EN 777-4:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use - Part 4: System H - Safety
23-03-2022
11-03-2009
Foreword
1 Scope
2 Normative references
3 Terms and definitions
3.1 System and its constituent parts
3.2 Combustion circuit
3.3 Adjusting, control and safety devices
3.4 System operation
3.5 Gases
3.6 Conditions of operation and measurement
3.7 Country of destination
4 Classification of systems
4.1 Classification according to the nature of the
gases used (categories)
4.2 Classification according to the gases
capable of being used
4.3 Classification according to the mode of evacuation
of the combustion products
5 Constructional requirements
5.1 General
5.2 Requirements for adjusting, control and safety
devices
5.3 Ignition devices
5.4 Main burners
5.5 Pressure test points
5.6 Injectors
6 Operational requirements
6.1 Soundness
6.2 Heat inputs
6.3 Limiting temperatures
6.4 Ignition, cross-lighting and flame stability
6.5 Pressure regulator
6.6 Combustion
6.7 Prolonged performance
6.8 Measurements of oxides of Nitrogen, NO[X]
7 Test methods
7.1 General
7.2 Construction and design
7.3 Safety of operation
7.4 Other pollutants
8 Marking and instructions
8.1 Marking of the system and the packaging
8.2 Instructions
8.3 Presentation
9 Evaluation of conformity of POCEDs and their
associated terminals
9.1 General
9.2 Type testing
9.3 Factory production control (FPC)
Annex A (informative) - National situations
A.1 General
A.2 Categories listed in the body of the
standard and marketed in different
countries
A.3 Appliance supply pressures corresponding
to the categories given in A.2
A.4 Special categories marketed nationally or
locally
A.5 Test gases corresponding to the special
categories given in A.4
A.6 Gas connections in the various countries
A.7 Flue connections in the various countries
Annex B (informative) - System H
Annex C (informative) - Equivalence rules
C.1 Conversion to categories within a restricted
Wobbe Index range
C.2 Conversion to categories within an identical
Wobbe Index range
C.3 Conversion to categories within a wider
Wobbe Index range
Annex D (informative) - Calculation of the mass flow rate
of flue gases
D.1 Flue gas mass flow rate
D.2 Quantity of air in the flue gas
D.3 Flue gas excess air ratio (lambda)
D.4 Quantity of water vapour in the flue gas
D.5 Quantity of Nitrogen in the flue gas
D.6 Quantity of Oxygen in the flue gas
D.7 Dry quantity of flue gas
D.8 Quantity of carbon dioxide in the flue gas
Annex E (informative) - Identification of gas types in use
in various countries
Annex F (normative) - Special national conditions
F.1 General
Annex G (informative) - Example of calculation of the
weighting factors for a system with several rates
G.1 Appliance rates
G.2 Weighting of Q[pi],% = 20
G.3 Weighting of Q[pi],% = 40
G.4 Weighting of Q[pi],% = 60
G.5 Weighting of Q[pi],% = 70
G.6 Total weighting
Annex H (informative) - Calculation of conversions
of NO[X]
H.1 NO[X] emission conversion factors
H.2 NO[X] Conversion - Calculation
Annex I (informative) - National situations of countries
whose national bodies are CEN associate
members
Annex J (informative) - An example of sampling plans
J.1 Sampling plans
J.2 Inspection levels and procedures
Annex K (informative) - Flue determination
K.1 General conditions of test
K.2 Test conditions
K.3 Test procedure
K.4 Accuracy of measurement
K.5 Calculation of Flue Loss
Annex ZA (informative) - Clauses of this European
Standard addressing essential requirements or
other provisions of EU Directives
Annex ZB (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Directive
ZB.1 Scope and relevant characteristics
ZB.2 Procedure(s) for attestation of conformity of
[construction products]
ZB.3 CE marking and labelling
Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.