I.S. EN 61019-1:2005
Current
The latest, up-to-date edition.
SURFACE ACOUSTIC WAVE (SAW) RESONATORS - PART 1: GENERIC SPECIFICATION
Hardcopy , PDF
English
01-01-2005
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
1 Scope
2 Normative references
3 Order of precedence
4 Terms and definitions
4.1 General terms
4.2 Operational properties
5 Preferred values for ratings and characteristics
5.1 Standard nominal frequency values in megahertz (MHz)
5.2 Standard operating temperature ranges in degrees
Celsius (degrees C)
5.3 Standard values of load capacitance in picofarads (pF)
5.4 Standard levels of drive in milliwatts (mW)
5.5 Standard values of minimum insertion attenuation in
decibels (dB)
5.6 Standard climatic category
5.7 Bump severity
5.8 Vibration severity
5.9 Shock severity
5.10 Fine leak rate
6 Marking
6.1 Resonator marking
6.2 Package marking
7 Quality assessment procedures
7.1 Primary stage of manufacture
7.2 Structurally similar components
7.3 Subcontracting
7.4 Incorporated components
7.5 Manufacturer's approval
7.6 Approval procedures
7.7 Procedures for capability approval
7.8 Procedures for qualification approval
7.9 Test procedures
7.10 Screening requirements
7.11 Rework and repair work
7.12 Certified records of released lots
7.13 Validity of release
7.14 Release for delivery
7.15 Unchecked parameters
8 Test and measurement procedures
8.1 General
8.2 Test and measurement conditions
8.3 Visual inspection
8.4 Dimensions and gauging procedures
8.5 Measurement method of one-port resonator
8.6 Measurement method of two-port resonator
8.7 Mechanical and environmental test procedures
8.8 Endurance test procedure
Figures
Defines the methods of test and general requirements for SAW resonators using either capability approval or qualification approval procedures of the IECQ system.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
52
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 61019-1:2005 | Identical |
| IEC 61019-1:2004 | Identical |
| DIN EN 61019-1:2005-06 | Identical |
| NBN EN 61019-1 : 2005 | Identical |
| NF EN 61019-1 : 2005 | Identical |
| BS EN 61019-1:2005 | Identical |
| HD 323.2.20 : 200S3 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST T - SOLDERING |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60068-2-58:2015+AMD1:2017 CSV | Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IECQ 001002-3:2005 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 3: APPROVAL PROCEDURES |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| EN 60068-2-64:2008 | ENVIRONMENTAL TESTING - PART 2-64: TESTS - TEST FH: VIBRATION, BROADBAND RANDOM AND GUIDANCE |
| IECQ 001002-2:1998 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 2: DOCUMENTATION |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| EN 60068-2-7:1993 | Environmental testing - Part 2: Tests - Test Ga: Acceleration, steady state |
| IEC 60068-2-64:2008 | Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance |
| EN 61019-2:2005 | Surface acoustic wave (SAW) resonators - Part 2: Guide to the use |
| EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 61019-2:2005 | Surface acoustic wave (SAW) resonators - Part 2: Guide to the use |
| EN 60068-2-17:1994 | Environmental testing - Part 2: Tests - Test Q: Sealing |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| EN 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| EN 60068-2-29:1993 | Environmental testing - Part 2: Tests - Test Eb and guidance: Bump |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| EN 60068-2-13:1999 | Environmental testing - Part 2: Tests - Test M: Low air pressure |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| IEC 60050-561:2014 | International Electrotechnical Vocabulary (IEV) - Part 561: Piezoelectric, dielectric and electrostatic devices and associated materials for frequency control, selection and detection |
| IEC 60122-1:2002 | Quartz crystal units of assessed quality - Part 1: Generic specification |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| IEC 61019-3:1991 | Surface acoustic wave (SAW) resonators - Part 3: Standard outlines and lead connections |
| EN 60068-2-32:1993 | Basic environmental testing procedures - Part 2: Tests - Test Ed: Free fall |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| EN 60068-2-45:1992/A1:1993 | Environmental testing - Part 2: Tests - Test Xa and guidance: Immersion in cleaning solvents |
| EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60068-2-52:2017 | Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.