EN 13218:2002+A1:2008/AC:2010

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective
   measures
   5.1 General
   5.2 Mechanical hazards
   5.3 Electrical hazards
   5.4 Noise
   5.5 Vibration
   5.6 Hazards resulting from dusts, fumes and mists
   5.7 Devices for the use of coolants
   5.8 Measures against fire and explosion hazards
   5.9 Lighting
   5.10 Control systems and control devices
   5.11 Electromagnetic compatibility
6 Verification of the safety requirements
   and/or measures
7 Information for use
   7.1 General
   7.2 Instruction handbook
   7.3 Marking
Annex A (normative) - Abrasive product guards, workzone
                      enclosures and their combinations on
                      stationary grinding machines
      A.1 Scope
      A.2 Terms and Symbols
      A.3 Safety requirements for abrasive
          product guards and workzone enclosures
          A.3.1 Shapes of abrasive product
                guards and angles of aperture
          A.3.2 Wall thicknesses and material
          A.3.3 Compound abrasive product
                guards
          A.3.4 Workzone enclosures
          A.3.5 Verification of strength, testing
          A.3.6 Attachment of transparent screens
                in workzone enclosures
          A.3.7 Screens for bench and pedestal
                grinding machines
      A.4 Criteria for the design of abrasive
          product guards and their means of
          attachment
          A.4.1 General
          A.4.2 Energy of abrasive product
                fragments
          A.4.3 Determination of the wall
                thicknesses of abrasive product
                guards
          A.4.4 Design of the means of attachment
Annex B (normative) - Clamping methods for abrasive
                      products and safety requirements
                      for tool holding devices
      B.1 Scope
      B.2 Clamping methods
      B.3 General requirements
      B.4 Design of flanges
          B.4.1 Clamping forces and tightening
                torques
          B.4.2 Outside clamping diameter,
                radial width and covering
          B.4.3 Stiffness
          B.4.4 Marking of flanges
      B.5 Devices for the mounting of
          abrasive products by means of
          clamping inserts
          B.5.1 Central threaded inserts
          B.5.2 Method for the determination
                of the run-out tolerance for collets
          B.5.3 Inserts for abrasive products
                type 2, 35, 36, 37
                and comparable abrasive products
Annex C (informative) - Calculation of the clamping
                        force and the tightening torque
                        for the mounting of abrasive
                        products by means of flanges
      C.1 Symbols
      C.2 Operating forces
      C.3 Necessary clamping force
      C.4 Tightening torque of the screws
      C.5 Surface pressure
Annex D (informative) - Noise reduction
      D.1 Measures for the reduction of
          noise emission
Annex E (normative) - Noise emission determination,
                      declaration and verification
      E.1 Measuring procedure
      E.2 Operating conditions
      E.3 Declaration and verification of noise
          emission values
Annex F (normative) - Requirements for grinding
                      machines for the machining of
                      materials generating flammable
                      and explosive dusts
      F.1 Devices for wet grinding
      F.2 Devices for dry grinding with
          wet precipitation by means of
          instantaneous moistening
      F.3 Devices for dry grinding with
          precipitation by means of a
          wet-type cyclone
      F.4 Additional requirements, dry grinding
Annex G (informative) - Relevant and special clauses
                        for different types of stationary
                        grinding machines
Annex ZA (informative) - Relationship between this
                         European Standard and the
                         Essential Requirements of EU
                         Directives 98/37/EC amended
                         by Directive 98/79/EC, 89/336/EEC
                         and 73/23/EEC
Annex ZB (informative) - Relationship between this
                         European Standard and the
                         Essential Requirements of EU
                         Directive 2006/42/EC
Bibliography

Describes the technical safety requirements and/or protective measures to be adopted by persons undertaking the design, construction and supply (including installation and dismantling, arrangements for transport and maintenance) of stationary grinding machines.