• There are no items in your cart

EN 1889-1:2011

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Machines for underground mines - Mobile machines working underground - Safety - Part 1: Rubber tyred vehicles

Superseded date

30-06-2019

Published date

20-07-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or safety measures
6 Verification of safety requirements
7 Information for use
Annex A (normative) - Brake testing
Annex B (normative) - Verification data for safety requirements
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 2006/42/EC
Bibliography

1.1This European Standard specifies the safety requirements and tests for self-propelled rubber tyred vehicles as defined in 3.1 intended primarily for use in underground mining (i.e. as mine vehicles) and other underground workings (e.g. as tunnelling vehicles). The electrical supply voltage is limited to 1100 A.C. and 1500 D.C.1.2This European Standard deals with all significant hazards, hazardous situations and hazardous events, applying to self-propelled, rubber-tyred vehicles, subject to being used according to their intended purpose and prevailing manufacturer’s conditions and within the scope of foreseeable misuse. This European Standard describes appropriate action to be taken to avoid or minimize the risk of significant hazards.1.3This European Standard does not include rubber tyred drilling rigs, which are covered by EN 791, or earth-moving machinery not intended primarily for use in underground mines, which are covered by EN 474 (all parts). This European Standard does not take account of specific hazards associated with special-purpose vehicles, e.g. tankers, explosives vehicles.This standard does not cover the use and operation of rubber-tyred vehicles being remotely controlled or operation in potentially explosive atmospheres.1.4This European Standard applies to vehicles which are manufactured after the date of issue of this standard.1.5This European standard does not consider the use of vehicles in explosive atmosphere.

Committee
CEN/TC 196
DevelopmentNote
Supersedes PREN 1889-1. (02/2012)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NBN EN 1889-1 : 2011 Identical
I.S. EN 1889-1:2011 Identical
NS EN 1889-1 : 2011 Identical
UNE-EN 1889-1:2012 Identical
NEN EN 1889-1 : 2011 Identical
BS EN 1889-1:2011 Identical
SN EN 1889-1 : 2011 Identical
DIN EN 1889-1 E : 2011 Identical
UNI EN 1889-1 : 2011 Identical
NF EN 1889-1 : 2011 Identical
PN EN 1889-1 : 2011 Identical
DIN EN 1889-1:2011-10 Identical

09/30161046 DC : 0 BS ISO 3450 - EARTH-MOVING MACHINERY - RUBBER-TYRED/TRACKED MACHINES - PERFORMANCE REQUIREMENTS AND TEST PROCEDURES FOR BRAKE SYSTEMS
BS EN ISO 3450:2011 Earth-moving machinery. Wheeled or high-speed rubber-tracked machines. Performance requirements and test procedures for brake systems
I.S. EN ISO 3450:2011 EARTH-MOVING MACHINERY - WHEELED OR HIGH-SPEED RUBBERTRACKED MACHINES - PERFORMANCE REQUIREMENTS AND TEST PROCEDURES FOR BRAKE SYSTEMS (ISO 3450:2011)
UNI EN ISO 3450 : 2012 EARTH-MOVING MACHINERY - WHEELED OR HIGH-SPEED RUBBER-TRACKED MACHINES - PERFORMANCE REQUIREMENTS AND TEST PROCEDURES FOR BRAKE SYSTEMS
UNI EN 1710 : 2008 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
PREN ISO 3450 : DRAFT 2009 EARTH-MOVING MACHINERY - WHEELED OR HIGH-SPEED RUBBERTRACKED MACHINES - PERFORMANCE REQUIREMENTS AND TEST PROCEDURES FOR BRAKE SYSTEMS
DIN EN 1710:2008-08 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
UNE-EN ISO 3450:2012 Earth-moving machinery - Wheeled or high-speed rubber-tracked machines - Performance requirements and test procedures for brake systems (ISO 3450:2011)
BS EN 1710 : 2005 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
ISO 3450:2011 Earth-moving machinery — Wheeled or high-speed rubber-tracked machines — Performance requirements and test procedures for brake systems
EN 1710:2005+A1:2008/AC:2010 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
EN ISO 3450:2011 Earth-moving machinery - Wheeled or high-speed rubber-tracked machines - Performance requirements and test procedures for brake systems (ISO 3450:2011)
15/30302205 DC : DRAFT FEB 2015 BS EN ISO 19296 - MINING AND EARTHMOVING MACHINERY - MOBILE MACHINES WORKING UNDERGROUND - MACHINE SAFETY
DIN EN ISO 3450:2012-04 Earth-moving machinery - Wheeled or high-speed rubber-tracked machines - Performance requirements and test procedures for brake systems (ISO 3450:2011)

ISO 3449:2005 Earth-moving machinery — Falling-object protective structures — Laboratory tests and performance requirements
EN 12096:1997 Mechanical vibration - Declaration and verification of vibration emission values
EN ISO 2860:2008 Earth-moving machinery - Minimum access dimensions (ISO 2860:1992)
EN 12254:2010/AC:2011 SCREENS FOR LASER WORKING PLACES - SAFETY REQUIREMENTS AND TESTING
ISO 8030:2014 Rubber and plastics hoses — Method of test for flammability
EN 60825-4:2006/A2:2011 SAFETY OF LASER PRODUCTS - PART 4: LASER GUARDS
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 547-2:1996+A1:2008 Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings
EN ISO 6683:2008 Earth-moving machinery - Seat belts and seat belt anchorages - Performance requirements and tests (ISO 6683:2005)
ISO 10570:2004 Earth-moving machinery — Articulated frame lock — Performance requirements
ISO 13333:1994 Earth-moving machinery Dumper body support and operator's cab tilt support devices
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
ISO 7096:2000 Earth-moving machinery Laboratory evaluation of operator seat vibration
ISO 3411:2007 Earth-moving machinery Physical dimensions of operators and minimum operator space envelope
ISO 6683:2005 Earth-moving machinery Seat belts and seat belt anchorages Performance requirements and tests
EN ISO 3449:2008 Earth-moving machinery - Falling-object protective structures - Laboratory tests and performance requirements (ISO 3449:2005)
EN ISO 3411:2007 Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007)
ISO 6405-2:2017 Earth-moving machinery Symbols for operator controls and other displays Part 2: Symbols for specific machines, equipment and accessories
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
EN 60332-2-2:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame
ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
ISO 12508:1994 Earth-moving machinery Operator station and maintenance areas Bluntness of edges
EN 1679-1:1998+A1:2011 Reciprocating internal combustion engines - Safety - Part 1: Compression ignition engines
EN 1837:1999+A1:2009 Safety of machinery - Integral lighting of machines
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
IEC 60825-4:2006+AMD1:2008+AMD2:2011 CSV Safety of laser products - Part 4: Laser guards
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN 547-1:1996+A1:2008 Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery
IEC 60332-2-2:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame
ISO 5010:2007 Earth-moving machinery Rubber-tyred machines Steering requirements
ISO 6396:2008 Earth-moving machinery Determination of emission sound pressure level at operator's position Dynamic test conditions
EN ISO 7731:2008 Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
ISO 12509:2004 Earth-moving machinery — Lighting, signalling and marking lights, and reflex-reflector devices
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
EN 60332-1-2:2004/A11:2016 TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015)
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 7731:2003 Ergonomics Danger signals for public and work areas Auditory danger signals
IEC 60332-1-1:2004+AMD1:2015 CSV Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulatedwire or cable - Apparatus
ISO 6393:2008 Earth-moving machinery Determination of sound power level Stationary test conditions
EN 791:1995+A1:2009 Drill rigs - Safety
IEC 60332-1-2:2004+AMD1:2015 CSV Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
ISO 9244:2008 Earth-moving machinery Machine safety labels General principles
EN ISO 3450:2011 Earth-moving machinery - Wheeled or high-speed rubber-tracked machines - Performance requirements and test procedures for brake systems (ISO 3450:2011)
ISO 3471:2008 Earth-moving machinery — Roll-over protective structures — Laboratory tests and performance requirements
EN ISO 8030:2014 Rubber and plastics hoses - Method of test for flammability (ISO 8030:2014)
ISO 1813:2014 Belt drives — V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts — Electrical conductivity of antistatic belts: Characteristics and methods of test
EN 60332-1-1:2004/A1:2015 Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulated wire or cable - Apparatus
ISO 2860:1992 Earth-moving machinery — Minimum access dimensions
ISO 5006:2017 Earth-moving machinery — Operator's field of view — Test method and performance criteria
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN 13309:2010 Construction machinery - Electromagnetic compatibility of machines with internal power supply
EN ISO 4414:2010 Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010)
EN 547-3:1996+A1:2008 Safety of machinery - Human body measurements - Part 3: Anthropometric data
ISO 6405-1:2017 Earth-moving machinery Symbols for operator controls and other displays Part 1: Common symbols
EN ISO 3471:2008 Earth-moving machinery - Roll-over protective structures - Laboratory tests and performance requirements (ISO 3471:2008)
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 6682:2008 Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989)
IEC 60332-2-1:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable - Apparatus
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
ISO 3864-1:2011 Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings
ISO 6395:2008 Earth-moving machinery Determination of sound power level Dynamic test conditions
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 4414:2010 Pneumatic fluid power General rules and safety requirements for systems and their components
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 60332-2-1:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable - Apparatus
EN ISO 2867:2011 Earth-moving machinery - Access systems (ISO 2867:2011)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 10533:1993 Earth-moving machinery — Lift-arm support devices
EN ISO 4413:2010 Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 2867:2011 Earth-moving machinery Access systems
ISO 9533:2010 Earth-moving machinery Machine-mounted audible travel alarms and forward horns Test methods and performance criteria
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
ISO 3450:2011 Earth-moving machinery — Wheeled or high-speed rubber-tracked machines — Performance requirements and test procedures for brake systems
ISO 6805:1994 Rubber hoses and hose assemblies for underground mining Wire-reinforced hydraulic types for coal mining Specification
ISO 7745:2010 Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use
ISO 3864-4:2011 Graphical symbols Safety colours and safety signs Part 4: Colorimetric and photometric properties of safety sign materials
EN ISO 7096:2008/AC:2009 EARTH-MOVING MACHINERY - LABORATORY EVALUATION OF OPERATOR SEAT VIBRATION
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.