IEC 61083-1:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Instruments and software used for measurement in high-voltage impulse tests - Part 1: Requirements for instruments
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
31-12-2021
English - French, Spanish, Castilian
11-06-2001
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
1 General
1.1 Scope
1.2 Normative references
1.3 Terms and definitions
1.3.1 General definitions
1.3.2 Definitions specific for digital
recorders and analogue oscilloscopes
1.3.3 Definitions specific for digital recorders
1.4 Operating conditions
1.5 Calibration and test methods
1.5.1 Impulse calibration
1.5.2 Step calibration
1.5.3 Constancy of scale factor within time interval
1.5.4 Time base
1.5.5 Rise time
1.5.6 Voltage deflection characteristic of
analogue oscilloscopes
1.5.7 Determination of static differential and
integral non-linearities
1.5.8 Differential non-linearity under dynamic
conditions
1.5.9 Internal noise level
1.5.10 Interference
1.6 Input impedance
2 Digital recorders for impulse tests
2.1 Requirements for impulse measurements
2.1.1 Requirements for digital recorders used
in approved measuring systems
2.1.2 Individual requirements
2.1.3 Requirements for digital recorders used
in reference measuring systems
2.1.4 Tests
2.1.5 Record of performance
3 Analogue oscilloscopes for impulse tests
3.1 Requirements for impulse measurements
3.1.1 Requirements for analogue oscilloscopes
used in approved measuring systems
3.1.2 Individual requirements
3.1.3 Tests
3.1.4 Record of performance
4 Peak voltmeters for impulse tests
4.1 Requirements for impulse measurements
4.1.1 General requirements for peak voltmeters
4.1.2 Individual requirements
4.1.3 Tests
4.1.4 Record of performance
Annex A (normative) Procedure for determination of
non-linearities of a digital recorder
Annex B (normative) Electromagnetic interference
in high-voltage laboratories
Annex C (normative) Calibration method for analogue
oscilloscopes - Separate calibration of
voltage and time
Annex D (informative) Analysis of impulse waveform
Applies to digital recorders and digital oscilloscopes used for measurements during tests with high impulse voltages and high impulse currents. Specifies the measuring characteristics and calibrations required to meet the measuring accuracies and procedures given in IEC 60-1.
| Committee |
TC 42
|
| DevelopmentNote |
Supersedes IEC 60790 (06/2001) Also numbered as BS EN 61083-1. (10/2001) Stability Date: 2017. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
69
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 61083-1 : 2001 | Identical |
| NEN 11083-1 : 1993 | Identical |
| NEN EN IEC 61083-1 : 2001 | Identical |
| I.S. EN 61083-1:1993 | Identical |
| PN EN 61083-1 : DEC 2002 | Identical |
| SN EN 61083-1 : 2001 | Identical |
| AS 61083.1-2006 | Identical |
| DIN EN 61083-1 : 2002 | Identical |
| VDE 0432-7 : 2002 | Identical |
| UNE-EN 61083-1:2002 | Identical |
| CEI EN 61083-1 : 2002 | Identical |
| EN 61083-1:2001 | Corresponds |
| BS EN 62475:2010 | High-current test techniques. Definitions and requirements for test currents and measuring systems |
| CEI EN 62008 : 2006 | PERFORMANCE CHARACTERISTICS AND CALIBRATION METHODS FOR DIGITAL DATA ACQUISITION SYSTEMS AND RELEVANT SOFTWARE |
| 06/30149562 DC : DRAFT APR 2006 | IEC 61083-2 - INSTRUMENTS AND SOFTWARE USED FOR MEASUREMENTS IN HIGH-VOLTAGE IMPULSE TEST - PART 2: REQUIREMENTS FOR SOFTWARE |
| NF EN 60060-2 : 2011 | HIGH-VOLTAGE TEST TECHNIQUES - PART 2: MEASURING SYSTEMS |
| CEI EN 62475 : 2011 | HIGH-CURRENT TEST TECHNIQUES - DEFINITIONS AND REQUIREMENTS FOR TEST CURRENTS AND MEASURING SYSTEMS |
| 07/30161538 DC : 0 | BS EN 60060-2 - HIGH-VOLTAGE TEST TECHNIQUES - PART 2: MEASURING SYSTEMS |
| CEI EN 61083-2 : 2014 | INSTRUMENTS AND SOFTWARE USED FOR MEASUREMENT IN HIGH-VOLTAGE AND HIGH-CURRENT TESTS - PART 2: REQUIREMENTS FOR SOFTWARE FOR TESTS WITH IMPULSE VOLTAGES AND CURRENTS |
| BS EN 61643-21 : 2001 | LOW VOLTAGE SURGE PROTECTIVE DEVICES - PART 21: SURGE PROTECTIVE DEVICES CONNECTED TO TELECOMMUNICATIONS AND SIGNALLING NETWORKS - PERFORMANCE REQUIREMENTS AND TESTING METHODS |
| IEEE C62.50-2012 | IEEE Standard for Performance Criteria and Test Methods for Plug-in (Portable) Multiservice (Multiport) Surge-Protective Devices for Equipment Connected to a 120 V/240 V Single Phase Power Service and Metallic Conductive Communication Line(s) |
| IEC 61180-2:1994 | High-voltage test techniques for low-voltage equipment - Part 2: Test equipment |
| EN 61083-2:2013 | Instruments and software used for measurement in high-voltage and high-current tests - Part 2: Requirements for software for tests with impulse voltages and currents |
| EN 62008:2005 | Performance characteristics and calibration methods for digital data acquisition systems and relevant software |
| EN 61180:2016 | High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment |
| EN 61180-2:1994 | High-voltage test techniques for low-voltage equipment - Part 2: Test equipment |
| EN 60060-2:2011 | High-voltage test techniques - Part 2: Measuring systems |
| EN 62475 : 2010 | HIGH-CURRENT TEST TECHNIQUES - DEFINITIONS AND REQUIREMENTS FOR TEST CURRENTS AND MEASURING SYSTEMS |
| CEI EN 61643-341 : 2002 | COMPONENTS FOR LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 341: SPECIFICATION FOR THYRISTOR SURGE SUPPRESSOR (TSS) |
| CEI EN 60076-3 : 2015 | POWER TRANSFORMERS - PART 3: INSULATION LEVELS, DIELECTRIC TESTS AND EXTERNAL CLEARANCES IN AIR |
| 03/100554 DC : DRAFT APR 2003 | IEC 60060-3 ED.1 - HIGH VOLTAGE TEST TECHNIQUES - PART 3: DEFINITIONS AND REQUIREMENTS FOR ON-SITE TESTS |
| BS EN 60060-2:1995 | High-voltage test techniques Measuring systems |
| BS EN 62008:2005 | Performance characteristics and caliberation for digital data acquisition systems and relevant software |
| BS EN 61083-2:2013 | Instruments and software used for measurement in high-voltage and high-current tests Requirements for software for tests with impulse voltages and currents |
| CEI EN 60076-4 : 2003 | POWER TRANSFORMERS - PART 4: GUIDE TO LIGHTNING IMPULSE AND SWITCHING IMPULSE TESTING - POWER TRANSFORMERS AND REACTORS |
| DIN EN 61180-2 : 1995 | HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - PART 2: TEST EQUIPMENT |
| VDE 0432-11 : 1995 | HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - PART 2: TEST EQUIPMENT |
| IEC TS 62561-8:2018 | Lightning protection system components (LPSC) - Part 8: Requirements for components for isolated LPS |
| IEC 61643-21:2000+AMD1:2008+AMD2:2012 CSV | Low voltage surge protective devices - Part 21: Surge protective devices connected to telecommunications and signalling networks - Performance requirements and testing methods |
| I.S. EN 62008:2005 | PERFORMANCE CHARACTERISTICS AND CALIBRATION METHODS FOR DIGITAL DATA ACQUISITION SYSTEMS AND RELEVANT SOFTWARE |
| I.S. EN 60076-4:2002 | POWER TRANSFORMERS - PART 4: GUIDE TO THE LIGHTNING IMPULSE AND SWITCHING IMPULSE TESTING - POWER TRANSFORMERS AND REACTORS |
| IEC 60060-2:2010 | High-voltage test techniques - Part 2: Measuring systems |
| IEEE 4-2013 | IEEE Standard for High-Voltage Testing Techniques |
| 10/30232718 DC : 0 | BS EN 60076-3 - POWER TRANSFORMERS - PART 3: INSULATION LEVELS, DIELECTRIC TESTS AND EXTERNAL CLEARANCES IN AIR |
| NF EN 61211 : 2005 | INSULATORS OF CERAMIC MATERIAL OR GLASS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE GREATER THAN 1 000 V - IMPULSE PUNCTURE TESTING IN AIR |
| CEI EN 61180 : 1ED 2017 | HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - DEFINITIONS, TEST AND PROCEDURE REQUIREMENTS, TEST EQUIPMENT |
| I.S. EN 60060-2:2011 | HIGH-VOLTAGE TEST TECHNIQUES - PART 2: MEASURING SYSTEMS |
| I.S. EN 61211:2005 | INSULATORS OF CERAMIC MATERIAL OR GLASS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE GREATER THAN 1000 V - IMPULSE PUNCTURE TESTING IN AIR |
| ISO 23552-1:2007 | Safety and control devices for gas and/or oil burners and gas and/or oil appliances — Particular requirements — Part 1: Fuel/air ratio controls, electronic type |
| IEC 60076-3:2013+AMD1:2018 CSV | POWER TRANSFORMERS - PART 3: INSULATION LEVELS, DIELECTRIC TESTS AND EXTERNAL CLEARANCES IN AIR |
| IEC 61180:2016 | High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment |
| EN 61643-341:2001 | Components for low-voltage surge protective devices - Part 341: Specification for thyristor surge suppressors (TSS) |
| BS EN 60060-1:2010 | High-voltage test techniques General definitions and test requirements |
| I.S. EN 60076-3:2013 | POWER TRANSFORMERS - PART 3: INSULATION LEVELS, DIELECTRIC TESTS AND EXTERNAL CLEARANCES IN AIR |
| BIS IS/IEC 60060-2 : 2010 | HIGH-VOLTAGE TEST TECHNIQUES - PART 2: MEASURING SYSTEMS |
| DIN IEC 60060-1 : 1994 | HIGH VOLTAGE TEST TECHNIQUES - GENERAL SPECIFICATIONS AND TEST REQUIREMENTS |
| 13/30294291 DC : 0 | BS EN 62561-8 - LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 8: REQUIREMENTS FOR COMPONENTS FOR ISOLATED LPS |
| BS EN 60076-4:2002 | Power transformers Guide to the lightning impulse and switching impulse testing. Power transformers and reactors |
| BS EN 61643-341:2001 | Low voltage surge protective devices Specification for thyristor surge suppressors (TSS) |
| BS EN 61211:2005 | Insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1000 V. Impulse puncture testing in air |
| BS EN 61180-2:1995 | High-voltage test techniques for low-voltage equipment Test equipment |
| DIN EN 61180-1 : 1995 | HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - PART 1: DEFINITIONS, TEST AND PROCEDURE REQUIREMENTS |
| UNE-EN 60060-2:2012 | High-voltage test techniques -- Part 2: Measuring systems. |
| CEI EN 60060-1 : 2015 | HIGH-VOLTAGE TEST TECHNIQUES - PART 1: GENERAL DEFINITIONS AND TEST REQUIREMENTS |
| I.S. EN 61180-2:1995 | HIGH VOLTAGE TEST TECHNIQUE FOR LOW-VOLTAGE EQUIPMENT - PART 2: TEST EQUIPMENT |
| I.S. EN 61180:2016 | HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - DEFINITIONS, TEST AND PROCEDURE REQUIREMENTS, TEST EQUIPMENT |
| I.S. EN 61643-21:2001 | LOW VOLTAGE SURGE PROTECTIVE DEVICES - PART 21: SURGE PROTECTIVE DEVICES CONNECTED TO TELECOMMUNICATIONS AND SIGNALLING NETWORKS - PERFORMANCE REQUIREMENTS AND TESTING METHODS (IEC 61643-21:2000 (EQV) + CORRIGENDUM MAR. 2001 (EQV)) |
| I.S. EN 60060-1:2010 | HIGH-VOLTAGE TEST TECHNIQUES - PART 1: GENERAL DEFINITIONS AND TEST REQUIREMENTS |
| IEC 60076-4:1976 | Power transformers - Part 4: Tappings and connections |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 62008:2005 | Performance characteristics and calibration methods for digital data acquisition systems and relevant software |
| IEC 61211:2004 | Insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1 000 V - Impulse puncture testing in air |
| IEC 61083-2:2013 | Instruments and software used for measurement in high-voltage and high-current tests - Part 2: Requirements for software for tests with impulse voltages and currents |
| IEC 62475:2010 | High-current test techniques - Definitions and requirements for test currents and measuring systems |
| UNE-EN 60060-1:2012 | High-voltage test techniques - Part 1: General definitions and test requirements |
| UNE-EN 61180:2017 | High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment |
| 12/30265513 DC : DRAFT MAY 2012 | BS EN 61180 - HIGH-VOLTAGE TEST TECHNIQUES FOR LOW VOLTAGE EQUIPMENT - DEFINITIONS, TEST AND PROCEDURE REQUIREMENTS, TEST EQUIPMENT |
| UNE-EN 62475:2012 | High-current test techniques - Definitions and requirements for test currents and measuring systems |
| I.S. EN 62475:2010 | HIGH-CURRENT TEST TECHNIQUES - DEFINITIONS AND REQUIREMENTS FOR TEST CURRENTS AND MEASURING SYSTEMS |
| BS EN 60076-3 : 2013 | POWER TRANSFORMERS - PART 3: INSULATION LEVELS, DIELECTRIC TESTS AND EXTERNAL CLEARANCES IN AIR |
| I.S. EN 61083-2:2013 | INSTRUMENTS AND SOFTWARE USED FOR MEASUREMENT IN HIGH-VOLTAGE AND HIGH-CURRENT TESTS - PART 2: REQUIREMENTS FOR SOFTWARE FOR TESTS WITH IMPULSE VOLTAGES AND CURRENTS (IEC 61083-2:2013 (EQV)) |
| CEI EN 60060-2 : 2015 | HIGH-VOLTAGE TEST TECHNIQUES - PART 2: MEASURING SYSTEMS |
| IEC 61643-341:2001 | Components for low-voltage surge protective devices - Part 341: Specification for thyristor surge suppressors (TSS) |
| EN 61643-21:2001/A2:2013 | LOW VOLTAGE SURGE PROTECTIVE DEVICES - PART 21: SURGE PROTECTIVE DEVICES CONNECTED TO TELECOMMUNICATIONS AND SIGNALLING NETWORKS - PERFORMANCE REQUIREMENTS AND TESTING METHODS (IEC 61643-21:2000/A2:2012) |
| EN 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| EN 60076-4:2002 | Power transformers - Part 4: Guide to the lightning impulse and switching impulse testing - Power transformers and reactors |
| EN 61211:2005 | Insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1 000 V - Impulse puncture testing in air |
| EN 60076-3:2013/A1:2018 | POWER TRANSFORMERS - PART 3: INSULATION LEVELS, DIELECTRIC TESTS AND EXTERNAL CLEARANCES IN AIR (IEC 60076-3:2013/A1:2018) |
| IEC 60060-2:2010 | High-voltage test techniques - Part 2: Measuring systems |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.