IEC 62282-2:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Fuel cell technologies - Part 2: Fuel cell modules
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
31-12-2021
English - French, Spanish, Castilian
26-03-2012
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Type tests
6 Routine tests
7 Markings and instructions
Annex A (informative) - Additional information for the
performance and evaluation of the tests
Annex B (informative) - List of notes concerning
particular conditions in certain countries
Bibliography
IEC 62282-2:2012 provides the minimum requirements for safety and performance of fuel cell modules; it applies to fuel cell modules with or without an enclosure which can be operated at significant pressurization levels or close to ambient pressure. Deals with conditions that can yield hazards to persons and cause damage outside the fuel cell modules. This edition includes the following significant technical changes with respect to the previous edition:
- inclusion of definitions for hazards and hazardous locations based on the IEC 60079 series;
- modification of the general safety strategy and of the electrical components clause to reflect the needs for different application standards. Key word: fuel cell
| Committee |
TC 105
|
| DevelopmentNote |
Stability Date: 2015. (10/2012)
|
| DocumentType |
Standard
|
| Pages |
82
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| GOST R IEC 62282-2 : 2014 | Identical |
| NF EN 62282-2 : 2012 | Identical |
| NBN EN 62282-2 : 2012 | Identical |
| NEN EN IEC 62282-2 : 2012 | Identical |
| PN EN 62282-2 : 2012 | Identical |
| DIN EN 62282-2 : 2013 | Identical |
| VDE 0130-2 : 2013 | Identical |
| UNE-EN 62282-2:2012 | Identical |
| CEI EN 62282-2 : 2013 | Identical |
| EN 62282-2:2012 | Identical |
| OVE/ONORM EN 62282-2 : 2013 | Identical |
| VDE 0130-201 : 2008 | Identical |
| BS EN 62282-2:2012 | Identical |
| PD IEC/TS 62282-7-2:2014 | Fuel cell technologies Test methods. Single cell and stack performance tests for solid oxide fuel cells (SOFC) |
| BS EN 62282-3-1:2007 | Fuel cell technologies Stationary fuel cell power systems. Safety |
| 05/30060689 DC : DRAFT JUN 2005 | IEC 62282-3-1 - FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER PLANTS - SAFETY |
| EN 62282-3-1 : 2007 | FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| BS EN 62282-5-1:2012 | Fuel cell technologies Portable fuel cell power systems. Safety |
| PREN 50465 : DRAFT 2011 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| I.S. EN 62282-3-1:2007 | FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| IEC 62282-5-1:2012 | Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety |
| UNE-EN 62282-3-1:2011 | Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety |
| SAE AIR 6464 : 2013 | EUROCAE/SAE WG80/AE-7AFC HYDROGEN FUEL CELLS AIRCRAFT FUEL CELL SAFETY GUIDELINES |
| 13/30276640 DC : 0 | BS EN 62282-4-101 ED 1.0 - FUEL CELL TECHNOLOGIES - PART 4-101: FUEL CELL POWER SYSTEMS FOR PROPULSION FOR OTHER THAN ROAD VEHICLES AND AUXILIARY POWER UNITS - FUEL CELL POWER SYSTEMS FOR ELECTRICALLY POWERED INDUSTRIAL TRUCKS - SAFETY |
| BS EN 62282-4-101:2014 | Fuel cell technologies Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU). Safety of electrically powered industrial trucks |
| IEC 62282-4-101:2014 | Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks |
| UNE-EN 62282-5-1:2013 | Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety |
| 10/30173705 DC : DRAFT SEP 2010 | BS EN 62282-5-1 - FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY |
| 11/30249911 DC : 0 | BS EN 50465 - GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| 07/30091745 DC : 0 | BS IEC 62368 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - SAFETY - REQUIREMENTS |
| 16/30354067 DC : 0 | BS EN 62282-5-100 - FUEL CELL TECHNOLOGIES - PART 5-100: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY |
| IEC 62282-3-1:2007 | Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety |
| EN 62282-5-1:2012 | FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012) |
| EN 62282-4-101:2014 | Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| CSA B51 : 2014 | BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC TS 62282-1:2013 | Fuel cell technologies - Part 1: Terminology |
| ISO 4672:1997 | Rubber and plastics hoses Sub-ambient temperature flexibility tests |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| IEC 60079-20-1:2010 | Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data |
| IEC 62040-1:2017 EXV | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS |
| CGA 12.6 : M94(R1999) | VEHICLE REFUELLING APPLIANCES |
| EN 50178:1997 | Electronic equipment for use in power installations |
| CSA C22.2 No. 60529 : 2016 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) |
| SAE J1739_200901 | Potential Failure Mode and Effects Analysis in Design (Design FMEA), Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 62282-3-100:2012 | Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 1402:2009 | Rubber and plastics hoses and hose assemblies Hydrostatic testing |
| ISO 1307:2006 | Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| ISO 1436:2017 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 23550:2011 | Safety and control devices for gas burners and gas-burning appliances General requirements |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.