Quality Management Systems - Requirements for Aviation, Space and Defense Organizations

Superseded date

09-08-2019

Superseded by

EN 9100:2018

Published date

12-08-2009

Publisher

Comite Europeen de Normalisation

Sorry this product is not available in your region.

Foreword
0 INTRODUCTION
QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS
1 SCOPE
2 NORMATIVE REFERENCES
3 TERMS AND DEFINITIONS
4 QUALITY MANAGEMENT SYSTEM
5 MANAGEMENT RESPONSIBILITY
6 RESOURCE MANAGEMENT
7 PRODUCT REALIZATION
8 MEASUREMENT, ANALYSIS AND IMPROVEMENT
BIBLIOGRAPHY

additional aviation, space and defense industry requirements, definitions and notes as shown in bold,italic text.It is emphasized that the requirements specified in this standard are complementary (not alternative)to contractual and applicable statutory and regulatory requirements. Should there be a conflictbetween the requirements of this standard and applicable statutory or regulatory requirements, thelatter shall take precedence.This International Standard specifies requirements for a quality management system where an organizationa) needs to demonstrate its ability to consistently provide product that meets customer and applicablestatutory and regulatory requirements, andb) aims to enhance customer satisfaction through the effective application of the system, includingprocesses for continual improvement of the system and the assurance of conformity to customer andapplicable statutory and regulatory requirements.NOTE 1 In this International Standard, the term “product” only applies toa) product intended for, or required by, a customer,b) any intended output resulting from the product realization processes.NOTE 2 Statutory and regulatory requirements can be expressed as legal requirements.1.2 ApplicationAll requirements of this International Standard are generic and are intended to be applicable to allorganizations, regardless of type, size and product provided.Where any requirement(s) of this International Standard cannot be applied due to the nature of anorganization and its product, this can be considered for exclusion.Where exclusions are made, claims of conformity to this International Standard are not acceptable unlessthese exclusions are limited to requirements within Clause 7, and such exclusions do not affect theorganization's ability, or responsibility, to provide product that meets customer and applicable statutory andregulatory requirements.

Committee	ASD-STAN
DevelopmentNote	Supersedes PREN 2000. (11/2003)
DocumentType	Standard
PublisherName	Comite Europeen de Normalisation
Status	Superseded
SupersededBy	EN 9100:2018
Supersedes	EN 9100:2003 EN 2000:1991 PREN 2000 : 3

Standards	Relationship
DIN EN 9100:2018-08	Identical
I.S. EN 9100:2009	Identical
I.S. EN 9100:2018	Identical
DIN EN 9100:2010-07	Identical
NEN EN 9100 : 2009	Identical
UNI EN 9100 : 2009	Identical
NF EN 9100 : 2010	Identical
SN EN 9100 : 2018	Identical
BS EN 9100:2009	Identical
NS EN 9100 : 2009	Identical
UNE-EN 9100:2018	Identical
UNE-EN 9100:2010	Identical
NF EN 9100 : 2018	Identical
BS EN 9100:2018	Identical
DIN EN 9100:2018	Identical
SN EN 9100 : 2010	Identical
NS EN 9100:2018	Identical
PN EN 9100 : 2009	Identical
NBN EN 9100 : 2009	Identical
GOST R EN 9100 : 2011	Identical

XP PREN 9134 : 2005 XP	AEROSPACE SERIES - QUALITY SYSTEMS - SUPPLY CHAIN RISK MANAGEMENT GUIDELINE
BS EN 3228:2010	Aerospace series. Nuts, hexagonal, plain, reduced height, normal across flats, in steel, cadmium plated. Classification: 900 MPa (at ambient temperature)/235°C
BS EN 4803:2017	Aerospace series. Flange couplings. Swivel flange with 4 fastening holes, in heat resisting steel. Inch series
BS EN 4817:2012	Aerospace series. Passive UHF RFID tags intended for aircraft use
I.S. EN 4702-03:2017	AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
I.S. EN 4084:2009	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, WITH COUNTERBORE, IN ALLOY STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
I.S. EN 2852:2010	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, HEAT RESISTING STEEL PASSIVATED - CLASSIFICATION: 1100 MPA/650 DEGREES C
BS EN 3435:2010	Aerospace series. Nuts, anchor, self-locking, floating, two lug, reduced series, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
11/30250205 DC : 0	BS EN 6138 - AEROSPACE SERIES - CAP, PROTECTIVE, NON METALLIC FOR FITTING ENDS <= 3000 PSI HYDRAULIC SYSTEMS
14/30301106 DC : 0	BS EN 4575 - AEROSPACE SERIES - TRIVALENT CHROMIUM BASED CHEMICAL CONVERSION COATINGS FOR ALUMINIUM AND ALUMINIUM ALLOYS
BS EN 4812:2017	Aerospace series. Flange couplings. Gasket seal with nickel alloy C seal on heat resisting steel plate with 4 fastening holes. Inch series
BS EN 3875:2017	Aerospace series. Metallic materials, Filler metal for brazing. Technical specification
I.S. EN 2869:2009	AEROSPACE SERIES - NUTS, HEXAGONAL, SLOTTED/CASTELLATED, NORMAL HEIGHT, NORMAL ACROSS FLATS, IN HEAT RESISTING STEEL, PASSIVATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C
I.S. EN 3227:2010	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, IN STEEL, CADMIUM PLATED, LEFT HAND THREAD - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
BS ISO 10327:2014	Air cargo. Main deck containers. Design and testing
16/30354034 DC : 0	BS EN 4854-1 - AEROSPACE SERIES - BEARINGS, SPHERICAL PLAIN, IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER, LOW STARTING TORQUE AND LOW FRICTION COEFFICIENT, ELEVATED DUTY CYCLES UNDER LOW OSCILLATIONS AT DIFFERENT OPERATING CONDITIONS, NARROW SERIES - DIMENSIONS AND LOADS
16/30342255 DC : 0	BS EN 8.3559 - AEROSPACE SERIES- SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, SPIRAL DRIVE RECESS, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 9116:2015	AEROSPACE SERIES - NOTICE OF CHANGE (NOC) REQUIREMENTS
10/30228108 DC : 0	BS EN 4400-9 - AEROSPACE SERIES - ALUMINIUM AND ALUMINIUM- AND MAGNESIUM- ALLOYS - TECHNICAL SPECIFICATION - PART 9: PRE-PRODUCTION AND PRODUCTION CASTINGS
13/30290101 DC : 0	BS EN 4700-2 - AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION
BS EN 2535:2011	Aerospace series. Vacuum deposition of cadmium
BS EN 3537:2010	Aerospace series. Nuts, anchor, self-locking, fixed, two lug, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
BS EN 4807:2017	Aerospace series. Flange couplings. Weld coupling, 90° elbow, in heat resisting steel. Inch series
17/30369678 DC : 0	PREN 7010 - AEROSPACE SERIES - USER GUIDE FOR CREATION AND DESIGNATION OF BOLTS
BS EN 3757:2009	Aerospace series. Nuts, anchor, self-locking, floating, self-aligning, two lugs, in heat resisting steel, MoS2 lubricated. Classification: 900 MPa (at ambient temperature)/315°C
17/30361847 DC : 0	BS EN 4161 - AEROSPACE SERIES - SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 4636:2009	Aerospace series. Screws, 100° countersunk head, six lobe recess, short thread, in titanium alloy TI-P64001, with aluminium pigmented coating. Classification: 1100 MPa (at ambient temperature) / 315°C
UNE-EN 9115:2013	Quality Management Systems - Requirements for Aviation, Space and Defense Organizations - Deliverable Software (Supplement to EN 9100)
BS EN 9104-003:2010	Aerospace series. Quality management systems Requirements for aerospace quality management system (AQMS) auditor training and qualification
BS EN 4178:2017	Aerospace series. Screws, pan head, six lobe recess, coarse tolerance normal shank, medium length thread, in titanium alloy, anodized, MoS2 lubricated. Classification: 1 100 MPa (at ambient temperature) / 315 °C
UNI EN 4700-006 : 2011	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS
BS EN 4297:2017	Aerospace series. Nuts, hexagon, self-locking by plastic ring, normal height, normal across flats, in corrosion resisting steel, passivated. Classification: 900 MPa (at ambient temperature) / 120 °C
BS EN 4138:2016	Aerospace series. Screws, pan head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1 100 MPa (at ambient temperature) / 235 °C
BS EN 4811:2017	Aerospace series. Flange couplings. Gasket seal with fluorocarbon seal on aluminium plate with 4 fastening holes. Inch series
13/30290552 DC : 0	BS EN 4691-1 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
BS ISO 7169:2014	Aerospace. Separable tube fittings for fluid systems, for 24° cones, for pressures up to 3 000 psi or 21 000 kPa. Procurement specification, inch/metric
BS EN 4702-05:2017	Aerospace series. Quick release fastening systems for non-structural and lining applications Retaining washer
15/30322448 DC : 0	BS EN 9223-101 - PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 101: CONFIGURATION IDENTIFICATION
BS EN 4697:2016	Aerospace series. General and installation requirements for passenger seat fittings
I.S. EN 4700-002:2016	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION
BS EN 4707:2014	Aerospace series. Acid pickling of aluminum and aluminum alloy without hexavalent chromium
17/30364784 DC : 0	BS EN 4707 - AEROSPACE SERIES - ACID PICKLING OF ALUMINUM AND ALUMINUM ALLOY WITHOUT HEXAVALENT CHROMIUM
NF EN 3538 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
NF EN 3750 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 90 DEGREES CORNER, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
NF EN 3653 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, SELF-ALIGNING, ONE LUG, IN STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS ISO 8913:2006	Aerospace. Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 400°F/3000 psi (204°C/20684 kPa) and 204°C/21000 kPa (400°F/3046 psi). Procurement specification
BS EN 4700-005:2010	Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Forging stock
16/30342253 DC : 0	BS EN 8.3557 - AEROSPACE SERIES- SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, SPIRAL DRIVE RECESS, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
BS EN 4810:2017	Aerospace series. Flange couplings. Gasket seal with nickel alloy C seal on heat resisting steel plate with 3 fastening holes. Inch series
BS ISO 12319:2006	Aerospace. \'P\' (loop style) clamps. Procurement specification
06/30152010 DC : 0	EN 2755 - BEARING SPHERICAL JOINTS C/R STEEL, SELF-LUB LINER - EL. LOAD
BS EN 16602-20:2014	Space product assurance. Quality assurance
XP PREN 9103 : 2003 XP	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - VARIATION MANAGEMENT OF KEY CHARACTERISTICS
SAE AS 5553B : 2016	COUNTERFEIT ELECTRICAL, ELECTRONIC, AND ELECTROMECHANICAL (EEE) PARTS; AVOIDANCE, DETECTION, MITIGATION, AND DISPOSITION
15/30322451 DC : 0	BS EN 9223-102 - PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 102: CONFIGURATION STATUS ACCOUNTING
09/30205276 DC : 0	BS EN 2311 - AEROSPACE SERIES - BUSHES WITH SELF-LUBRICATING LINER - TECHNICAL SPECIFICATION
PREN 9101 : 200P7	QUALITY MANAGEMENT SYSTEMS - AUDIT REQUIREMENTS FOR AVIATION, SPACE, AND DEFENSE ORGANIZATIONS
UNI EN 4800-006 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS
PREN 9135 : DRAFT 2003	AEROSPACE SERIES - QUALITY SYSTEMS - SPECIFIC QUALITY REQUIREMENTS FOR NATO SUPPLIERS
UNE-EN 9102:2016	Aerospace series - Quality systems - First article inspection requirements
I.S. EN 4499:2009	AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK REDUCED HEAD, OFFSET CRUCIFORM RECESS, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ANODIZED, WITH ALUMINIUM PIGMENTED COATING - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
PREN 4803 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 4 FASTENING HOLES, IN HEAT RESISTING STEEL - INCH SERIES
PREN 4811 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH FLUOROCARBON SEAL ON ALUMINIUM PLATE WITH 4 FASTENING HOLES - INCH SERIES
I.S. EN 16602-20-07:2016	SPACE PRODUCT ASSURANCE - QUALITY AND SAFETY ASSURANCE FOR SPACE TEST CENTRES
PREN 2133 : 200P1	AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS
UNI EN 3539 : 2011	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, ONE LUG, FIXED, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 2535:2011	AEROSPACE SERIES - VACUUM DEPOSITION OF CADMIUM
PREN 3302 : 200P2	AEROSPACE SERIES - BOLTS IN HEAT RESISTING STEEL FE-PM1708 (FV535) - CLASSIFICATION: 1000 MPA/550 DEGREES C - TECHNICAL SPECIFICATION
PREN 2755 : 200P3	AEROSPACE SERIES - BEARINGS, SPHERICAL PLAIN IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER - ELEVATED LOAD AT AMBIENT TEMPERATURE - TECHNICAL SPECIFICATION
I.S. EN 4702-05:2017	AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 05: RETAINING WASHER
PREN 2311 : 200P2	AEROSPACE SERIES - BUSHES WITH SELF-LUBRICATING LINER - TECHNICAL SPECIFICATION
I.S. EN 3843:2010	AEROSPACE SERIES - NUTS, BIHEXAGONAL, SELF-LOCKING, WITH COUNTERBORE, IN HEAT RESISTING STEEL, PASSIVATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C
UNE-EN 9104-002:2017	Aerospace series - Quality management systems - Part 002: Requirements for Oversight of Aerospace Quality Management System Registration/Certification Programs
TR 4858 : 2018	AEROSPACE SERIES - PIPE COUPLINGS MATERIALS AND SURFACE TREATMENTS
PREN 4813 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - CAP, IN HEAT RESISTING STEEL - INCH SERIES
PREN 4804 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 4 FASTENING HOLES, IN NICKEL ALLOY - INCH SERIES
PREN 4810 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH NICKEL ALLOY C SEAL ON HEAT RESISTING STEEL PLATE WITH 3 FASTENING HOLES - INCH SERIES
PREN 4700-005 : 200P2	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK
PREN 4800-006 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 6: PRE-PRODUCTION AND PRODUCTION FORGINGS
PREN 9137 : 200P1	QUALITY MANAGEMENT SYSTEMS - GUIDANCE FOR THE APPLICATION OF AQAP 2110 WITHIN AN EN 9100 QUALITY MANAGEMENT SYSTEM
TR 9135 : 1	AEROSPACE SERIES - QUALITY SYSTEMS - SPECIFIC QUALITY REQUIREMENTS FOR NATO SUPPLIERS
PREN 4805 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, STRAIGHT, IN HEAT RESISTING STEEL - INCH SERIES
PREN 9223-100 : DRAFT 2016	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 100: A GUIDE FOR THE APPLICATION OF THE PRINCIPLES OF CONFIGURATION MANAGEMENT
PREN 4854-2 : 200P1	AEROSPACE SERIES - BEARING, SPHERICAL PLAIN, IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER, LOW STARTING TORQUE AND LOW FRICTION COEFFICIENT, ELEVATED DUTY CYCLES UNDER LOW OSCILLATIONS AT DIFFERENT OPERATING CONDITIONS - PART 2: DIMENSIONS AND LOADS FOR WIDE SERIES
PREN 4729 : DRAFT 2015	AEROSPACE SERIES - TRIVALENT CHROMIUM BASED CHEMICAL CONVERSION COATINGS FOR ALUMINIUM AND ALUMINIUM ALLOYS
PREN 4812 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH NICKEL ALLOY C SEAL ON HEAT RESISTING STEEL PLATE WITH 4 FASTENING HOLES - INCH SERIES
PREN 4702-05 : DRAFT 2016	AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 05: RETAINING WASHER
PREN 4128 : 200P3	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE SHANK, SHORT THREAD, IN HEAT RESISTING NICKEL BASE ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1250 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
PREN 4072 : 200P3	AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, CLOSE TOLERANCE SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
PREN 4800-005 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 5: FORGING STOCK
PREN 4163 : 200P2	AEROSPACE SERIES - SCREWS 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
PREN 4697 : 200P2	AEROSPACE SERIES - GENERAL AND INSTALLATION REQUIREMENTS FOR PASSENGER SEAT FITTINGS
I.S. EN 3631:2014	AEROSPACE SERIES - FLUID FITTINGS, FLANGED, 90 DEGREES ELBOWED - SEALING BY O-RING FOR 0,8 MM THICK TUBES
PREN 4859 : DRAFT 2017	AEROSPACE SERIES - SENSOR BASED CLAMP LOAD DETERMINATION/HIGH TENSILE BOLTS - TECHNICAL SPECIFICATION
PREN 4138 : 200P2	AEROSPACE SERIES - SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
PREN 4801 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 3 FASTENING HOLES, IN HEAT RESISTING STEEL - INCH SERIES
PREN 4806 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, STRAIGHT, IN NICKEL ALLOY - INCH SERIES
I.S. EN 4074:2009	AEROSPACE SERIES - SCREWS, PAN HEAD, SIX LOBE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
PREN 4700-006 : 200P2	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS
PREN 4800-003 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 3: TUBE
PREN 4702-04 : DRAFT 2016	AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 04: SPRING CLAMP
PREN 3631 : 200P2	AEROSPACE SERIES - FLUID FITTINGS, FLAGED, 90 DEGREES ELBOWED - SEALING BY O-RING FOR 0,8 MM THICK TUBES
PREN 9136 : 2016	AEROSPACE SERIES - ROOT CAUSE ANALYSIS AND PROBLEM SOLVING (9S METHODOLOGY)
PREN 9145 : DRAFT 2016	AEROSPACE SERIES - REQUIREMENTS FOR ADVANCED PRODUCT QUALITY PLANNING AND PRODUCTION PART APPROVAL PROCESS
PREN 9278 : DRAFT 2017	AEROSPACE SERIES - GENERAL PRINCIPLES OF OBSOLESCENCE MANAGEMENT OF CHEMICALS, MATERIALS AND PROCESSES
PREN 4162 : 200P2	AEROSPACE SERIES - SCREWS 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
PREN 4818 : 200P1	AEROSPACE SERIES - PASSIVE HF RFID TAGS INTENDED FOR AIRCRAFT USE FOR AIRCRAFT USE
I.S. EN 3904:2017	AEROSPACE SERIES - WASHERS, WIRE LOCKING IN ALUMINIUM ALLOY, ANODIZED
IEC TS 62239-2:2017	Process management for avionics - Management plan - Part 2: Preparation and maintenance of an electronic COTS assembly management plan
I.S. EN 9223-100:2018	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 100: A GUIDE FOR THE APPLICATION OF THE PRINCIPLES OF CONFIGURATION MANAGEMENT
ISO 12319:2006	Aerospace 'P' (loop style) clamps Procurement specification
I.S. EN 4803:2017	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 4 FASTENING HOLES, IN HEAT RESISTING STEEL - INCH SERIES
I.S. EN 4707:2014	AEROSPACE SERIES - ACID PICKLING OF ALUMINUM AND ALUMINUM ALLOY WITHOUT HEXAVALENT CHROMIUM
I.S. EN 9223-102:2018	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 102: CONFIGURATION STATUS ACCOUNTING
I.S. EN 9117:2017	AEROSPACE SERIES - DELEGATED PRODUCT RELEASE VERIFICATION
I.S. EN 3908:2017	AEROSPACE SERIES - NIPPLES, LUBRICATING, AXIAL TYPE, IN CORROSION RESISTING STEEL, PASSIVATED
I.S. EN 4729:2017	AEROSPACE SERIES - TRIVALENT CHROMIUM BASED CHEMICAL CONVERSION COATINGS FOR ALUMINIUM AND ALUMINIUM ALLOYS
I.S. EN 2755:2009	AEROSPACE SERIES - BEARINGS, SPHERICAL PLAIN IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER - ELEVATED LOAD AT AMBIENT TEMPERATURE - TECHNICAL SPECIFICATION
I.S. EN 3539:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, ONE LUG, FIXED, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 4132:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 4125:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, REDUCED SERIES, WITH INCREMENTAL COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 4178:2017	AEROSPACE SERIES - SCREWS, PAN HEAD, SIX LOBE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
SAE AS 9138 : 2018	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS
NF EN 2862 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 90 DEGREES CORNER, WITH COUNTERBORE, IN ALLOY STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 4700-007:2010	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK
NF EN 3537 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
EN 9223-102:2018	Programme Management - Configuration Management - Part 102: Configuration status accounting
NF EN 4137 : 2010	AEROSPACE SERIES - BOLTS, NORMAL BIHEXAGONAL HEAD, STEPPED SHANK, LONG THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
NF EN 3389 : 2009	AEROSPACE SERIES - FASTENERS, EXTERNALLY THREADED, IN HEAT RESISTING NICKEL BASE ALLOY NI-PH1302 (WASPALOY) - CLASSIFICATION: 1210 MPA/730 DEGREES C - MANUFACTURING METHOD OPTIONAL - TECHNICAL SPECIFICATION
NF EN 4075 : 2008	AEROSPACE SERIES - SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, THREADED TO HEAD, IN CORROSION RESISTING STEEL, PASSIVATED, METRIC - CLASSIFICATION: 490 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
NF EN 3226 : 2010	AEROSPACE SERIES - NUTS, HEXAGON, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA/235 DEGREES C
NF EN 4700-007 : 2012	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK
I.S. EN 9104-002:2016	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - PART 002: REQUIREMENTS FOR OVERSIGHT OF AEROSPACE QUALITY MANAGEMENT SYSTEM REGISTRATION/CERTIFICATION PROGRAMS
BS EN 2888:2006	Aerospace series. Metric bolts, normal hexagon head, coarse tolerance normal shank, short thread, in corrosion resisting steel, passivated. Classification: 600 MPa (at ambient temperature) / 425°C
BS EN 3302:2017	Aerospace series. Bolts in heat resisting steel FE-PM1708 (FV535). Classification: 1 000 MPa/550 °C. Technical specification
BS EN 4311:2006	Aerospace series. Studs, coarse tolerance reduced shank, medium length threads, in heat and corrosion resisting steel, MoS<sub>2</sub> lubricated. Classification: 1100 MPa (at ambient temperature) / 315°C
BS EN 4166:2004	Aerospace series. Clips, spring tension, three parts. PTFE bushes
13/30278104 DC : 0	BS ISO 10327 - AIR CARGO - MAIN DECK CONTAINERS - DESIGN AND TESTING
BS EN 4494:2006	Aerospace series. Rings, split, in stainless steel
12/30263299 DC : 0	BS EN 4826 - AEROSPACE SERIES - ZINC-NICKEL (12/16% NI) PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS AND ALUMINIUM ALLOYS FOR PARTS AND FASTENERS
BS EN 3444:2006	Aerospace series. Bolt, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated. Classification: 1250 MPa (at ambient temperature) / 650°C
BS EN 2889:2006	Aerospace series. Metric bolts, normal hexagon head, coarse tolerance normal shank, short thread, in alloy steel, cadmium plated. Classification: 900 MPa (at ambient temperature) / 235°C
BS EN 2754:2006	Aerospace series. Nuts, anchor, self locking, two lug, floating with counterbore. Classification: 1100 MPa/235°C
EN 2133:2010	Aerospace series - Cadmium plating of steels with specified tensile strength ≤ 1 450 MPa, copper, copper alloys and nickel alloys
SBAC TS 157 : 6	AEROSPACE SECTOR CERTIFICATION SCHEME (ASCS) - REQUIREMENTS AND PROCEDURES
BS ISO 6517:2013	Air cargo. Certified lower deck containers. Design and testing
NF EN 4135 : 2010	AEROSPACE SERIES - BOLTS, NORMAL BI-HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
SAE AS 6023 : 2017	ACTIVE AND BATTERY ASSISTED PASSIVE TAGS INTENDED FOR AIRCRAFT USE
BS EN 6138:2017	Aerospace series. Cap, protective, non-metallic for fitting ends ≤ 3 000 PSI hydraulic systems
BS EN 4137:2009	Aerospace series. Bolts, normal bi-hexagonal head, stepped shank, long thread, in titanium alloy, anodized, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
17/30358538 DC : 0	BS EN 3275 - AEROSPACE SERIES - PIPE COUPLING 8 DEGREE 30 MINUTES UP TO 28000 KPA - DYNAMIC BEAM SEAL - METRIC SERIES - TECHNICAL SPECIFICATION
14/30311660 DC : 0	BS EN 9139 - AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - DEVELOPMENT OF PROCESS-BASED BODIES OF KNOWLEDGE
BS ISO 9940:2015	Aerospace series. Fluid, hydraulic, phosphate ester-base, fire resistant. Technical specification
I.S. EN 4807:2017	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, 90 DEGREES ELBOW, IN HEAT RESISTING STEEL - INCH SERIES
I.S. EN 4137:2009	AEROSPACE SERIES - BOLTS, NORMAL BI-HEXAGONAL HEAD, STEPPED SHANK, LONG THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 4700-006:2010	Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Pre-production and production forgings
I.S. EN 4297:2017	AEROSPACE SERIES - NUTS, HEXAGON, SELF-LOCKING BY PLASTIC RING, NORMAL HEIGHT, NORMAL ACROSS FLATS, IN CORROSION RESISTING STEEL, PASSIVATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/120 DEGREE C
UNI EN 3753 : 2011	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 60 DEGREES CORNER, WITH COUNTERBORE, IN ALLOY STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 4072:2016	AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, CLOSE TOLERANCE SHANK, SHORT THREAD IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
16/30342252 DC : 0	BS EN 8.3556 - AEROSPACE SERIES - SCREWS, PAN HEAD, SPIRAL DRIVE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
NF EN 4126 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUG, REDUCED SERIES, WITH INCREMENTAL COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 4309:2016	Aerospace series. Nuts, hexagon, self-locking by plastic ring, normal height, normal across flats, in alloy steel, cadmium plated. Classification: 900 MPa (at ambient temperature) / 120 °C
11/30243874 DC : 0	BS EN 8.4555 - AEROSPACE SERIES - ACID PICKLING OF ALUMINUM AND ALUMINUM ALLOY WITHOUT HEXAVALENT CHROMIUM
I.S. EN 3653:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, SELF-ALIGNING, ONE LUG, IN STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 3538:2010	Aerospace series. Nuts, anchor, self-locking, fixed, two lug, reduced series, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
BS EN 2043:2013	Aerospace series. Metallic materials. General requirements for semi-finished product qualification (excluding forgings and castings)
BS EN 4134:2009	Aerospace series. Bolts, normal hexagonal head, coarse tolerance normal shank, long thread, in heat resisting nickel base alloy, aluminium IVD coated. Classification: 1250 MPa (at ambient temperature)/425°C
SAE AS 9133 : 2016	QUALIFICATION PROCEDURE FOR AEROSPACE STANDARD PRODUCTS
16/30342246 DC : 0	BS EN 8.3555 - AEROSPACE SERIES - SCREWS, PAN HEAD, SPIRAL DRIVE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 3843:2010	Aerospace series. Nuts, bihexagonal, self-locking, with counterbore, in heat resisting steel, passivated. Classification: 1100 MPa (at ambient temperature)/650°C
BS EN 2867:2009	Aerospace series. Nuts, anchor, self-locking, floating, one lug, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature) / 315 °C
16/30342243 DC : 0	BS EN 8.3554 - AEROSPACE SERIES - SCREWS, PAN HEAD, SPIRAL DRIVE RECESS, THREADED TO HEAD, IN HEAT AND CORROSION RESISTING STEEL, PASSIVATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
09/30206914 DC : 0	BS EN 2596 - AEROSPACE SERIES - WASHERS, LOCK, WITH RADIAL SERRATIONS IN CORROSION RESISTING STEEL, CADMIUM PLATED FOR FLIGHT CONTROL RODS - DIMENSIONS
BS ISO 23933:2006	Aerospace series. Aramid reinforced lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 135°C/20 684 kPa (275°F/3 000 psi) and 135°C/21 000 kPa (275°F/3 046 psi). Procurement specification
BS EN 4163:2016	Aerospace series. Screws 100° countersunk normal head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1 100 MPa (at ambient temperature) / 235 °C
15/30328131 DC : 0	BS EN 3660-001 - AEROSPACE SERIES - CABLE OUTLET ACCESSORIES FOR CIRCULAR AND RECTANGULAR ELECTRICAL AND OPTICAL CONNECTORS - PART 001: TECHNICAL SPECIFICATION
14/30299616 DC : 0	BS EN 4474 - AEROSPACE SERIES - ALUMINIUM PIGMENTED COATINGS - COATING METHODS
BS EN 16603-31-02:2015	Space engineering. Two-phase heat transport equipment
I.S. EN 4134:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN HEAT RESISTING NICKEL BASE ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1250 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
16/30342254 DC : 0	BS EN 8.3558 - AEROSPACE SERIES- SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, SPIRAL DRIVE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 3539:2010	Aerospace series. Nuts, anchor, self-locking, one lug, fixed, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
EN 4700-002:2016	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 002: Bar and section
04/30115599 DC : DRAFT JUN 2004	ISO 8913 - AEROSPACE SERIES - LIGHTWEIGHT POLYTETRAFLUOROETHYLENE (PTFE) HOSE ASSEMBLIES, CLASSIFICATION 400 DEGREE F/3000 PSI, 204 DEGREE C/21000 KPA
15/30322457 DC : 0	BS EN 9223-104 - PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 104: CONFIGURATION CONTROL
BS EN 4106:2013	Aerospace series. Non-metallic materials. Structural adhesive systems. Paste adhesive. Technical specification
09/30206916 DC : 0	BS EN 2546 - AEROSPACE SERIES - WASHERS, LOCK WITH RADIAL SERRATIONS IN CORROSION RESISTING STEEL PASSIVATED FOR FLIGHT CONTROL RODS - DIMENSIONS
BS EN 4802:2017	Aerospace series. Flange couplings. Swivel flange with 3 fastening holes, in nickel alloy. Inch series
NF EN 3229 : 2010	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, REDUCED HEIGHT, NORMAL ACROSS FLATS, IN STEEL, CADMIUM PLATED, LEFT HAND THREAD - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
UNI EN 4800-004 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 004: WIRE
14/30298856 DC : 0	BS EN 9133 - AEROSPACE SERIES - QUALIFICATION PROCEDURE FOR AEROSPACE STANDARD PRODUCTS
EN 4702-05:2017	Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer
SAE AS 13004 : 2017	PROCESS FAILURE MODE AND EFFECTS ANALYSIS (PFMEA) AND CONTROL PLANS
NF EN 4700-005 : 2012	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK
NF EN 4127 : 2010	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
XP PREN 9111 : 2004 XP	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - ASSESSMENT APPLICABLE TO MAINTENANCE ORGANIZATIONS
BS EN 4129:2009	Aerospace series. Bolts, normal hexagonal head, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature) / 235°C
BS EN 9117:2017	Aerospace series. Delegated Product Release Verification
NF EN 2867 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, ONE LUG, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 3712:2007	Aerospace series. Nuts, anchor, self-locking, one lug, fixed, reduced series, with counterbore, in steel, cadmium plated, MoS2, lubricated. Classification: 1100 MPa (at ambient temperature)/235 °C
I.S. EN 4075:2008	AEROSPACE SERIES - SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, THREADED TO HEAD, IN CORROSION RESISTING STEEL, PASSIVATED - CLASSIFICATION: 490 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
BS EN 4075:2008	Aerospace series. Screws, pan head, offset cruciform recess, threaded to head, in corrosion resisting steel, passivated. Classification: 490 MPa (at ambient temperature) / 425 °C
UNI EN 4800-005 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK
I.S. EN 4818:2012	AEROSPACE SERIES - PASSIVE HF RFID TAGS INTENDED FOR AIRCRAFT USE
I.S. EN 4800-006:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS
PREN 2585 : DRAFT 2017	AEROSPACE SERIES - BEARING, SPHERICAL PLAIN IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER - WIDE SERIES - ELEVATED LOAD AT AMBIENT TEMPERATURE - DIMENSIONS AND LOADS
BS EN 4649:2009	Aerospace series. Handheld fire extinguishers with synthesis gases, for aircraft use. Technical specification and qualification conditions
I.S. EN 4071:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
PREN 16603-31-02 : DRAFT 2016	SPACE ENGINEERING - TWO-PHASE HEAT TRANSPORT EQUIPMENT
PREN 4474 : 200P2	AEROSPACE SERIES - ALUMINIUM PIGMENTED COATINGS - COATING METHODS
NF EN 2852 : 2010	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, HEAT RESISTING STEEL PASSIVATED - CLASSIFICATION: 1100 MPA/650 DEGREES C
NF EN 4800-003 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 003: TUBE
PREN 3660-001 : 200P3	AEROSPACE SERIES - CABLE OUTLET ACCESSORIES FOR CIRCULAR AND RECTANGULAR ELECTRICAL AND OPTICAL CONNECTORS - PART 001: TECHNICAL SPECIFICATION
PREN 6096 : DRAFT 2018	AEROSPACE SERIES - BEARING, SPHERICAL PLAIN WITH SELF-LUBRICATING LINER, EXTRA WIDE INNER RING IN CORROSION RESISTING STEEL - DIMENSIONS AND LOADS - INCH SERIES
XP PREN 9200 : 2002 XP	AEROSPACE SERIES - PROGRAMME MANAGEMENT - GUIDELINES FOR PROJECT MANAGEMENT SPECIFICATION
ISO/IEC TR 29110-5-1-4:2018	Systems and software engineering — Lifecycle profiles for Very Small Entities (VSEs) — Part 5-1-4: Software engineering: Management and engineering guidelines: Generic profile group: Advanced profile
PREN 3275 : 200P1	AEROSPACE SERIES - PIPE COUPLING 8 DEGREES 30 MINUTES UP TO 28000 KPA DYNAMIC BEAM SEAL - METRIC SERIES - TECHNICAL SPECIFICATION
I.S. EN 9104-003:2010	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - PART 003: REQUIREMENTS FOR AEROSPACE QUALITY MANAGEMENT SYSTEM (AQMS) AUDITOR TRAINING AND QUALIFICATION
I.S. EN 4809:2017	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH FLUOROCARBON SEAL ON ALUMINIUM PLATE WITH 3 FASTENING HOLES - INCH SERIES
PREN 9223-104 : DRAFT 2016	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 104: CONFIGURATION CONTROL
PREN 4800-001 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 1: PLATE, SHEET AND STRIP
PREN 4700-004 : 200P2	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 4: WIRE
PREN 4817 : 200P1	AEROSPACE SERIES PASSIVE UHF RFID TAGS INTENDED FOR AIRCRAFT USE
PREN 4510 : DRAFT 2017	AEROSPACE SERIES - PIPE COUPLING, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001, PORT ADAPTER, STRAIGHT, DOUBLE END, WITH LOCKING RING
PREN 4691-1 : DRAFT 2015	AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
PREN 3840 : 200P2	AEROSPACE SERIES - PAINTS AND VARNISHES - TECHNICAL SPECIFICATION
I.S. EN 4804:2017	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 4 FASTENING HOLES, IN NICKEL ALLOY - INCH SERIES
I.S. EN 4806:2017	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, STRAIGHT, IN NICKEL ALLOY - INCH SERIES
NF EN 4636 : 2009	AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK HEAD, SIX LOBE RECESS, SHORT THREAD, IN TITANIUM ALLOY TI-P64001, WITH ALUMINIUM PIGMENTED COATING - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 4808:2017	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, 90 DEGREES ELBOW, IN NICKEL ALLOY - INCH SERIES
SAE AS 9104 : 2017	REQUIREMENTS FOR AEROSPACE QUALITY MANAGEMENT SYSTEM CERTIFICATION/REGISTRATIONS PROGRAMS
I.S. EN 9115:2013	QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE ORGANIZATIONS - DELIVERABLE SOFTWARE (SUPPLEMENT TO EN 9100)
I.S. EN 4130:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
UNI EN 3538 : 2011	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 4644-001:2017	AEROSPACE SERIES - CONNECTOR, ELECTRICAL AND OPTICAL, RECTANGULAR, MODULAR, RECTANGULAR INSERTS, OPERATING TEMPERATURE 175 DEGREES C (OR 125 DEGREES C) CONTINUOUS - PART 001: TECHNICAL SPECIFICATION
BS EN 4644-001:2017	Aerospace series. Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 °C (or 125 °C) continuous Technical specification
BS EN 9101:2015	Quality Management Systems. Audit Requirements for Aviation, Space, and Defence Organisations
I.S. EN 16603-31-02:2015	SPACE ENGINEERING - TWO-PHASE HEAT TRANSPORT EQUIPMENT
I.S. EN 4800-002:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION
I.S. EN 4802:2017	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 3 FASTENING HOLES, IN NICKEL ALLOY - INCH SERIES
I.S. EN 2311:2017	AEROSPACE SERIES - BUSHES WITH SELF-LUBRICATING LINER - TECHNICAL SPECIFICATION
NF EN 4800-006 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS
NF EN 4800-002 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION
I.S. EN 2879:2017	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, AIR RESISTANT, SEALING, FLOATING, TWO LUG, WITH COUNTERBORE, IN CORROSION RESISTING STEEL, PASSIVATED, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
EN 9223-100:2018	Programme Management - Configuration Management - Part 100: A guide for the application of the principles of configuration management
UNI EN 4700-007 : 2011	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK
I.S. EN 4700-006:2010	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS
NF EN 4700-002 : 2012	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION
I.S. EN 2786:2008	AEROSPACE SERIES - ELECTROLYTIC SILVER PLATING OF FASTENERS
ISO/IEC TR 29110-5-6-2:2014	Systems and software engineering — Lifecycle profiles for Very Small Entities (VSEs) — Part 5-6-2: Systems engineering — Management and engineering guide: Generic profile group: Basic profile
EN 3875:2017	Aerospace series - Metallic materials, Filler metal for brazing - Technical specification
I.S. EN 9110:2015	QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION MAINTENANCE ORGANIZATIONS
BS EN 3052:2009	Aerospace series. Bolts, normal hexagonal head, close tolerance normal shank, short thread, in heat and corrosion resisting steel, passivated. Classification: 1100 MPa (at ambient temperature) / 425 °C
BS EN 3727:2006	Aerospace series. Bearings, airframe rolling rigid with flanged alignment housing. Technical specification
BS EN 3536:2006	Aerospace series. Nuts, hexagon, self-locking, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
BS EN 2311:2017	Aerospace series. Bushes with self-lubricating liner. Technical specification
I.S. EN 2337:2006	AEROSPACE SERIES - SPHERICAL PLAIN BEARINGS - TECHNICAL SPECIFICATION
I.S. EN 2888:2006	AEROSPACE SERIES - METRIC BOLTS, NORMAL HEXAGON HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN CORROSION RESISTING STEEL, PASSIVATED - CLASSIFICATION: 600 MPA (AT AMBIENT TEMPERATURE)/425 DEGREE C
I.S. EN 4168:2005	AEROSPACE SERIES - CLIPS, SPRING TENSION, THREE PARTS - OUTER CLIPS IN HEAT RESISTING STEEL FE-PA2601 (A286)
I.S. EN 4167:2005	AEROSPACE SERIES - CLIPS, SPRING TENSION, THREE PARTS - INNER CLIPS IN HEAT RESISTING STEEL FE-PA2601 (A286)
I.S. EN 2133:2010	AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS
I.S. EN 2549:2006	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1 100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
UNI EN 2133 : 2011	AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS
I.S. EN 3280:2011	AEROSPACE SERIES - BEARINGS, AIRFRAME ROLLING, RIGID OR SELF-ALIGNING - TECHNICAL SPECIFICATION
I.S. EN 3867:2005	AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGES IN TITANIUM ALLOY TI-P64001
I.S. EN 4115:2010	AEROSPACE SERIES - CUSHION, RUBBER FOR CLAMPS - DIMENSIONS, MASSES
I.S. EN 3820:2017	AEROSPACE SERIES - METRIC BOLTS, NORMAL HEXAGON HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
I.S. EN 3868:2005	AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGE CONNECTORS, WELDED, IN TITANIUM ALLOY TI-P64001
I.S. EN 9111:2006	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - ASSESSMENT APPLICABLE TO MAINTENANCE ORGANIZATIONS
I.S. EN 2889:2006	AEROSPACE SERIES - METRIC BOLTS, NORMAL HEXAGON HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
I.S. EN 4166:2005	AEROSPACE SERIES - CLIPS, SPRING TENSION, THREE PARTS - PTFE BUSHES
I.S. EN 9121:2009	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - ASSESSMENT APPLICABLE TO STOCKIST DISTRIBUTORS
I.S. EN 2859:2006	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN ALLOY STEEL, CADMIUM PLATED, METRIC SERIES - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
I.S. EN 2491:2011	AEROSPACE SERIES - MOLYBDENUM DISULPHIDE DRY LUBRICANTS - COATING METHODS
SBAC TS 202 : 2013	QUALIFICATION TEST REQUIREMENTS & PROCEDURES FOR AEROSPACE INDUSTRY STANDARD PARTS
I.S. EN 3840:2007	AEROSPACE SERIES - PAINTS AND VARNISHES - TECHNICAL SPECIFICATION
BS EN 4073:2016	Aerospace series. Screws, pan head, hexalobular recess, coarse tolerance shank, medium length thread, in alloy steel, cadmium plated. Classification: 1 100 MPa (at ambient temperature) / 235 °C
UNI EN 2863 : 2011	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 90 DEGREES CORNER, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 3227:2010	Aerospace series. Nuts, hexagonal, plain, normal height, normal across flats, in steel, cadmium plated, left hand thread. Classification: 1100 MPa (at ambient temperature)/235°C
SAE AS 9012 : 2003	AEROSPACE FIRST ARTICLE INSPECTION REQUIREMENT
SAE AS 9162 : 2016	AEROSPACE OPERATOR SELF-VERIFICATION PROGRAMS
BS EN 9137:2012	Quality management systems. Guidance for the Application of AQAP 2110 within an EN 9100 Quality Management System
13/30279205 DC : 0	BS EN 9101 - QUALITY MANAGEMENT SYSTEMS - AUDIT REQUIREMENTS FOR AVIATION, SPACE, AND DEFENCE ORGANISATIONS
I.S. EN 3228:2010	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, REDUCED HEIGHT, NORMAL ACROSS FLATS, IN STEEL, CADMIUM PLATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 4700-004:2010	Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Wire
BS EN 4702-03:2017	Aerospace series. Quick release fastening systems for non-structural and lining applications Stud - quick-release and locking
16/30342237 DC : 0	BS EN 8.3553 - AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, SPIRAL DRIVE RECESS, SHORT THREAD, IN HEAT RESISTING STEEL FE-PA2601 (A286), PASSIVATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C
BS EN 3226:2009	Aerospace series. Nuts, hexagon, plain, normal height, normal across flats, steel, cadmium plated. Classification: 1100 MPa/235°C
I.S. EN 3757:2009	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, SELF-ALIGNING, TWO LUGS, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
BS EN 4136:2009	Aerospace series. Bolts, normal bi-hexagonal head, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1100 MPa at ambient temperature)/235°C
BS EN 4806:2017	Aerospace series. Flange couplings. Weld coupling, straight, in nickel alloy. Inch series
NF EN 4800-005 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK
12/30260907 DC : 0	BS EN 4712 - AEROSPACE SERIES - NUTS, 12-POINT FLANGE, SELF-LOCKING, CONTINUOUS FIBRE REINFORCED-PEEK COMPOSITE, TEMPERATURE RANGE -65 DEGREES C TO 135 DEGREES C - INCH SERIES
UNI EN 4700-005 : 2011	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK
UNI EN 3768 : 2012	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, ONE LUG, FIXED, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
SAE AS 9145 : 2016	AEROSPACE SERIES - REQUIREMENTS FOR ADVANCED PRODUCT QUALITY PLANNING AND PRODUCTION PART APPROVAL PROCESS
13/30288694 DC : 0	BS EN 4073 - AEROSPACE SERIES - SCREWS, PAN HEAD, SIX LOBE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 4700-002:2016	Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Bar and section
BS EN 2869:2009	Aerospace series. Nuts, hexagonal, slotted/castellated, normal height, normal accross flats, in heat resisting steel, passivated. Classification: 1100 MPa (at ambient temperature) / 650°C
17/30356163 DC : 0	BS EN 4859 - AEROSPACE SERIES - SENSOR BASED CLAMP LOAD DETERMINATION/HIGH TENSILE BOLTS - TECHNICAL SPECIFICATION
16/30352094 DC : DRAFT NOV 2016	BS EN 2894 - AEROSPACE SERIES - NUTS, BIHEXAGONAL, SELF-LOCKING, WITH COUNTERBORE, IN HEAT RESISTING NICKEL BASE ALLOY, PASSIVATED, MOS[2] LUBRICATED - CLASSIFICATION: 1550 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 2863:2010	Aerospace series. Nuts, anchor, self-locking, fixed, 90° corner, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature) / 315°C
14/30302298 DC : 0	BS ISO 9940 - AEROSPACE SERIES - FLUID, HYDRAULIC, PHOSPHATE ESTER-BASE, FIRE RESISTANT - TECHNICAL SPECIFICATION
UNI EN 4700-004 : 2011	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 004: Wire
NF EN 3228 : 2010	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, REDUCED HEIGHT, NORMAL ACROSS FLATS, IN STEEL, CADMIUM PLATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 4702-04:2017	Aerospace series. Quick release fastening systems for non-structural and lining applications Spring clamp
BS EN 2865:2009	Aerospace series. Nuts, anchor, self-locking, floating, two lugs, with counterbore, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature) / 315 °C
BS EN 4800-006:2010	Aerospace series. Titanium and titanium alloys. Technical specification Pre-production and production forgings
BS EN 4800-005:2010	Aerospace series. Titanium and titanium alloys. Technical specification Forging stock
UNI EN 3843 : 2010	AEROSPACE SERIES - NUTS, BIHEXAGONAL, SELF-LOCKING, WITH COUNTERBORE, IN HEAT RESISTING STEEL, PASSIVATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C
16/30342183 DC : 0	BS EN 8.3552 - AEROSPACE SERIES- SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, SPIRAL DRIVE RECESS, THREADED TO HEAD, IN HEAT AND CORROSION RESISTING STEEL, PASSIVATED - CLASSIFICATION : 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
I.S. EN 2043:2013	AEROSPACE SERIES - METALLIC MATERIALS - GENERAL REQUIREMENTS FOR SEMI-FINISHED PRODUCT QUALIFICATION (EXCLUDING FORGINGS AND CASTINGS)
BS EN 4133:2009	Aerospace series. Bolts, normal hexagonal head, coarse tolerance normal shank, long thread, in titanium alloy, aluminium IVD coated. Classification: 1100 MPa (at ambient temperature) / 425 °C
04/30116688 DC : DRAFT JUL 2004	EN 9135 - AEROSPACE SERIES - QUALITY SYSTEMS - SPECIFIC QUALITY REQUIREMENTS FOR NATO SUPPLIERS
BS EN 4800-004:2010	Aerospace series. Titanium and titanium alloys. Technical specification Wire
11/30245736 DC : 0	BS EN 3631 - AEROSPACE SERIES - FLUID FITTINGS, FLANGED, 90 DEGREE ELBOWED - SEALING BY O-RING FOR 0,8 MM THICK TUBES
13/30291179 DC : 0	BS EN 4697 - AEROSPACE SERIES - GENERAL AND INSTALLATION REQUIREMENTS FOR PASSENGER SEAT FITTINGS
BS EN 4127:2009	Aerospace series. Bolts, normal hexagonal head, coarse tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated. Classification: 1100 MPa (at ambient temperature)/ 425 °C
BS EN 4813:2017	Aerospace series. Flange couplings. Cap, in heat resisting steel. Inch series
17/30364785 DC : 0	BS EN 4868 - AEROSPACE SERIES - ANODIC ELECTRODEPOSITION OF PRIMER
UNI EN 4800-008 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS
BS EN 2755:2009	Aerospace series. Bearings, spherical plain in corrosion resisting steel with self-lubricating liner. Elevated load at ambient temperature. Technical specification
14/30310862 DC : 0	BS EN 4832 - AEROSPACE SERIES - ADAPTOR, PIPE COUPLING 24 DEGREES CONE UP TO 35000 KPA (5080 PSI) RING-LOCKED FITTING AND RING-LOCKED FITTING-REDUCER - INCH SERIES - TECHNICAL SPECIFICATION
NF EN 2863 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 90 DEGREES CORNER, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 2866:2009	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, ONE LUG, WITH COUNTERBORE, IN STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1110 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
NF EN 4700-006 : 2012	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS
I.S. EN 3435:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUG, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 4804:2017	Aerospace series. Flange couplings. Swivel flange with 4 fastening holes, in nickel alloy. Inch series
15/30322445 DC : 0	BS EN 9223-100 - PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 100: A GUIDE FOR THE APPLICATION OF THE PRINCIPLES OF CONFIGURATION MANAGEMENT
BS EN 4819:2012	Aerospace series. Contact Memory Button (CMB) tags intended for aircraft use
XP PREN 9120 : 2004 XP	AEROSPACE SERIES - QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE APPLICABLE TO STOCKIST DISTRIBUTORS
07/30164110 DC : 0	BS EN 9131 - AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - NONCONFORMANCE DOCUMENTATION
EN 4702-03:2017	Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 03: Stud - quick-release and locking
BS EN 2786:2008	Aerospace series. Electrolytic silver plating of fasteners
PREN 9133 : 200P1	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - QUALIFICATION PROCEDURE FOR AEROSPACE STANDARD PRODUCTS
UNE-EN 9116:2016	Aerospace series - Notice of Change (NOC) Requirements
07/30165636 DC : 0	BS EN 4636 - AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK HEAD, SIX LOBES RECESS, SHORT THREAD, IN TITANIUM ALLOY TI-P64001, WITH ALUMINIUM PIGMENTED COATING - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
NF EN 3227 : 2010	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, IN STEEL, CADMIUM PLATED, LEFT HAND THREAD - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
PREN 4808 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, 90 DEGREES ELBOW, IN NICKEL ALLOY - INCH SERIES
PREN 4702-03 : DRAFT 2016	AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
PREN 9138 : 200P1	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS
PREN 9102 : 200P3	AEROSPACE SERIES - QUALITY SYSTEMS - FIRST ARTICLE INSPECTION REQUIREMENT
ISO 10327:2014	Air cargo Main deck containers Design and testing
PREN 9223-101 : DRAFT 2016	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 101: CONFIGURATION IDENTIFICATION
PREN 9131 : 200P4	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - NONCONFORMANCE DATA DEFINITION AND DOCUMENTATION
PREN 3280 : 200P2	AEROSPACE SERIES - BEARING, AIRFRAME ROLLING, RIGID OR SELF-ALIGNING - TECHNICAL SPECIFICATION
I.S. EN 3763:2010	AEROSPACE SERIES - NUTS, HEXAGONAL, SELF-LOCKING, BALL SEAT, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
SAE AS 13001A : 2017	DELEGATED PRODUCT RELEASE VERIFICATION TRAINING REQUIREMENTS
SAE AS 9117 : 2016	DELEGATED PRODUCT RELEASE VERIFICATION
NF EN 4499 : 2009	AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK REDUCED HEAD, OFFSET CRUCIFORM RECESS, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ANODIZED, WITH ALUMINIUM PIGMENTED COATING - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
14/30315275 DC : 0	BS EN 9162 - AEROSPACE OPERATOR SELF-VERIFICATION PROGRAMS
I.S. EN 9223-104:2018	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 104: CONFIGURATION CONTROL
NF EN 2865 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUGS, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 4691-1:2017	AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
I.S. EN 3777:2010	AEROSPACE SERIES - PINS, QUICK RELEASE, SINGLE AND DOUBLE ACTING - TECHNICAL SPECIFICATION
I.S. EN 4700-001:2010	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP
I.S. EN 4697:2016	AEROSPACE SERIES - GENERAL AND INSTALLATION REQUIREMENTS FOR PASSENGER SEAT FITTINGS
UNI EN 4106 : 2014	AEROSPACE SERIES - NON-METALLIC MATERIALS - STRUCTURAL ADHESIVE SYSTEMS - PASTE ADHESIVE - TECHNICAL SPECIFICATION
SAE AS9101F:2016	QUALITY MANAGEMENT SYSTEMS - AUDIT REQUIREMENTS FOR AVIATION, SPACE, AND DEFENSE ORGANIZATIONS
BS EN 9104-001:2013	Aerospace series. Quality management systems Requirements for Aviation, Space, and Defence Quality Management System Certification Programs
I.S. EN 2862:2009	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 90 DEGREE CORNER, WITH COUNTERBORE, IN ALLOY STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
UNI EN 4700-003 : 2011	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 003: TUBE
NF EN 4700-003 : 2012	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 003: TUBE
I.S. EN 4309:2016	AEROSPACE SERIES - NUTS, HEXAGON, SELF-LOCKING BY PLASTIC RING, NORMAL HEIGHT, NORMAL ACROSS FLATS, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/120 DEGREE C
I.S. EN 4826:2014	AEROSPACE SERIES - ZINC-NICKEL (12%-16% NI) PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER ALLOYS, NICKEL ALLOYS AND ALUMINIUM ALLOYS FOR PARTS AND FASTENERS
I.S. EN 4073:2016	AEROSPACE SERIES - SCREWS, PAN HEAD, HEXALOBULAR RECESS, COARSE TOLERANCE SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 4800-004:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 004: WIRE
EN 4691-1:2017	Aerospace series - Tie rod with integrated bolts - Part 1: Technical specification
ISO 9940:2015	Aerospace series Fluid, hydraulic, phosphate ester-base, fire resistant Technical specification
I.S. EN 9137:2012	QUALITY MANAGEMENT SYSTEMS - GUIDANCE FOR THE APPLICATION OF AQAP 2110 WITHIN AN EN 9100 QUALITY MANAGEMENT SYSTEM
I.S. EN 9131:2016	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - NONCONFORMANCE DATA DEFINITION AND DOCUMENTATION
UNI EN 4800-007 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK
NF EN 4074 : 2010	AEROSPACE SERIES - SCREWS, PAN HEAD, SIX LOBE RECESS COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
EN 4702-04:2017	Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 04: Spring clamp
NF EN 4132 : 2010	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
NF EN 4071 : 2010	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
NF EN 3763 : 2010	AEROSPACE SERIES - NUTS, HEXAGONAL, SELF-LOCKING, BALL SEAT, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
UNI EN 2852 : 2011	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, HEAT RESISTING STEEL PASSIVATED - CLASSIFICATION: 1100 MPA/650 DEGREES C
BS EN 4161:2009	Aerospace series. Screws, pan head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature) / 235 °C
NF EN 3388 : 2009	AEROSPACE SERIES - FASTENERS, EXTERNALLY THREADED, IN HEAT RESISTING NICKEL BASE ALLOY NI-PH2601 (INCONEL 718) - CLASSIFICATION: 1275 MPA/650 DEGREES C - MANUFACTURING METHOD OPTIONAL - TECHNICAL SPECIFICATION
EN 9223-101:2018	Programme Management - Configuration Management - Part 101: Configuration identification
UNI EN 3227 : 2011	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, IN STEEL, CADMIUM PLATED, LEFT HAND THREAD - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
NF EN 3712 : 2008	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, ONE LUG, FIXED, REDUCED SERIES, WITH COUNTERBORE, IN STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
IEC TS 62668-2:2016	Process management for avionics - Counterfeit prevention - Part 2: Managing electronic components from non-franchised sources
ISO 14300-2:2011	Space systems — Programme management — Part 2: Product assurance
I.S. EN 4131:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN HEAT RESISTING NICKEL BASE ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1250 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
EN 4707:2014	Aerospace series - Acid pickling of aluminum and aluminum alloy without hexavalent chromium
DIN EN 3660-001:2016-04	AEROSPACE SERIES - CABLE OUTLET ACCESSORIES FOR CIRCULAR AND RECTANGULAR ELECTRICAL AND OPTICAL CONNECTORS - PART 001: TECHNICAL SPECIFICATION
BS EN 4826:2014	Aerospace series. Zinc-Nickel (12 %-16 % Ni) plating of steels with specified tensile strength ≤ 1 450 MPa, copper alloys, nickel alloys and aluminium alloys for parts and fasteners
BS EN 4168:2004	Aerospace series. Clips, spring tension, three parts. Outer clips in heat resisting steel FE-PA2601 (A286)
BS EN 4167:2004	Aerospace series. Clips, spring tension, three parts. Inner clips in heat resisting steel FE-PA2601 (A286)
BS EN 3431:2007	Aerospace series. Nuts, hexagonal, self-locking, with counterbore and captive washer, in heat resisting steel, silver plated. Classification: 1100 MPa (at ambient temperature)/425°C
BS EN 4498:2005	Aerospace series. Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated, with aluminium pigmented coating. Classification: 1 550 MPa (at ambient temperature) / 315 °C
EN 9131:2016	Aerospace series - Quality Management Systems - Nonconformance Data Definition and Documentation
EN 2869:2009	Aerospace series - Nuts, hexagonal, slotted/castellated, normal height, normal accross flats, in heat resisting steel, passivated - Classification: 1 100 MPa (at ambient temperature) / 650 °C
EN 4806:2017	Aerospace series - Flange couplings - Weld coupling, straight, in nickel alloy - Inch series
EN 4497:2005	Aerospace series - Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 2889:2006	Aerospace series - Metric bolts, normal hexagon head, coarse tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 900 MPa (at ambient temperature)/235 °C
UNI EN 2491 : 2012	AEROSPACE SERIES - MOLYBDENUM DISULPHIDE DRY LUBRICANTS - COATING METHODS
UNI EN 4115 : 2011	AEROSPACE SERIES - CUSHION, RUBBER FOR CLAMPS - DIMENSIONS, MASSES
EN 4801:2017	Aerospace series - Flange couplings - Swivel flange with 3 fastening holes, in heat resisting steel - Inch series
EN 4805:2017	Aerospace series - Flange couplings - Weld coupling, straight, in heat resisting steel - Inch series
UNI EN 4131 : 2013	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN HEAT RESISTING NICKEL BASE ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1250 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
UNI EN 3280 : 2011	AEROSPACE SERIES - BEARINGS, AIRFRAME ROLLING, RIGID OR SELF-ALIGNING - TECHNICAL SPECIFICATION
UNI EN 3777 : 2010	AEROSPACE SERIES - PINS, QUICK RELEASE, SINGLE AND DOUBLE ACTING - TECHNICAL SPECIFICATION
UNI EN 4800-001 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP
13/30288692 DC : 0	BS EN 4178 - AEROSPACE SERIES - SCREWS, PAN HEAD, SIX LOBE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
15/30322454 DC : 0	BS EN 9223-103 - PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 103: CONFIGURATION VERIFICATIONS, REVIEWS AND AUDITS
ISO/IEC TR 29110-5-1-3:2017	Systems and software engineering — Lifecycle profiles for Very Small Entities (VSEs) — Part 5-1-3: Software engineering — Management and engineering guide: Generic profile group — Intermediate profile
BS EN 3389:2009	Aerospace series. Fasteners, externally threaded, in heat resisting nickel base alloy NI-PH1302 (Waspaloy). Classification: 1210 MPa/730°C. Manufacturing method optional. Technical specification
BS EN 4128:2016	Aerospace series. Bolts, normal hexagonal head, coarse tolerance shank, short thread, in heat resisting nickel base alloy, aluminium IVD coated. Classification: 1 250 MPa (at ambient temperature) / 425 °C
XP PREN 9101 : 2010 XP	QUALITY MANAGEMENT SYSTEMS - AUDIT REQUIREMENTS FOR AVIATION, SPACE, AND DEFENSE ORGANIZATIONS
14/30296344 DC : 0	BS EN 3820 - AEROSPACE SERIES - METRIC BOLTS, NORMAL HEXAGON HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION; 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
PD IEC/TS 62239-2:2017	Process management for avionics. Management plan Preparation and maintenance of an electronic COTS assembly management plan
BS EN 4126:2010	Aerospace series. Nuts, anchor, self-locking, floating, two lug, reduced series, with incremental counterbore, in heat resisting steel, MoS2 lubricated. Classification: 900 MPa (at ambient temperature)/315°C
BS EN 3753:2010	Aerospace series. Nuts, anchor, self-locking, fixed, 60° corner, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/235°C
UNI EN 9104-003 : 2011	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - PART 003: REQUIREMENTS FOR AEROSPACE QUALITY MANAGEMENT SYSTEM (AQMS) AUDITOR TRAINING AND QUALIFICATION
BS EN 3229:2009	Aerospace series. Nuts, hexagonal, plain, reduced height, normal across flats, in steel, cadmium plated, left hand thread. Classification: 900 MPa (at ambient temperature)/235°C
NF EN 4800-008 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS
NF EN 4800-007 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK
UTEC 96 027-1 : 2011	ELECTRONIC EQUIPMENT OBSOLESCENCE - GUIDE APPLIED OBSOLESCENCE MANAGEMENT
SBAC TS 157 : 6	AEROSPACE SECTOR CERTIFICATION SCHEME (ASCS) - REQUIREMENTS AND PROCEDURES
BS EN 4800-008:2010	Aerospace series. Titanium and titanium alloys. Technical specification Pre-production and production castings
NF EN 4084 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, WITH COUNTERBORE, IN ALLOY STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
14/30296592 DC : 0	BS EN 4474 - AEROSPACE SERIES - ALUMINIUM PIGMENTED COATINGS - COATING METHODS
BS EN 4729:2017	Aerospace series. Trivalent chromium based chemical conversion coatings for aluminium and aluminium alloys
BS EN 4805:2017	Aerospace series. Flange couplings. Weld coupling, straight, in heat resisting steel. Inch series
09/30212012 DC : 0	BS EN 2894 - AEROSPACE SERIES - NUTS, BIHEXAGONAL, SELF-LOCKING, WITH COUNTERBORE, IN HEAT RESISTING NICKEL BASE ALLOY, PASSIVATED, MOS2 LUBRICATED - CLASSIFICATION: 1550 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
UNI EN 4800-003 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 003: TUBE
13/30290108 DC : 0	BS EN 4128 - AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN HEAT RESISTING NICKEL BASE ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1250 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
NF EN 3539 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, ONE LUG, FIXED, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 4072:2016	Aerospace series. Screws, 100° countersunk normal head, offset cruciform recess, close tolerance shank, short thread in titanium alloy, aluminium IVD coated. Classification: 1 100 MPa (at ambient temperature) / 425 °C
BS EN 2879:2017	Aerospace series. Nuts, anchor, self-locking, air resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS2 lubricated. Classification: 900 MPa (at ambient temperature) / 235 °C
16/30244282 DC : 0	BS EN 9115 - QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE ORGANIZATIONS - DELIVERABLE SOFTWARE (SUPPLEMENT TO EN 9100)
I.S. EN 4135:2009	AEROSPACE SERIES - BOLTS, NORMAL BI-HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
12/30264438 DC : 0	BS ISO 6517 - AIR CARGO - CERTIFIED LOWER DECK CONTAINERS - DESIGN AND TESTING
15/30323937 DC : 0	BS EN 3302 - AEROSPACE SERIES - BOLTS IN HEAT RESISTING STEEL FE-PM1708 (FV535) - CLASSIFICATION: 1000 MPA/550 DEGREES C - TECHNICAL SPECIFICATION
13/30286760 DC : 0	BS EN 9102 - AEROSPACE FIRST ARTICLE INSPECTION REQUIREMENT
BS EN 4499:2009	Aerospace series. Screws, 100° countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating. Classification: 1100 MPa (at ambient temperature) / 315 °C
NF EN 4125 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, REDUCED SERIES, WITH INCREMENTAL COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
PD ISO/IEC TR 29110-5-1-3:2017	Systems and software engineering. Lifecycle profiles for Very Small Entities (VSEs) Software engineering. Management and engineering guide: Generic profile group. Intermediate profile
13/30290264 DC : 0	BS EN 4163 - AEROSPACE SERIES - SCREWS 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
13/30290082 DC : 0	BS EN 4072 - AEROSPACE SERIES - SCREWS, 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
I.S. EN 9103:2014	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - VARIATION MANAGEMENT OF KEY CHARACTERISTICS
BS EN 4084:2009	Aerospace series. Nuts, anchor, self-locking, fixed, two lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature) / 235°C
BS EN 3768:2012	Aerospace series. Nuts. anchor, self-locking, one lug, fixed, reduced series, with counterbore, in heat resisting steel, MoS2lubricated. Classification: 1 100 MPa (at ambient temperature)/315 °C
12/30260906 DC : 0	BS EN 4711 - AEROSPACE SERIES - SCREW, 12-POINT FLANGE HEAD (BI HEXAGONAL HEAD BOLT), LONG THREAD, FOR TENSILE APPLICATIONS, CONTINUOUS FIBRE REINFORCED-PEEK COMPOSITE, TEMPERATURE RANGE -65 DEGREES C TO 135 DEGREES C - INCH SERIES
BS EN 4818:2012	Aerospace series. Passive HF RFID tags intended for aircraft use
BS EN 4474:2009	Aerospace series. Aluminium pigmented coatings. Coating methods
BS EN 4135:2009	Aerospace series. Bolts, normal bi-hexagonal head, coarse tolerance normal shank, medium length thread, in titanium alloy, anodized, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
PD ISO/IEC TR 29110-5-6-2:2014	Systems and software engineering. Lifecycle profiles for Very Small Entities (VSEs) Systems engineering. Management and engineering guide: Generic profile group: Basic profile
BS EN 4700-003:2010	Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Tube
BS EN 4800-001:2010	Aerospace series. Titanium and titanium alloys. Technical specification Plate, sheet and strip
16/30339916 DC : 0	BS EN 2133 - AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS
BS EN 3903:2017	Aerospace series. Washers, laminated, in corrosion resisting steel
BS EN 4808:2017	Aerospace series. Flange couplings. Weld coupling, 90° elbow, in nickel alloy. Inch series
BS ISO 14300-2:2011	Space systems. Programme management Product assurance
16/30354035 DC : 0	BS EN 4854-2 - AEROSPACE SERIES - BEARINGS, SPHERICAL PLAIN, IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER, LOW STARTING TORQUE AND LOW FRICTION COEFFICIENT, ELEVATED DUTY CYCLES UNDER LOW OSCILLATIONS AT DIFFERENT OPERATING CONDITIONS, WIDE SERIES - DIMENSIONS AND LOADS
BS EN 4162:2016	Aerospace series. Screws 100° countersunk normal head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1 100 MPa (at ambient temperature) / 235 °C
BS EN 4130:2009	Aerospace series. Bolts, normal hexagonal head, coarse tolerance normal shank, medium length thread, in titanium alloy, aluminium IVD coated. Classification: 1100 MPa (at ambient temperature) / 425 °C
BS EN 3631:2014	Aerospace series. Fluid fittings, flanged, 90° elbowed. Sealing by O-ring for 0,8 mm thick tubes
17/30318744 DC : 0	BS ISO 20188 - SPACE SYSTEMS - PRODUCT ASSURANCE REQUIREMENTS FOR COMMERCIAL SATELLITES
17/30366369 DC : 0	BS EN 2133 AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS
BS EN 3388:2009	Aerospace series. Fasteners, externally threaded, in heat resisting nickel base alloy NI-PH2601 (Inconel 718). Classification 1275 MPa/650°C. Manufacturing method optional. Technical specification
09/30214446 DC : 0	BS EN 2491 - AEROSPACE SERIES MOLYBDENUM DISULPHIDE DRY LUBRICANTS COATING METHODS
13/30287034 DC : 0	BS EN 3660-001 - AEROSPACE SERIES - CABLE OUTLET ACCESSORIES FOR CIRCULAR AND RECTANGULAR ELECTRICAL AND OPTICAL CONNECTORS - PART 001: TECHNICAL SPECIFICATION
16/30346081 DC : 0	BS EN 4510 - AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREE, SPHERICAL IN TITANIUM ALLOY TIP64001 - ADAPTERS, STRAIGHT, DOUBLE END, WITH LOCKING RING
11/30253929 DC : 0	BS EN 4820 - AEROSPACE SERIES - COPPER AND COPPER ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION
UNI EN 2043 : 2014	AEROSPACE SERIES - METALLIC MATERIALS - GENERAL REQUIREMENTS FOR SEMI-FINISHED PRODUCT QUALIFICATION (EXCLUDING FORGINGS AND CASTINGS)
UNI EN 4707 : 2014	AEROSPACE SERIES - ACID PICKLING OF ALUMINUM AND ALUMINUM ALLOY WITHOUT HEXAVALENT CHROMIUM
BS EN 4800-002:2010	Aerospace series. Titanium and titanium alloys. Technical specification Bar and section
I.S. EN 3229:2009	AEROSPACE SERIES - NUTS, HEXAGONAL, PLAIN, REDUCED HEIGHT, NORMAL ACROSS FLATS, IN STEEL, CADMIUM PLATED, LEFT HAND THREAD - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
BS EN 4800-003:2010	Aerospace series. Titanium and titanium alloys. Technical specification Tube
BS EN 9115:2013	Quality Management Systems. Requirements for Aviation, Space and Defense Organizations. Deliverable Software (Supplement to EN 9100)
NF EN 2883 : 2010	AEROSPACE SERIES - NUTS, HEXAGONAL, SELF-LOCKING, WITH COUNTERBORE AND CAPTIVE WASHER, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
NF EN 9133 : 2005	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - QUALIFICATION PROCEDURE FOR AEROSPACE STANDARD PARTS
14/30311577 DC : DRAFT AUG 2014	BS EN 2311 - AEROSPACE SERIES - BUSHES WITH SELF-LUBRICATING LINER - TECHNICAL SPECIFICATION
PREN 2584 : DRAFT 2017	AEROSPACE SERIES - BEARING, SPHERICAL PLAIN IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER - NARROW SERIES - ELEVATED LOAD AT AMBIENT TEMPERATURE - DIMENSIONS AND LOADS
NF EN 2866 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, ONE LUG, WITH COUNTERBORE, IN STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1110 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
NF EN 4700-001 : 2012	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP
BS EN 4131:2009	Aerospace series. Bolts, normal hexagonal head, coarse tolerance normal shank, medium length thread, in heat resisting nickel base alloy, aluminium IVD coated. Classification: 1250 MPa (at ambient temperature) / 425 °C
NF EN 4700-004 : 2012	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 004: WIRE
PREN 6138 : DRAFT 2014 CORR 14	AEROSPACE SERIES - CAPS, PROTECTIVE, NON-METALLIC FOR FLARED AND FLARELESS FITTING ENDS, FOR FLUID SYSTEMS WITH <= 3000 PSI (21000 KPA) WORKING PRESSURE
PREN 4700-003 : 200P2	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 003: TUBE
PREN 9223-103 : DRAFT 2016	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 103: CONFIGURATION VERIFICATIONS, REVIEWS AND AUDITS
PREN 6097 : DRAFT 2018	AEROSPACE SERIES - BEARING, SPHERICAL PLAIN, METAL TO METAL, EXTRA WIDE INNER RING IN CORROSION RESISTING STEEL - DIMENSIONS AND LOADS - INCH SERIES
PREN 4802 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 3 FASTENING HOLES, IN NICKEL ALLOY - INCH SERIES
PREN 4809 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH FLUOROCARBON SEAL ON ALUMINIUM PLATE WITH 3 FASTENING HOLES - INCH SERIES
BS EN 9131:2016	Aerospace series. Quality Management Systems. Nonconformance Data Definition and Documentation
NF EN 4136 : 2010	AEROSPACE SERIES - BOLTS, NORMAL BI-HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
PREN 9121 : 200P3	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - ASSESSMENT APPLICABLE TO STOCKIST DISTRIBUTORS
NF EN 4800-004 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 004: WIRE
SAE AMS 3095 : 2004	PAINT: HIGH GLOSS FOR AIRLINE EXTERIOR SYSTEM
PREN 9162 : 200P1	AEROSPACE SERIES - AEROSPACE OPERATOR SELF-VERIFICATION PROGRAMS
PREN 9104 : 200P1	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AEROSPACE QUALITY MANAGEMENT SYSTEM CERTIFICATION/REGISTRATIONS PROGRAMS
PREN 4649 : 200P1	AEROSPACE SERIES - HANDHELD FIRE EXTINGUISHERS WITH SYNTHESIS GASES, FOR AIRCRAFT USE - TECHNICAL SPECIFICATION AND QUALIFICATION CONDITIONS
PREN 4707 : 200P1	AEROSPACE SERIES - ACID PICKLING OF ALUMINIUM AND ALUMINIUM ALLOYS WITHOUT HEXAVALENT CHROMIUM
PREN 4800-002 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 2: BAR AND SECTION
PREN 4800-008 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 8: PRE-PRODUCTION AND PRODUCTION CASTINGS
PREN 4073 : 200P2	AEROSPACE SERIES - SCREWS, PAN HEAD, SIX LOBE RECESS, COARSE TOLERANCE SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
SAE ARP 9162 : 2017	AEROSPACE OPERATOR SELF-VERIFICATION PROGRAMS
UNI EN 3537 : 2011	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
ONORM EN 9133 : 2006	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - QUALIFICATION PROCEDURE FOR AEROSPACE STANDARD PARTS
BS EN 3660-001:2016	Aerospace series. Cable outlet accessories for circular and rectangular electrical and optical connectors Technical specification
I.S. EN 2865:2009	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUGS, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
I.S. EN 4800-005:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK
I.S. EN 4811:2017	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH FLUOROCARBON SEAL ON ALUMINIUM PLATE WITH 4 FASTENING HOLES - INCH SERIES
NF EN 2755 : 2010	AEROSPACE SERIES - BEARINGS, SPHERICAL PLAIN IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER - ELEVATED LOAD AT AMBIENT TEMPERATURE - TECHNICAL SPECIFICATION
UNE-EN 9104-001:2013	Aerospace series - Quality management systems - Part 001: Requirements for Aviation, Space, and Defence Quality Management System Certification Programs
NF EN 4800-001 : 2012	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP
I.S. EN 4805:2017	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, STRAIGHT, IN HEAT RESISTING STEEL - INCH SERIES
I.S. EN 2883:2009	AEROSPACE SERIES - NUTS, HEXAGONAL, SELF-LOCKING, WITH COUNTERBORE AND CAPTIVE WASHER, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 9102:2015	AEROSPACE SERIES - QUALITY SYSTEMS - FIRST ARTICLE INSPECTION REQUIREMENTS
NF EN 3834 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUG, INCREMENTAL COUNTERBORE, IN CORROSION RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 9223-103:2018	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 103: CONFIGURATION VERIFICATIONS, REVIEWS AND AUDITS
I.S. EN 4702-04:2017	AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 04: SPRING CLAMP
I.S. EN 6138:2017	AEROSPACE SERIES - CAP, PROTECTIVE, NON-METALLIC FOR FITTING ENDS <= 3000 PSI HYDRAULIC SYSTEMS
I.S. EN 9223-101:2018	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 101: CONFIGURATION IDENTIFICATION
I.S. EN 4800-008:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS
I.S. EN 9136:2018	AEROSPACE SERIES - ROOT CAUSE ANALYSIS AND PROBLEM SOLVING (9S METHODOLOGY)
I.S. EN 4474:2016	AEROSPACE SERIES - ALUMINIUM PIGMENTED COATINGS - COATING METHODS
NF EN 3843 : 2011	AEROSPACE SERIES - NUTS, BIHEXAGONAL, SELF-LOCKING, WITH COUNTERBORE, IN HEAT RESISTING STEEL, PASSIVATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C
I.S. EN 9101:2015	QUALITY MANAGEMENT SYSTEMS - AUDIT REQUIREMENTS FOR AVIATION, SPACE, AND DEFENCE ORGANIZATIONS
EN 16603-31-02:2015	Space engineering - Two-phase heat transport equipment
I.S. EN 16602-20:2014	SPACE PRODUCT ASSURANCE - QUALITY ASSURANCE
BS EN 9104-002:2016	Aerospace series. Quality management systems Requirements for Oversight of Aerospace Quality Management System Registration/Certification Programs
EN 9120:2010	Quality Management Systems - Requirements for Aviation, Space and Defence Distributors
BS EN 9133:2004	Aerospace series. Quality management systems. Qualification procedure for aerospace standard parts
I.S. EN 4801:2017	AEROSPACE SERIES - FLANGE COUPLINGS - SWIVEL FLANGE WITH 3 FASTENING HOLES, IN HEAT RESISTING STEEL - INCH SERIES
EN 9136:2018	Aerospace series - Root cause analysis and problem solving (9S Methodology)
I.S. EN 3660-001:2016	AEROSPACE SERIES - CABLE OUTLET ACCESSORIES FOR CIRCULAR AND RECTANGULAR ELECTRICAL AND OPTICAL CONNECTORS - PART 001: TECHNICAL SPECIFICATION
BS EN 3904:2017	Aerospace series. Washers, wire locking in aluminium alloy, anodized
BS EN 9120:2010	Quality management systems. Requirements for aviation, space and defence distributors
I.S. EN 3753:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 60 DEGREES CORNER, WITH COUNTERBORE, IN ALLOY STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
UNI EN 4700-001 : 2011	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP
SAE AS 9014 : 2015	AMERICAS AEROSPACE QUALITY GROUP (AAQG) REQUIREMENTS FOR AEROSPACE QUALITY MANAGEMENT SYSTEM CERTIFICATION/REGISTRATIONS PROGRAMS
EN 9102:2015	Aerospace series - Quality systems - First article inspection requirements
EN 9110:2015	Quality Management Systems - Requirements for Aviation Maintenance Organizations
EN 4710-01:2015	Aerospace series - Quick release fastening systems for non-structural applications - Part 01: Technical specification
EN 9101:2018	Quality Management Systems - Audit Requirements for Aviation, Space, and Defence Organisations
I.S. EN 2863:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 90 DEGREE CORNER, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
I.S. EN 4136:2009	AEROSPACE SERIES - BOLTS, NORMAL BI-HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
ISO 6517:2013	Air cargo — Certified lower deck containers — Design and testing
EN 4644-001:2017	Aerospace series - Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 °C (or 125 °C) continuous - Part 001: Technical specification
I.S. EN 3226:2009	NUTS, HEXAGON, PLAIN, NORMAL HEIGHT, NORMAL ACROSS FLATS, STEEL, CADMIUM PLATED - CLASSIFICATION 1100 MPA/235 DEGREES C
I.S. EN 4138:2016	AEROSPACE SERIES - SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
ISO 7169:2014	Aerospace Separable tube fittings for fluid systems, for 24 degree cones, for pressures up to 3 000 psi or 21 000 kPa Procurement specification, inch/metric
I.S. EN 9120:2010	QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENCE DISTRIBUTORS
I.S. EN 4700-005:2010	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK
I.S. EN 3538:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 4649:2009	AEROSPACE SERIES - HANDHELD FIRE EXTINGUISHERS WITH SYNTHESIS GASES, FOR AIRCRAFT USE - TECHNICAL SPECIFICATION AND QUALIFICATION CONDITIONS
I.S. EN 3875:2017	AEROSPACE SERIES - METALLIC MATERIALS, FILLER METAL FOR BRAZING - TECHNICAL SPECIFICATION
I.S. EN 4127:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM 4D COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREE C
11/30242263 DC : 0	BS EN 4691-001 - AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - TECHNICAL SPECIFICATION
BS EN 3777:2010	Aerospace series. Pins, quick release, single and double acting. Technical specification
BS EN 4590:2005	Aerospace series. Retainers, spring, sheet metal, for self-locking barrel nuts, in corrosion resisting steel, passivated
BS EN 9121:2009	Aerospace series. Quality management systems. Assessment applicable to stockist distributors
BS EN 2491:2011	Aerospace series. Molybdenum disulphide dry lubricants. Coating methods
BS EN 3867:2004	Aerospace series. Pipe couplings, loose flanges and seals. Flanges in titanium alloy TI-P64001
BS EN 9102:2015	Aerospace series. Quality systems. First article inspection requirements
BS EN 2680:2006	Aerospace series. Nuts, anchor, self-locking, floating, self-aligning, two lug, in alloy steel, cadmium plated, MoS<sub>2</sub> lubricated. Classification: 900 MPa (at ambient temperature) / 235°C
BS EN 3868:2004	Aerospace series. Pipe couplings, loose flanges and seals. Flange connectors, welded, in titanium alloy TI-P64001
UNE-EN 9121:2011	Aerospace series - Quality management systems - Assessment applicable to stockist distributors (based on ISO 9001:2000)
BS EN 3820:2017	Aerospace series. Metric bolts, normal hexagon head, coarse tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated. Classification: 1 100 MPa (at ambient temperature)/315 °C
BS EN 4509:2006	Screws, 100° countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, with aluminium pigmented coating, metric series. Classification: 1100 MPa (at ambient temperature)/315°C
BS EN 3280:2011	Aerospace series. Bearings, airframe rolling, rigid or self-aligning. Technical specification
BS EN 2881:2006	Aerospace series. Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS<sub>2</sub> lubricated. Classification: 900 MPa (at ambient temperature) / 120°C
EN 16602-20:2014	Space product assurance - Quality assurance
BS EN 9200:2004	Programme management. Guidelines for project management specification
BS EN 4425:2006	Aerospace series. Washers, tab in corrosion resisting steel for flight control rods. Dimensions
BS EN 4496:2005	Aerospace series. Screws, 100° countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating. Classification: 1100 MPa (at ambient temperature) / 315 °C
BS EN 4591:2005	Aerospace series. Nuts, barrel, self-locking, floating, self-aligning,in heat resisting nickel base alloy, MoS<sub>2</sub> lubricated. Classification: 15 50 MPa (at ambient temperature) / 315°C
BS EN 4415:2006	Aerospace series. Non-metallic materials. Textiles. Narrow woven fabrics. Technical specification
BS EN 4115:2010	Aerospace series. Cushion, rubber for clamps. Dimensions, masses
BS EN 2856:2006	Aerospace series. Nuts, anchor, self-locking, fixed, closed corner, reduced series, with counterbore. Classification: 1100 MPa/235°C
BS EN 4416:2006	Aerospace series. Non-metallic materials. Textiles. Wide woven fabrics. Technical specification
BS EN 2596:2006	Aerospace series. Washers, lock, with radial serrations in corrosion resisting steel, cadmium plated for flight control rods. Dimensions
PD IEC/TS 62668-2:2016	Process management for avionics. Counterfeit prevention Managing electronic components from non-franchised sources
BS EN 9111:2005	Aerospace series. Quality management systems. Assessment applicable to maintenance organizations
BS EN 4495:2006	Aerospace series. Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating, metric series. Classification: 1100 MPa (at ambient temperature) / 315°C
BS EN 2133:2010	Aerospace series. Cadmium plating of steels with specified tensile strength ≤ 1450 MPa, copper, copper alloys and nickel alloys
BS EN 4074:2009	Aerospace series. Screws, pan head, six lobe recess, coarse tolerance normal shank, medium length thread, in titanium alloy, aluminium IVD coated. Classification: 1100 MPa (at ambient temperature)/425°C
BS EN 4501:2006	Aerospace series. Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating, metric series. Classification: 1100 MPa (at ambient temperature) / 315°C
09/30204364 DC : 0	BS EN 6104 - AEROSPACE SERIES - RIVETS, SOLID, IN ALUMINIUM OR ALUMINIUM ALLOY - INCH SERIES - TECHNICAL SPECIFICATION
BS EN 2549:2006	Aerospace series. Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium, anodized, MoS<sub>2</sub> lubricated. Classification: 1100 MPa (at ambient temperature) / 315°C
BS EN 4691-1:2017	Aerospace series. Tie rod with integrated bolts Technical specification
BS EN 9104:2006	Aerospace series. Quality management systems. Requirements for aerospace quality management system certification/ registrations programs
EN 9121:2009	Aerospace series - Quality management systems - Assessment applicable to stockist distributors (based on ISO 9001:2000)
EN 4135:2009	Aerospace series - Bolts, normal bi-hexagonal head, coarse tolerance normal shank, medium length thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4075:2008	Aerospace series - Screws, pan head, offset cruciform recess, threaded to head, in corrosion resisting steel, passivated - Classification: 490 MPa (at ambient temperature) / 425 °C
EN 4800-003:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 003: Tube
EN 4591:2005	Aerospace series - Nuts, barrel, self-locking, floating, self-aligning, in heat resisting nickel base alloy, MoS2 lubricated - Classification: 1 550 MPa (at ambient temperature) / 315 °C
EN 3712:2007	Aerospace series - Nuts, anchor, self-locking, one lug, fixed, reduced series, with counterbore, in steel, cadmium plated, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 3820:2017	Aerospace series - Metric bolts, normal hexagon head, coarse tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature)/315 °C
EN 4494:2006	Aerospace series - Rings, split, in stainless steel
EN 16602-20-07:2016	Space product assurance - Quality and safety assurance for space test centres
EN 2754:2006	Aerospace series - Nuts, anchor, self locking, two lug, floating with counterbore - Classification: 1 100 MPa/235 °C
EN 4495:2006	Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating, metric series - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4817:2012	Aerospace series - Passive UHF RFID tags intended for aircraft use
EN 4800-002:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 002: Bar and section
EN 2786:2008	Aerospace series - Electrolytic silver plating of fasteners
EN 3626:2006	Aerospace series - Nuts, hexagon, self-locking in steel, cadmium plated, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature)/235 °C
EN 3908:2017	Aerospace series - Nipples, lubricating, axial type, in corrosion resisting steel, passivated
EN 4810:2017	Aerospace series - Flange couplings - Gasket seal with nickel alloy C seal on heat resisting steel plate with 3 fastening holes - Inch series
EN 4073:2016	Aerospace series - Screws, pan head, hexalobular recess, coarse tolerance shank, medium length thread, in alloy steel, cadmium plated - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 4800-001:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 001: Plate, sheet and strip
EN 3843:2010	Aerospace series - Nuts, bihexagonal, self-locking, with counterbore, in heat resisting steel, passivated - Classification: 1 100 MPa (at ambient temperature) / 650 °C
EN 4166:2004	Aerospace series - Clips, spring tension, three parts - PTFE bushes
EN 4498:2005	Aerospace series - Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated, with aluminium pigmented coating - Classification: 1 550 MPa (at ambient temperature) / 315 °C
EN 4125:2010	Aerospace series - Nuts, anchor, self-locking, fixed, two lug, reduced series, with incremental counterbore, in heat resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 315 °C
EN 4416:2006	Aerospace series - Non-metallic materials - Textiles - Wide woven fabrics - Technical specification
EN 4415:2006	Aerospace series - Non-metallic materials - Textiles - Narrow woven fabrics - Technical specification
EN 4126:2010	Aerospace series - Nuts, anchor, self-locking, floating, two lug, reduced series, with incremental counterbore, in heat resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 315 °C
EN 4132:2009	Aerospace series - Bolts, normal hexagonal head, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 4700-005:2010	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 005: Forging stock
EN 2596:2006	Aerospace series - Washers, lock, with radial serrations in corrosion resisting steel, cadmium plated for flight control rods - Dimensions
EN 4697:2016	Aerospace series - General and installation requirements for passenger seat fittings
EN 4811:2017	Aerospace series - Flange couplings - Gasket seal with fluorocarbon seal on aluminium plate with 4 fastening holes - Inch series
EN 3537:2010	Aerospace series - Nuts, anchor, self-locking, fixed, two lug, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature)/315 °C
EN 3727:2006	Aerospace series - Bearings, airframe rolling rigid with flanged alignment housing - Technical specification
EN 9104-002:2016	Aerospace series - Quality management systems - Part 002: Requirements for Oversight of Aerospace Quality Management System Registration/Certification Programs
EN 4074:2009	Aerospace series - Screws, pan head, six lobe recess, coarse tolerance normal shank, medium length thread, in titanium alloy, aluminium IVD coated - Classification: 1 100 MPa (at ambient temperature) / 425 °C
EN 3902:2016	Aerospace series - Washers for rivet assemblies, in aluminium alloy, anodized, metric series
EN 3777:2010	Aerospace series - Pins, quick release, single and double acting - Technical specification
EN 4133:2009	Aerospace series - Bolts, normal hexagonal head, coarse tolerance normal shank, long thread, in titanium alloy, aluminium IVD coated - Classification: 1 100 MPa (at ambient temperature) / 425 °C
EN 2337:2006	Aerospace series - Spherical plain bearings - Technical specification
EN 4700-003:2010	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 003: Tube
EN 3228:2010	Aerospace series - Nuts, hexagonal, plain, reduced height, normal across flats, in steel, cadmium plated - Classification: 900 MPa (at ambient temperature) / 235 °C
EN 3431:2007	Aerospace series - Nuts, hexagonal, self-locking, with counterbore and captive washer, in heat resisting steel, silver plated - Classification: 1 100 MPa (at ambient temperature) / 425 °C
EN 2549:2006	Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated, metric series - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 3229:2009	Aerospace series - Nuts, hexagonal, plain, reduced height, normal across flats, in steel, cadmium plated, left hand thread - Classification: 900 MPa (at ambient temperature) / 235 °C
EN 9104:2006	Aerospace series - Quality management systems - Requirements for Aerospace Quality Management System Certification/Registrations Programs
EN 2862:2009	Aerospace series - Nuts, anchor, self-locking, fixed, 90° corner, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated - Classification : 1 100 MPa (at ambient temperature) / 235 °C
EN 4803:2017	Aerospace series - Flange couplings - Swivel flange with 4 fastening holes, in heat resisting steel - Inch series
EN 4084:2009	Aerospace series - Nuts, anchor, self-locking, fixed, two lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated - Classification: 1 100 MPA (at ambient temperature) / 235 °C
EN 4499:2009	Aerospace series - Screws, 100° countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4636:2009	Aerospace series - Screws, 100° countersunk head, six lobe recess, short thread, in titanium alloy TI-P64001, with aluminium pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4309:2016	Aerospace series - Nuts, hexagon, self-locking by plastic ring, normal height, normal across flats, in alloy steel, cadmium plated - Classification: 900 MPa (at ambient temperature) / 120 °C
EN 9111:2005	Aerospace series - Quality management systems - Assessment applicable to maintenance organizations (based on ISO 9001:2000)
EN 2866:2009	Aerospace series - Nuts, anchor, self-locking, floating, one lug, with counterbore, in steel, cadmium plated, MoS2 lubricated - Classification: 1 110 MPa (at ambient temperature) / 235 °C
EN 4425:2006	Aerospace series - Washers, tab in corrosion resisting steel for flight control rods - Dimensions
EN 4819:2012	Aerospace series - Contact Memory Button (CMB) tags intended for aircraft use
EN 4115:2010	Aerospace series - Cushion, rubber for clamps - Dimensions, masses
EN 9104-003:2010	Aerospace series - Quality management systems - Part 003: Requirements for Aerospace Quality Management System (AQMS) Auditor Training and Qualification
EN 3763:2010	Aerospace series - Nuts, hexagonal, self-locking, ball seat, in heat resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 315 °C
EN 3538:2010	Aerospace series - Nuts, anchor, self-locking, fixed, two lug, reduced series, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature)/315 °C
EN 3757:2009	Aerospace series - Nuts, anchor, self-locking, floating, self-aligning, two lugs, in heat resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 315 °C
EN 2865:2009	Aerospace series - Nuts, anchor, self-locking, floating, two lugs, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4590:2005	Aerospace series - Retainers, spring, sheet metal, for self-locking barrel nuts, in corrosion resisting steel, passivated
EN 3834:2010	Aerospace series - Nuts, anchor, self-locking, floating, two lug, incremental counterbore, in corrosion resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 315 °C
EN 3868:2004	Aerospace series - Pipe couplings, loose flanges and seals - Flange connectors, welded, in titanium alloy TI-P64001
EN 4312:2006	Aerospace series - Studs, coarse tolerance reduced shank, medium length thread, in heat and corrosion resisting steel, with aluminium pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4700-007:2010	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 007: Remelting stock
EN 3840:2007	Aerospace series - Paints and varnishes - Technical specification
EN 2879:2017	Aerospace series - Nuts, anchor, self-locking, air resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 235 °C
EN 4178:2017	Aerospace series - Screws, pan head, six lobe recess, coarse tolerance normal shank, medium length thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4501:2006	Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating, metric series - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 9116:2015	Aerospace series - Notice of Change (NOC) Requirements
EN 4297:2017	Aerospace series - Nuts, hexagon, self-locking by plastic ring, normal height, normal across flats, in corrosion resisting steel, passivated - Classification: 900 MPa (at ambient temperature) / 120 °C
EN 2043:2013	Aerospace series - Metallic materials - General requirements for semi-finished product qualification (excluding forgings and castings)
EN 4071:2009	Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated - Classification: 1 100 MPa (at ambient temperature) / 425 °C
EN 3280:2011	Aerospace series - Bearings, airframe rolling, rigid or self-aligning - Technical specification
EN 4128:2016	Aerospace series - Bolts, normal hexagonal head, coarse tolerance shank, short thread, in heat resisting nickel base alloy, aluminium IVD coated - Classification: 1 250 MPa (at ambient temperature) / 425 °C
EN 4311:2006	Aerospace series - Studs, coarse tolerance reduced shank, medium length threads, in heat and corrosion resisting steel, MoS2 lubricated - Classification : 1 100 MPa (at ambient temperature) / 315 °C
EN 3539:2010	Aerospace series - Nuts, anchor, self-locking, one lug, fixed, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 2863:2010	Aerospace series - Nuts, anchor, self-locking, fixed, 90° corner, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4137:2009	Aerospace series - Bolts, normal bi-hexagonal head, stepped shank, long thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 9137:2012	Quality management systems - Guidance for the Application of AQAP 2110 within an EN 9100 Quality Management System
EN 4163:2016	Aerospace series - Screws 100° countersunk normal head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 3660-001:2016	Aerospace series - Cable outlet accessories for circular and rectangular electrical and optical connectors - Part 001: Technical specification
EN 2881:2006	Aerospace series - Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS2 lubricated, metric series - Classification: 900 MPa (at ambient temperature) / 120 °C
EN 4813:2017	Aerospace series - Flange couplings - Cap, in heat resisting steel - Inch series
EN 4800-004:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 004: Wire
EN 2859:2006	Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in alloy steel, cadmium plated, metric series - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 3631:2014	Aerospace series - Fluid fittings, flanged, 90° elbowed - Sealing by O-ring for 0,8 mm thick tubes
EN 3444:2006	Aerospace series - Bolt, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated - Classification: 1 250 MPa (at ambient temperature) /650 C
EN 4804:2017	Aerospace series - Flange couplings - Swivel flange with 4 fastening holes, in nickel alloy - Inch series
EN 3052:2009	Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in heat and corrosion resisting steel, passivated - Classification: 1 100 MPa (at ambient temperature) / 425 °C
EN 2882:2006	Aerospace series - Nuts, hexagonal, self-locking, with counterbore and captive washer, in steel, cadmium plated, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 3867:2004	Aerospace series - Pipe couplings, loose flanges and seals - Flanges in titanium alloy TI-P64001
EN 3753:2010	Aerospace series - Nuts, anchor, self-locking, fixed, 60° corner, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 3227:2010	Aerospace series - Nuts, hexagonal, plain, normal height, normal across flats, in steel, cadmium plated, left hand thread - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 4818:2012	Aerospace series - Passive HF RFID tags intended for aircraft use
EN 2535:2011	Aerospace series - Vacuum deposition of cadmium
EN 9117:2017	Aerospace series - Delegated Product Release Verification
EN 6138:2017	Aerospace series - Cap, protective, non-metallic for fitting ends ≤ 3 000 PSI hydraulic systems
EN 4800-006:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 006: Pre-production and production forgings
EN 4808:2017	Aerospace series - Flange couplings - Weld coupling, 90° elbow, in nickel alloy - Inch series
EN 4729:2017	Aerospace series - Trivalent chromium based chemical conversion coatings for aluminium and aluminium alloys
EN 4807:2017	Aerospace series - Flange couplings - Weld coupling, 90° elbow, in heat resisting steel - Inch series
EN 3903:2017	Aerospace series - Washers, laminated, in corrosion resisting steel
EN 3768:2012	Aerospace series - Nuts, anchor, self-locking, one lug, fixed, reduced series, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature)/315 °C
EN 4127:2009	Aerospace series - Bolts, normal hexagonal head, coarse tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated - Classification: 1 100 MPa (at ambient temperature) / 425 °C
EN 3536:2006	Aerospace series - Nuts, hexagon, self-locking, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature)/315 °C
EN 2491:2011	Aerospace series - Molybdenum disulphide dry lubricants - Coating methods
EN 2811:2016	Aerospace series - Nuts, hexagon, slotted/ castellated in steel cadmium plated - Classification: 1 100 MPa/235 °C
EN 4138:2016	Aerospace series - Screws, pan head, offset cruciform recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated - Classification: 1 100 MPa (at ambient temperature) / 235 °C
EN 4800-008:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 008: Pre-production and production castings
EN 3653:2010	Aerospace series - Nuts, anchor, self-locking, floating, self-aligning, one lug, in steel, cadmium plated, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 235 °C
EN 2852:2010	Aerospace series - Nuts, hexagonal, plain, normal height, normal across flats, heat resisting steel passivated - Classification: 1 100 MPa/650 °C
EN 3750:2010	Aerospace series - Nuts, anchor, self-locking, fixed, 90° corner, reduced series, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 2867:2009	Aerospace series - Nuts, anchor, self-locking, floating, one lug, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4167:2004	Aerospace series - Clips, spring tension, three parts - Inner clips in heat resisting steel FE-PA2601 (A286)
EN 3388:2009	Aerospace series - Fasteners, externally threaded, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification 1 275 MPa/650 °C - Manufacturing method optional - Technical specification
EN 4800-007:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 007: Remelting stock
EN 4809:2017	Aerospace series - Flange couplings - Gasket seal with fluorocarbon seal on aluminium plate with 3 fastening holes - Inch series
EN 4134:2009	Aerospace series - Bolts, normal hexagonal head, coarse tolerance normal shank, long thread, in heat resisting nickel base alloy, aluminium IVD coated - Classification: 1 250 MPa (at ambient temperature) / 425°C
EN 9200:2004	Aerospace series - Programme management - Guidelines for project management specification
EN 2888:2006	Aerospace series - Metric Bolts, normal hexagon head, coarse tolerance normal shank, short thread, in corrosion resisting steel, passivated - Classification: 600 MPa (at ambient temperature)/425 °C
EN 4168:2004	Aerospace series - Clips, spring tension, three parts - Outer clips in heat resisting steel FE-PA2601 (A286)
EN 4509:2006	Aerospace series - Screws, 100 countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, with aluminium pigmented coating, metric series - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 4106:2013	Aerospace series - Non-metallic materials - Structural adhesive systems - Paste adhesive - Technical specification
EN 4800-005:2010	Aerospace series - Titanium and titanium alloys - Technical specification - Part 005: Forging stock
EN 4700-004:2010	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 004: Wire
EN 3302:2017	Aerospace series - Bolts in heat resisting steel FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Technical specification
EN 4700-001:2010	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 001: Plate, sheet and strip
EN 4826:2014	Aerospace series - Zinc-Nickel (12 %-16 % Ni) plating of steels with specified tensile strength ≤ 1 450 MPa, copper alloys, nickel alloys and aluminium alloys for parts and fasteners
EN 2883:2009	Aerospace series - Nuts, hexagonal, self-locking, with counterbore and captive washer, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 2680:2006	Aerospace series - Nuts, anchor, self-locking, floating, self-aligning, two lug, in alloy steel, cadmium plated, MoS2 lubricated, metric series - Classification: 900 MPa (at ambient temperature) / 235 °C
EN 4700-006:2010	Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 006: Pre-production and production forgings
EN 2311:2017	Aerospace series - Bushes with self-lubricating liner - Technical specification
EN 3435:2010	Aerospace series - Nuts, anchor, self-locking, floating, two lug, reduced series, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 2856:2006	Aerospace series - Nuts, anchor, self-locking, fixed, closed corner, reduced series, with counterbore - Classification: 1 100 MPa/235 °C
EN 3226:2009	Aerospace series - Nuts, hexagon, plain, normal height, normal across flats, steel, cadmium plated - Classification 1 100 MPa/235 °C
EN 4802:2017	Aerospace series - Flange couplings - Swivel flange with 3 fastening holes, in nickel alloy - Inch series
EN 3389:2009	Aerospace series - Fasteners, externally threaded, in heat resisting nickel base alloy NI-PH1302 (Waspaloy) - Classification: 1 210 MPa/730 °C - Manufacturing method optional - Technical specification
EN 4649:2009	Aerospace series - Handheld fire extinguishers with synthesis gases, for aircraft use - Technical specification and qualification conditions
EN 4812:2017	Aerospace series - Flange couplings - Gasket seal with nickel alloy C seal on heat resisting steel plate with 4 fastening holes - Inch series
BS EN 4700-001:2010	Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Plate, sheet and strip
05/30128217 DC : DRAFT JAN 2005	ISO/DIS 23933 - AEROSPACE - ARAMID REINFORCED LIGHTWEIGHT POLYTETRAFLUOROETHYLENE (PTFE) HOSE ASSEMBLIES, CLASSIFICATION 135 DEGREE C/20 684 KPA (275 DEGREE F/3 000 PSI) AND 135 DEGREE C/21 000 KPA (275 DEGREE F/3 046 PSI) - PROCUREMENT SPECIFICATION
UNI EN 9115 : 2013	QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE ORGANIZATIONS - DELIVERABLE SOFTWARE (SUPPLEMENT TO EN 9100)
NF EN 3435 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUG, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
UNE-EN 9104-003:2011	Aerospace series - Quality management systems - Part 003: Requirements for Aerospace Quality Management System (AQMS) Auditor Training and Qualification
13/30288693 DC : 0	BS EN 4138 - AEROSPACE SERIES- SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
BS EN 4132:2009	Aerospace series. Bolts, normal hexagonal head, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature)/235°C
I.S. EN 3537:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, TWO LUG, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS EN 2811:2016	Aerospace series. Nuts, hexagon, slotted/castellated in steel cadmium plated. Classification. 1 100 MPa/235 °C
01/708064 DC : DRAFT MAY 2001	PREN AECMA 8.6013 - AEROSPACE SERIES - QUALIFICATION PROCEDURE FOR AEROSPACE PRODUCTS
UNE-EN 9131:2016	Aerospace series - Quality Management Systems - Nonconformance Data Definition and Documentation
BS EN 4801:2017	Aerospace series. Flange couplings. Swivel flange with 3 fastening holes, in heat resisting steel. Inch series
I.S. EN 4819:2012	AEROSPACE SERIES - CONTACT MEMORY BUTTON (CMB) TAGS INTENDED FOR AIRCRAFT USE
BS EN 9116:2015	Aerospace series. Notice of Change (NOC) Requirements
I.S. EN 4161:2009	AEROSPACE SERIES - SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
BS EN 2852:2010	Aerospace series. Nuts, hexagonal, plain, normal height, normal across flats, heat resisting steel passivated. Classification: 1100 MPa/650°C
I.S. EN 9104:2006	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AEROSPACE QUALITY MANAGEMENT SYSTEM CERTIFICATION/REGISTRATIONS PROGRAMS
SAE AS 9121 : 2012	STOCKIST DISTRIBUTORS QUALITY SYSTEM QUESTIONNAIRE ASSOCIATED WITH AS9120
BS EN 4071:2009	Aerospace series. Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated. Classification: 1100 MPa (at ambient temperature) / 425 °C
UNI EN 2535 : 2012	AEROSPACE SERIES - VACUUM DEPOSITION OF CADMIUM
BS EN 3834:2010	Aerospace series. Nuts, anchor, self-locking, floating, two lug, incremental counterbore, in corrosion resisting steel, MoS2 lubricated. Classification: 900 MPa (at ambient temperature)/315°C
UNE-EN 9110:2015	Quality Management Systems - Requirements for Aviation Maintenance Organizations
I.S. EN 3903:2017	AEROSPACE SERIES - WASHERS, LAMINATED, IN CORROSION RESISTING STEEL
12/30260908 DC : 0	BS EN 4713 - AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, CONTINUOUS FIBRE REINFORCED PEEK COMPOSITE, TEMPERATURE RANGE -65 DEGREES C TO 135 DEGREES C - INCH SERIES
BS EN 3908:2017	Aerospace series. Nipples, lubricating, axial type, in corrosion resisting steel, passivated
EN 3904:2017	Aerospace series - Washers, wire locking in aluminium alloy, anodized
I.S. EN 4700-003:2010	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 003: TUBE
11/30247470 DC : DRAFT MAY 2011	BS EN 4710-001 - AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - TECHNICAL SPECIFICATION
BS EN 2862:2009	Aerospace series. Nuts, anchor, self-locking, fixed, 90° corner, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/235°C
BS EN 2866:2009	Aerospace series. Nuts, anchor, self-locking, floating, one lug, with counterbore, in steel, cadmium plated, MoS2 lubricated. Classification: 1110 MPa (at ambient temperature)/235°C
BS EN 2883:2009	Aerospace series. Nuts, hexagonal, self-locking, with counterbore and captive washer, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature)/315°C
17/30362517 DC : DRAFT JUNE 2017	BS EN 4234 - AEROSPACE SERIES - CLAMPS, WORM DRIVE - DIMENSIONS, MASSES
BS EN 4700-007:2010	Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Remelting stock
I.S. EN 4800-003:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 003: TUBE
13/30288691 DC : 0	BS EN 4071 - AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, CLOSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
SAE AS 9146 : 2017	FOREIGN OBJECT DAMAGE (FOD) PREVENTION PROGRAM - REQUIREMENTS FOR AVIATION, SPACE, AND DEFENSE ORGANIZATIONS
RG.AERO 00076 : 0	PROGRAMME MANAGEMENT - RECOMMENDATIONS FOR THE IMPLEMENTATION OF THE INTEGRATED LOGISTIC SUPPORT
I.S. EN 2867:2009	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, ONE LUG, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
BS EN 4800-007:2010	Aerospace series. Titanium and titanium alloys Remelting stock
16/30336277 DC : 0	BS EN 9101 - QUALITY MANAGEMENT SYSTEMS - AUDIT REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE ORGANIZATIONS
14/30301637 DC : 0	BS EN 9117 - AEROSPACE SERIES - DELEGATED PRODUCT RELEASE VERIFICATION
BS EN 4809:2017	Aerospace series. Flange couplings. Gasket seal with fluorocarbon seal on aluminium plate with 3 fastening holes. Inch series
BS EN 3840:2007	Aerospace series. Paints and varnishes. Technical specification
BS EN 3902:2016	Aerospace series. Washers for rivet assemblies, in aluminium alloy, anodized, metric series
I.S. EN 4800-007:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK
NF EN 2869 : 2010	AEROSPACE SERIES - NUTS, HEXAGONAL, SLOTTED/CASTELLATED, NORMAL HEIGHT, NORMAL ACROSS FLATS, IN HEAT RESISTING STEEL, PASSIVATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C
PREN 4178 : 200P2	AEROSPACE SERIES - SCREWS, PAN HEAD, SIX LOBE RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
PREN 4868 : DRAFT 2018	AEROSPACE SERIES - ANODIC ELECTRODEPOSITION OF HEXAVALENT CHROMIUM FREE PRIMER
NF EN 3757 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, SELF-ALIGNING, TWO LUGS, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
BS 2A 293:2005	Procurement of self-locking nuts with non-metallic locking elements. Metric series. Specification
PREN 4636 : 200P1	AEROSPACE SERIES - SCREWS, 100 DEGREE COUNTERSUNK HEAD, SIX LOBE RECESS, SHORT THREAD, IN TITANIUM ALLOY TI-P64001, WITH ALUMINIUM PIGMENTED COATING - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
PREN 4833 : DRAFT 2017	AEROSPACE SERIES - PIPE COUPLING 24 DEGREES CONE UP TO 35000 KPA (5080 PSI) RING LOCKED FITTING - FLARELESS END - INCH SERIES - EXTRA FINE THREAD PITCH
I.S. EN 4128:2016	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE SHANK, SHORT THREAD, IN HEAT RESISTING NICKEL BASE ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1250 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
XP PREN 9102 : 2005 XP	AEROSPACE SERIES - QUALITY SYSTEMS - FIRST ARTICLE INSPECTION
I.S. EN 4817:2012	AEROSPACE SERIES - PASSIVE UHF RFID TAGS INTENDED FOR AIRCRAFT USE
PREN 9223-102 : DRAFT 2016	PROGRAMME MANAGEMENT - CONFIGURATION MANAGEMENT - PART 102: CONFIGURATION STATUS ACCOUNTING
PREN 9146 : DRAFT 2017	FOREIGN OBJECT DAMAGE (FOD) PREVENTION PROGRAM - REQUIREMENTS FOR AVIATION, SPACE, AND DEFENCE ORGANIZATIONS
PREN 4836 : DRAFT 2017	AEROSPACE SERIES - ADAPTOR, PIPE COUPLING 24 DEGREES CONE UP TO 35000 KPA (5080 PSI) RING-LOCKED FITTING REDUCER - FLARELESS END - INCH SERIES - EXTRA FINE THREAD PITCH
PREN 4854-1 : 200P1	AEROSPACE SERIES - BEARING, SPHERICAL PLAIN, IN CORROSION RESISTING STEEL WITH SELF-LUBRICATING LINER, LOW STARTING TORQUE AND LOW FRICTION COEFFICIENT, ELEVATED DUTY CYCLES UNDER LOW OSCILLATIONS AT DIFFERENT OPERATING CONDITIONS - PART 1: DIMENSIONS AND LOADS FOR NARROW SERIES
PREN 9117 : DRAFT 2016	AEROSPACE SERIES - DELEGATED PRODUCT RELEASE VERIFICATION
PREN 2491 : 200P1	AEROSPACE SERIES - MOLYBDENUM DISULPHIDE DRY LUBRICANTS - COATING METHODS
NF EN 3753 : 2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 60 DEGREES CORNER, WITH COUNTERBORE, IN ALLOY STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
PREN 9120 : 200P4	QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENCE DISTRIBUTORS
PREN 9111 : 200P2	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - ASSESSMENT APPLICABLE TO MAINTENANCE ORGANIZATIONS
PREN 9103 : 200P2	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - VARIATION MANAGEMENT OF KEY CHARACTERISTICS
PREN 9134 : 200P1	AEROSPACE SERIES - QUALITY SYSTEMS - SUPPLY CHAIN RISK MANAGEMENT GUIDELINE
16/30352063 DC : 0	BS EN 16603-31-02 - SPACE ENGINEERING - TWO-PHASE HEAT TRANSPORT EQUIPMENT
PREN 4807 : DRAFT 2015	AEROSPACE SERIES - FLANGE COUPLINGS - WELD COUPLING, 90 DEGREES ELBOW, IN HEAT RESISTING STEEL - INCH SERIES
PREN 4800-007 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 7: REMELTING STOCK
SAE AS 9116 : 2014	AEROSPACE SERIES - NOTICE OF CHANGE (NOC) REQUIREMENTS
PREN 9104-001 : 200P1	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - PART 001: REQUIREMENTS FOR AVIATION, SPACE AND DEFENCE QUALITY MANAGEMENT SYSTEM CERTIFICATION PROGRAMS
PREN 3820 : 200P3	AEROSPACE SERIES - METRIC BOLTS, NORMAL HEXAGON HEAD, COARSE TOLERANCE NORMAL SHANK, SHORT THREAD, IN TITANIUM ALLOY, ANODIZED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
PREN 4700-007 : 200P2	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK
ISO 23933:2006	Aerospace Aramid reinforced lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 135 degrees C/20 684 kPa (275 degrees F /3 000 psi) and 135 degrees C/21 000 kPa (275 degrees F/3 046 psi) Procurement specification
PREN 4800-004 : 200P2	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 4: WIRE
PREN 4700-001 : 200P2	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP
PREN 4115 : 200P2	AEROSPACE SERIES - CUSHION, RUBBER FOR CLAMPS - DIMENSIONS, MASSES
PREN 4700-002 : 200P3	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION
PREN 9115 : 200P1	QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE ORGANIZATIONS - DELIVERABLE SOFTWARE (SUPPLEMENT TO EN 9100)
I.S. EN 4126:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUG, REDUCED SERIES, WITH INCREMENTAL COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 3768:2012	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, ONE LUG, FIXED, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
UNI EN 4800-002 : 2011	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION
I.S. EN 4133:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN TITANIUM ALLOY, ALUMINIUM IVD COATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/425 DEGREES C
I.S. EN 3389:2009	AEROSPACE SERIES - FASTENERS, EXTERNALLY THREADED, IN HEAT RESISTING NICKEL BASE ALLOY NI-PH1302 (WASPALOY) - CLASSIFICATION: 1210 MPA/730 DEGREE C - MANUFACTURING METHOD OPTIONAL - TECHNICAL SPECIFICATION
BS EN 4710-01:2015	Aerospace series. Quick release fastening systems for non-structural applications Technical specification
I.S. EN 4813:2017	AEROSPACE SERIES - FLANGE COUPLINGS - CAP, IN HEAT RESISTING STEEL - INCH SERIES
I.S. EN 4810:2017	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH NICKEL ALLOY C SEAL ON HEAT RESISTING STEEL PLATE WITH 3 FASTENING HOLES - INCH SERIES
I.S. EN 4163:2016	AEROSPACE SERIES - SCREWS 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 3750:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FIXED, 90 DEGREES CORNER, REDUCED SERIES, WITH COUNTERBORE, IN HEAT RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 4800-001:2010	AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP
NF EN 4161 : 2010	AEROSPACE SERIES - SCREWS, PAN HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, LONG THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 4636:2009	AEROSPACE SERIES - SCREWS, 100 DEGREE COUNTERSUNK HEAD, SIX LOBE RECESS, SHORT THREAD, IN TITANIUM ALLOY TI-P64001, WITH ALUMINIUM PIGMENTED COATING - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/315 DEGREE C
I.S. EN 4710-01:2015	AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 01: TECHNICAL SPECIFICATION
ISO 8913:2006	Aerospace Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 400 degrees F/3 000 psi (204 degrees C/20 684 kPa) and 204 degrees C/21 000 kPa (400 degrees F/3 046 psi) Procurement specification
I.S. EN 3834:2010	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, FLOATING, TWO LUG, INCREMENTAL COUNTERBORE, IN CORROSION RESISTING STEEL, MOS[2] LUBRICATED - CLASSIFICATION: 900 MPA (AT AMBIENT TEMPERATURE)/315 DEGREES C
I.S. EN 2811:2016	AEROSPACE SERIES - NUTS, HEXAGON, SLOTTED/CASTELLATED IN STEEL CADMIUM PLATED - CLASSIFICATION: 1100 MPA/235 DEGREES C
UNE-EN 9101:2016	Quality Management Systems - Audit Requirements for Aviation, Space, and Defence Organisations
AQAP 2310 : 2017	NATO QUALITY ASSURANCE REQUIREMENTS FOR AVIATION, SPACE AND DEFENCE SUPPLIERS
I.S. EN 4700-004:2010	AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 004: WIRE
I.S. EN 4106:2013	AEROSPACE SERIES - NON-METALLIC MATERIALS - STRUCTURAL ADHESIVE SYSTEMS - PASTE ADHESIVE - TECHNICAL SPECIFICATION
I.S. EN 4129:2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
SAE AS 9102 : 2014	AEROSPACE FIRST ARTICLE INSPECTION REQUIREMENT
I.S. EN 3902:2016	AEROSPACE SERIES - WASHERS FOR RIVET ASSEMBLIES, IN ALUMINIUM ALLOY, ANODIZED, METRIC SERIES
I.S. EN 4162:2016	AEROSPACE SERIES - SCREWS 100 DEGREES COUNTERSUNK NORMAL HEAD, OFFSET CRUCIFORM RECESS, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
I.S. EN 9104-001:2013	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - PART 001: REQUIREMENTS FOR AVIATION, SPACE, AND DEFENCE QUALITY MANAGEMENT SYSTEM CERTIFICATION PROGRAMS
UNI EN 9104-001 : 2013	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - PART 001: REQUIREMENTS FOR AVIATION, SPACE, AND DEFENCE QUALITY MANAGEMENT SYSTEM CERTIFICATION PROGRAMS
NF EN 4129 : 2009	AEROSPACE SERIES - BOLTS, NORMAL HEXAGONAL HEAD, COARSE TOLERANCE NORMAL SHANK, MEDIUM LENGTH THREAD, IN ALLOY STEEL, CADMIUM PLATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
NF EN 2535 : 2012	AEROSPACE SERIES - VACUUM DEPOSITION OF CADMIUM
I.S. EN 3712:2007	AEROSPACE SERIES - NUTS, ANCHOR, SELF-LOCKING, ONE LUG, FIXED, REDUCED SERIES, WITH COUNTERBORE, IN STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREES C
EN 9223-104:2018	Programme Management - Configuration Management - Part 104: Configuration Control
EN 9223-103:2018	Programme Management - Configuration Management - Part 103: Configuration Verifications, Reviews and Audits
I.S. EN 4812:2017	AEROSPACE SERIES - FLANGE COUPLINGS - GASKET SEAL WITH NICKEL ALLOY C SEAL ON HEAT RESISTING STEEL PLATE WITH 4 FASTENING HOLES - INCH SERIES
UNI EN 9137 : 2012	QUALITY MANAGEMENT SYSTEMS - GUIDANCE FOR THE APPLICATION OF AQAP 2110 WITHIN AN EN 9100 QUALITY MANAGEMENT SYSTEM
UNE-EN 9137:2012	Quality management systems - Guidance for the Application of AQAP 2110 within an EN 9100 Quality Management System
EN 9115:2013	Quality Management Systems - Requirements for Aviation, Space and Defense Organizations - Deliverable Software (Supplement to EN 9100)
EN 4474:2016	Aerospace series - Aluminium pigmented coatings - Coating methods
BS EN 9110:2015	Quality Management Systems. Requirements for Aviation Maintenance Organizations
I.S. EN 9133:2005	AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - QUALIFICATION PROCEDURE FOR AEROSPACE STANDARD PARTS
BS EN 2882:2006	Aerospace series. Nuts, hexagonal, self-locking, with counterbore and captive washer, in steel, cadmium plated, MoS2 lubricated. Classification: 1100 MPa (at ambient temperature) / 235°C
11/30250206 DC : 0	BS EN 6140 - AEROSPACE SERIES - PLUG, PROTECTIVE, NON METALLIC FOR FITTING ENDS <= 3000 PSI HYDRAULIC SYSTEMS
10/30233643 DC : 0	BS EN 6104 - AEROSPACE SERIES - RIVETS, SOLID, IN ALUMINIUM OR ALUMINIUM ALLOY - INCH SERIES - TECHNICAL SPECIFICATION
BS EN 2337:2006	Aerospace series. Spherical plain bearings. Technical specification
BS EN 2859:2006	Aerospace series. Bolts, normal hexagonal head, close tolerance normal shank, short thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature) / 235°C
BS EN 3626:2006	Aerospace series. Nuts, hexagon, self-locking in steel, cadmium plated, MoS<sub>2</sub> lubricated. Classification: 1100 MPa (at ambient temperature) / 235°C
BS EN 4312:2006	Aerospace series. Studs, coarse tolerance reduced shank, medium length thread, in heat and corrosion resisting steel, with aluminium pigmented coating. Classification: 1100 MPa (at ambient temperature) / 315°C
BS EN 4497:2005	Aerospace series. Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating. Classification: 1 100 MPa (at ambient temperature) / 315 °C
EN 2755:2009	Aerospace series - Bearings, spherical plain in corrosion resisting steel with self-lubricating liner - Elevated load at ambient temperature - Technical specification
CAN/CSA-ISO/IEC TR 29110-5-6-2:18	Systems and software engineering — Lifecycle profiles for Very Small Entities (VSEs) — Part 5-6-2: Systems engineering — Management and engineering guide: Generic profile group: Basic profile (Adopted ISO/IEC TR 29110-5-6-2:2014, first edition, 2014-08-15)
PREN 6098 : DRAFT 2018	AEROSPACE SERIES - ROD-END WITH BEARING PER EN 6097 IN CORROSION RESISTING STEEL, EXTRA WIDE INNER RING, EXTERNAL THREADED SHANK - DIMENSIONS AND LOADS - INCH SERIES
I.S. EN 2882:2006	AEROSPACE SERIES - NUTS, HEXAGONAL, SELF-LOCKING, WITH COUNTERBORE AND CAPTIVE WASHER, IN STEEL, CADMIUM PLATED, MOS[2] LUBRICATED - CLASSIFICATION: 1100 MPA (AT AMBIENT TEMPERATURE)/235 DEGREE C
PREN 4826 : DRAFT 2013	AEROSPACE SERIES - ZINC-NICKEL (12-16% NI) PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER ALLOYS, NICKEL ALLOYS AND ALUMINIUM ALLOYS FOR PARTS AND FASTENERS
PREN 6055 : DRAFT 2018	AEROSPACE SERIES - ROD-END WITH BEARING PER EN 4265 IN CORROSION RESISTING STEEL, EXTERNAL THREADED SHANK - DIMENSIONS AND LOADS - INCH SERIES
PREN 6133 : DRAFT 2018	AEROSPACE SERIES - ROD-END, WITH BEARING PER EN 6096, WITH SELF-LUBRICATING LINER IN CORROSION RESISTING STEEL, EXTRA WIDE INNER RING, EXTERNAL THREADED SHANK - DIMENSIONS AND LOADS - INCH SERIES
PREN 6056 : DRAFT 2018	AEROSPACE SERIES - ROD-END WITH BEARING PER EN 4614 WITH SELF LUBRICATING LINER IN CORROSION RESISTING STEEL WITH EXTERNAL THREADED SHANK - DIMENSIONS AND LOADS - INCH SERIES
PREN 6095 : 200P1	AEROSPACE SERIES - ROTARY FASTENERS - STRUCTURAL AND NON-STRUCTURAL APPLICATIONS - TECHNICAL SPECIFICATION

ISO 19011:2011	Guidelines for auditing management systems
EN 9110:2015	Quality Management Systems - Requirements for Aviation Maintenance Organizations
ISO 9004:2009	Managing for the sustained success of an organization A quality management approach
ISO 9001:2015	Quality management systems — Requirements
ISO 9000:2015	Quality management systems — Fundamentals and vocabulary
ISO 10007:2017	Quality management — Guidelines for configuration management
EN 9120:2010	Quality Management Systems - Requirements for Aviation, Space and Defence Distributors

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Get in touch with us

EN 9100:2009

Quality Management Systems - Requirements for Aviation, Space and Defense Organizations

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory