![header thumbnail](/images/img-default-logo.png)
EN 81-43:2009
Current
The latest, up-to-date edition.
![header thumbnail](/images/img-default-logo.png)
Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes
13-05-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
5.1 General
5.2 Load combinations and calculations
5.3 Base frame
5.4 Mast, ties and buffers
5.5 Liftway protection and landing access
5.6 Car
5.7 Drive unit
5.8 Electric installations and appliances
5.9 Control and limiting devices
5.10 Breakdown conditions
6 Verification
6.1 Verification of design
6.2 Special verification tests
6.3 Verification tests on each lift before first use
7 User information
7.1 Instruction handbook
7.2 Markings
7.3 Marking of control elements
Annex A (normative) - European stormwind map
Annex B (normative) - Electric safety devices
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
1.1This document specifies the safety requirements for the construction and installation of power operated lifts attached to cranes and intended for access to workplaces on cranes, by authorised persons. This includes intended use, erection, dismantling, inspection and maintenance. The lift serves defined landing levels and has a load carrying unit which is:-designed for the transportation of persons and goods;-guided;-travelling vertically or along a path within 15 degrees maximum from the vertical;-supported by rack and pinion or suspended by steel wire ropes;-travelling with a speed not more than 1,0 m/s for permanent lifts and not more than 0,4 m/s for temporary lifts.1.2This document identifies hazards as listed in Clause 4 which arise during the various phases in the life of such equipment and describes methods for the elimination or reduction of these hazards when used as intended by the manufacturer.1.3This document does not specify the additional requirements for:-operation in severe conditions (e.g. extreme climates, strong magnetic fields);--lightning protection;-operation subject to special rules (e.g. potentially explosive atmospheres);NOTEDirective 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.-electromagnetic compatibility (emission, immunity);-handling of loads the nature of which could lead to dangerous situations;-the use of combustion engines;-hydraulic drive units;-hazards occurring during manufacturing process;-hazards occurring as a result of being erected over a public road;-earthquakes;-noise (see also Directive on noise emissions from machines used outdoors (2000/14/EC)).
Committee |
CEN/TC 10
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
I.S. EN 81-43:2009 | Identical |
DIN EN 81-43:2010-05 | Identical |
NF EN 81-43 : 2009 | Identical |
NEN EN 81-43 : 2009 | Identical |
PN EN 81-43 : 2009 | Identical |
SN EN 81-43 : 2009 | Identical |
BS EN 81-43:2009 | Identical |
UNE-EN 81-43:2010 | Identical |
NS EN 81-43 : 2009 | Identical |
UNI EN 81-43 : 2009 | Identical |
NBN EN 81-43 : 2009 | Identical |
UNE-EN 12159:2013 | Builders hoists for persons and materials with vertically guided cages |
BS EN 12159:2012 | Builders hoists for persons and materials with vertically guided cages |
14/30285286 DC : 0 | BS EN 14439 - CRANES - SAFETY - TOWER CRANES |
DIN EN 12159:2013-03 | BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES |
DIN EN 15011:2014-09 | Cranes - Bridge and gantry cranes (includes Amendment A1:2014) |
EN 15011:2011+A1:2014 | Cranes - Bridge and gantry cranes |
I.S. EN 12159:2012 | BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES |
UNI EN 12159 : 2013 | BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES |
I.S. EN 15011:2011 | CRANES - BRIDGE AND GANTRY CRANES |
17/30357380 DC : 0 | BS EN 15011 - CRANES - BRIDGE AND GANTRY CRANES |
BS EN 15011 : 2011 | CRANES - BRIDGE AND GANTRY CRANES |
10/30218104 DC : 0 | BS EN 15011 - CRANES - BRIDGE & GANTRY CRANES |
EN 12159:2012 | Builders hoists for persons and materials with vertically guided cages |
PREN 14439 : DRAFT 2014 | CRANES - SAFETY - TOWER CRANES |
UNI EN 15011 : 2014 | CRANES - BRIDGE AND GANTRY CRANES |
UNE-EN 15011:2011 | Cranes - Bridge and gantry cranes |
CEN/TS 13001-3-1:2004/AC:2006 | CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES |
EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) |
EN 14502-2:2005+A1:2008 | Cranes - Equipment for the lifting of persons - Part 2: Elevating control stations |
EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
EN 1999-1-1:2007/A2:2013 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES |
IEC 60947-5-1 : 4.0 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES |
ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength |
IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
EN 12158-1:2000+A1:2010 | Builders' hoists for goods - Part 1: Hoists with accessible platforms |
EN 13586:2004+A1:2008 | Cranes - Access |
EN 81-1:1998+A3:2009 | Safety rules for the construction and installation of lifts - Part 1: Electric lifts |
EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
EN 12158-2:2000+A1:2010 | Builders' hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices |
ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials |
EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
EN ISO 12100-1:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
ISO 4309:2010 | Cranes Wire ropes Care and maintenance, inspection and discard |
EN 60947-4-1 : 2010 AMD 1 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012) |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
EN 12159:2012 | Builders hoists for persons and materials with vertically guided cages |
ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
EN ISO 12100-2:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors |
ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
EN 1808:2015 | Safety requirements for suspended access equipment - Design calculations, stability criteria, construction - Examinations and tests |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
EN 13015:2001+A1:2008 | Maintenance for lifts and escalators - Rules for maintenance instructions |
EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.