I.S. EN 528:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RAIL DEPENDENT STORAGE AND RETRIEVAL EQUIPMENT - SAFETY REQUIREMENTS
Hardcopy , PDF
29-03-2021
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant and relevant hazards
5 Safety requirements and/or protective measures for all
types of S/R machines
5.1 Introduction
5.2 Control position
5.3 Control equipment
5.4 Hoist unit
5.5 Travel unit
5.6 Load handling devices
5.7 Electrical equipment
5.8 Transfer device
5.9 Maintenance repair and fault clearance
5.10 Machine environment
6 Additional requirements for manual operated machines
6.1 General
6.2 Onboard control position
6.3 Control equipment
6.4 Hoist unit
6.5 Acceleration and deceleration
6.6 Protection of operators in an aisle containing two
or more manually operated machines
7 Particular requirements for machines without an on-board
operator
7.1 General
7.2 External control position (control desk)
7.3 Control equipment
7.4 Hoist unit
7.5 Load handling devices
7.6 Escape
8 Installation
8.1 Erection and dismantling on site
8.2 Commissioning
9 Verification of safety requirements and/or measures
9.1 Examination
9.2 Written record
9.3 EMC
9.4 Noise
9.5 Load tests
10 Information for use
10.1 General
10.2 Instruction handbook
10.3 Minimum markings
10.4 Conditions for the safe operation of equipment
10.5 Maintenance, inspection and testing
Annex A (informative) Illustration of types of machines and
transfer equipment
Annex B (informative) Means of separation within racking
Annex C (normative) Safety levels according to EN ISO 13849-1
Annex D (informative) Examples for the design of load
entry/exit points to prevent or deter access to
danger areas or protect persons in accordance with 5.10.4
D.1 General
D.2 Measures against access between the conveyor
and fixed guard
D.3 Load entry/exit opening height
D.4 Measures which deter access
D.5 Measures that prevent access
D.6 Protecting devices
Annex E (normative) Verification of safety requirements
and/or measures
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive Machinery 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive Machinery 2006/42/EC
Bibliography
Pertains to all types of S/R machines, restricted to the rails on which they travel within and outside the aisles, which embody lifting means and may embody lateral handling facilities, for the storage and retrieval of unit loads and/or long goods such as bar materials and/or for order picking or similar duties.
| DocumentType |
Standard
|
| Pages |
78
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 528:2008 | Identical |
| SN EN 528 : 2009 | Identical |
| NS EN 528 : 2ED 2008 | Identical |
| NF EN 528 : 2008 | Identical |
| UNI EN 528 : 2009 | Identical |
| UNE-EN 528:2009 | Identical |
| NBN EN 528 : 2009 | Identical |
| NEN EN 528 : 2008 | Identical |
| ONORM EN 528 : 2009 | Identical |
| DIN EN 528:2009-02 | Identical |
| EN 528:2008 | Identical |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| ISO 4308-1:2003 | Cranes and lifting appliances Selection of wire ropes Part 1: General |
| EN 12385-4:2002+A1:2008 | Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN 61000-6-3:2007/A1:2011/AC:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN 61310-3:2008 | Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| IEC 61310-3:2007 | Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators |
| EN 1760-1:1997+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors |
| IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN 81-1:1998+A3:2009 | Safety rules for the construction and installation of lifts - Part 1: Electric lifts |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN 13411-3:2004+A1:2008 | Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| DIN 15350:1992-04 | STORAGE AND RETRIEVAL MACHINES - RULES FOR CALCULATIONS OF STEEL STRUCTURES |
| EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| IEC 61000-6-3:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments |
| EN 1263-1:2014 | Temporary works equipment - Safety nets - Part 1: Safety requirements, test methods |
| EN 1263-2:2014 | Temporary works equipment - Safety nets - Part 2: Safety requirements for the positioning limits |
| CLC/TS 61496-3:2008 | Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR) |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN 61496-1:2013/AC:2015 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012) |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| IEC 61496-3:2008 | Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR) |
| ZH 1/361 : 1978 | GUIDELINES FOR APPLIANCES AND SYSTEMS FOR SHELF OPERATION |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN 81-2 : 1998 + A3 2009 | SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 2: HYDRAULIC LIFTS |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| EN 13411-6:2004+A1:2008 | Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| EN 363:2008 | Personal fall protection equipment - Personal fall protection systems |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 1760-3:2004+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN 795:2012 | Personal fall protection equipment - Anchor devices |
| ISO 13050:2014 | Synchronous belt drives Metric pitch, curvilinear profile systems G, H, R and S, belts and pulleys |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.