steels resistant to hydrogen embrittlement |
CSA Z299.4 : 1985 | QUALITY ASSURANCE PROGRAM - CATEGORY 4 |
ASTM D 2794 : 1993 | TEST METHOD FOR RESISTANCE OF ORGANIC COATINGS TO THE EFFECTS OF RAPID DEFORMATION (IMPACT) |
ASTM A 105/A105M : 2014-11 | SPECIFICATION FOR CARBON STEEL FORGINGS FOR PIPING APPLICATIONS |
CSA ISO 9001 : 2016 | QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS |
ASME PV CODE 2B : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - NONFERROUS MATERIAL SPECIFICATIONS |
ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
ASME PV CODE 5 : 2017 | BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION |
ASME B31.9 : 2014 | BUILDING SERVICES PIPING |
ASME PV CODE 2A : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - FERROUS MATERIAL SPECIFICATIONS (BEGINNING TO SA-450) AND (SA-451 TO END) |
CFR 49(PTS178-199) : OCT 2017 | TRANSPORTATION |
CSA Z299.2 : 1985 | QUALITY ASSURANCE PROGRAM - CATEGORY 2 |
ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
CGSB 48.9712 : 2014 | NON-DESTRUCTIVE TESTING - QUALIFICATION AND CERTIFICATION OF PERSONNEL |
ASME PV CODE 2D CUSTOMARY : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - PROPERTIES (CUSTOMARY) |
CSA B109 : 2017 | NATURAL GAS FOR VEHICLES INSTALLATION CODE |
ISO 9809-1:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa |
ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
ASME PV CODE SET : 2017 | BOILER AND PRESSURE VESSEL CODE - COMPLETE SET |
ASME PV CODE 2C : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS |
ASTM D 522 : 1993 : REV A | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
ASTM D 3359 : 2017 : REDLINE | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASME CSD1 : 2012 | CONTROLS AND SAFETY DEVICES FOR AUTOMATICALLY FIRED BOILERS |
CSA Z299.3 : 1985 | QUALITY ASSURANCE PROGRAM - CATEGORY 3 |
ISO 11439:2013 | Gas cylinders — High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
CSA Z299.1 : 1985 | QUALITY ASSURANCE PROGRAM - CATEGORY 1 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.