EN 62246-1:2015
Current
The latest, up-to-date edition.
Reed switches - Part 1: Generic specification
20-03-2015
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Rated values
5 Marking
6 Test and measurement procedures
Annex A (normative) - Standard test coils for reed switches
Annex B (normative) - Test systems
Annex C (informative) - Electrical endurance test circuit
Annex D (informative) - Inrush current loads
Annex E (informative) - Conditional short-circuit current test circuit
Annex F (informative) - Electrical ratings based on classification
Annex G (informative) - Example of horsepower ratings
Annex H (informative) - Example of test arrangement for
contact reliability test
Annex I (informative) - Example of test arrangement for making
current capacity test
Annex J (informative) - Example of test arrangement for breaking
current capacity test
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding
European publications
IEC 62246-1:2015, which is a generic specification, applies to all types of reed switches including magnetically biased reed switches of assessed quality for use in general and industrial applications. Mercury wetted reed switches are not covered by this standard due to their possible environmental impact. It lists the tests and measurement procedures which may be selected for use in detail specifications for such reed switches. This standard applies to reed switches which are operated by an applied magnetic field; it is not restricted to any particular type of contact load. For elementary relays with reed switches, this standard is recommended to be used together with the standards IEC 61810-1, IEC 61811-1 as applicable.For applications of reed switches, this standard is recommended to be used together with specific product standards. This standard cancels and replaces the second edition of IEC 62246-1 published in 2011. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:- inclusion of Introduction;- update of the scope, the terms and definitions, the rated values and the test and measurement procedure;- improvement of dielectric test, electrical endurance tests covering maximum electrical endurance test and overload test;- improvement of Table F.1 for electrical ratings based on classification;- inclusion of new Table G.1 for horsepower ratings based on classification.
Committee |
CLC/SR 94
|
DevelopmentNote |
Supersedes EN 119000. (09/2002) Supersedes EN 62246-2. (04/2011)
|
DocumentType |
Standard
|
PublisherName |
European Committee for Standards - Electrical
|
Status |
Current
|
Supersedes |
Standards | Relationship |
NF EN 62246-1 : 2015 | Identical |
IEC 62246-1:2015 | Identical |
I.S. EN 62246-1:2015 | Identical |
PN EN 62246-1 : 2015 | Identical |
BS EN 62246-1:2015 | Identical |
DIN EN 62246-1 : 2015 | Identical |
CEI EN 62246-1 : 2015 | Identical |
NBN EN 62246-1 : 2015 | Identical |
VDE 0435-205 : 2015 | Identical |
NEN EN IEC 62246-1 : 2015 | Identical |
SN EN 62246-1:2015 | Identical |
PNE-FprEN 62246-1 | Identical |
UNE-EN 62246-1:2015 | Identical |
BS EN 62246-2:2008 | Reed contact units Heavy-duty reed switches |
I.S. EN 62246-1-1:2013 | REED SWITCHES - PART 1-1: GENERIC SPECIFICATION - QUALITY ASSESSMENT (IEC 62246-1-1:2013 (EQV)) |
I.S. EN 62246-2:2008 | REED CONTACT UNITS - PART 2: HEAVY-DUTY REED SWITCHES |
EN 62246-2:2008 | Reed contact units - Part 2: Heavy-duty reed switches |
BS EN IEC 62246-1-1:2018 | Reed switches Generic specification. Blank detail specification |
BS EN 62246-1-1:2013 | Reed switches Generic specification. Quality assessment |
EN IEC 62246-1-1:2018 | Reed switches - Part 1-1: Generic specification - Blank detail specification |
I.S. EN IEC 62246-1-1:2018 | REED SWITCHES - PART 1-1: GENERIC SPECIFICATION - BLANK DETAIL SPECIFICATION |
CEI EN 62246-1-1 : 2014 | REED SWITCHES - PART 1-1: GENERIC SPECIFICATION - QUALITY ASSESSMENT |
17/30356728 DC : 0 | BS EN 12261 - GAS METERS - TURBINE GAS METERS |
PREN 12261 : DRAFT 2017 | GAS METERS - TURBINE GAS METERS |
EN 62246-1-1:2013 | Reed switches - Part 1-1: Generic specification - Quality assessment |
IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
EN 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
IEC 61810-1:2015 | Electromechanical elementary relays - Part 1: General and safety requirements |
EN 60068-2-7:1993 | Environmental testing - Part 2: Tests - Test Ga: Acceleration, steady state |
IEC 61810-2:2017 | Electromechanical elementary relays - Part 2: Reliability |
EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
EN 60068-2-17:1994 | Environmental testing - Part 2: Tests - Test Q: Sealing |
IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
EN 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
IEC 60317-1:2010 | Specifications for particular types of winding wires - Part 1: Polyvinyl acetal enamelled round copper wire, class 105 |
EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
EN 60068-2-13:1999 | Environmental testing - Part 2: Tests - Test M: Low air pressure |
EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
IEC 61811-1:2015 | Electromechanical telecom elementary relays of assessed quality - Part 1: Generic specification and blank detail specification |
IEC 60050-444:2002 | International Electrotechnical Vocabulary (IEV) - Part 444: Elementary relays |
EN 60068-2-11:1999 | Environmental testing - Part 2: Tests - Test Ka: Salt mist |
IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.