KTA 3201.2 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS - PART 2: DESIGN AND ANALYSIS
24-10-2024
12-01-2013
Fundamentals
1 Scope
2 General requirements and definitions
3 Load case classes as well as design, service
and test loadings and limits of components
4 Effects on the components due to mechanical
and thermal loadings, fluid effects and irradiation
5 Design
6 Dimensioning
7 General analysis of the mechanical behaviour
8 Component-specific analysis of the mechanical behaviour
9 Type and extent of verification of strength and pertinent
documents to be submitted
Annex A: Dimensioning
Annex B: Requirements as to the primary stress analysis in
case of numerical reassessments
Annex C: Calculation methods
Annex D: Brittle fracture analysis procedures
Annex E: Regulations referred to in this Safety Standard
Annex F: Changes with respect to the edition 1996-06 and
explanations (informative)
Pertains to the design and analysis of the components of the reactor coolant pressure boundary of light water reactors made of metallic materials, which are operated up to design temperatures of 673 K (400 degrees C).
| DevelopmentNote |
DRAFT 2017 issued in November 2017. (02/2018)
|
| DocumentType |
Standard
|
| PublisherName |
Kerntechnischer Ausschuss
|
| Status |
Superseded
|
| SupersededBy |
| VDI 3842:2004-06 | Vibrations in piping systems |
| KTA 3407 : 2014 | PIPE PENETRATIONS THROUGH THE REACTOR CONTAINMENT VESSEL |
| KTA 3101.3 : 2015(R2017) | DESIGN OF REACTOR CORES OF PRESSURIZED WATER AND BOILING WATER REACTORS - PART 3: MECHANICAL AND THERMAL DESIGN |
| VDI 2200:2007-06 | Tight flange connections - Selection, calculation, design and assembly of bolted flange connections |
| DIN 2413:2011-06 | SEAMLESS STEEL TUBES FOR OIL- AND WATER-HYDRAULIC SYSTEMS - CALCULATION RULES FOR PIPES AND ELBOWS FOR DYNAMIC LOADS |
| KTA 3103 : 2015(R2017) | SHUTDOWN SYSTEMS FOR LIGHT WATER REACTORS |
| KTA 3205.2 : 2015 COR 2016 | COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT |
| KTA 3206 : 2014(R2017)Berichtigung:2019 | BREAK PRECLUSION VERIFICATIONS FOR PRESSURE-RETAINING COMPONENTS IN NUCLEAR POWER PLANTS |
| KTA 3201.3 : 2007(R2012) | COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS - PART 3: MANUFACTURE |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| DIN EN ISO 898-1:2013-05 | MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 1: BOLTS, SCREWS AND STUDS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD (ISO 898-1:2013) |
| DIN EN ISO 3506-1:2010-04 | MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 1: BOLTS, SCREWS AND STUDS |
| DIN 2510-4:1971-08 | BOLTED CONNECTIONS WITH REDUCED SHANK; STUDS |
| DIN 28013:2012-06 | ELLIPSOIDAL HEADS |
| KTA 3203 : 2001(R2011) | SURVEILLANCE OF THE IRRADIATION BEHAVIOUR OF REACTOR PRESSURE VESSEL MATERIALS OF LWR FACILITIES |
| ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress |
| DIN EN 10253-2:2008-09 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
| DIN EN ISO 3506-2:2010-04 | MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS |
| DIN EN 13555:2014-07 | Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections |
| DIN 267-13:2007-05 | FASTENERS - TECHNICAL SPECIFICATIONS - PART 13: PARTS FOR BOLTED CONNECTIONS WITH SPECIFIC MECHANICAL PROPERTIES FOR USE AT TEMPERATURES RANGING FROM -200 DEGREE C TO +700 DEGREE C |
| KTA 3205.1 : 2002(R2007) | COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 1: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS |
| DIN EN 10253-4:2008-06 | Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements |
| PD 5500:2000 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| KTA 3201.3 : 2007(R2012) | COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS - PART 3: MANUFACTURE |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| DIN 28011:2012-06 | TOROSPHERICAL HEADS |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.