CSA C22.2 No. 60065 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
Available format(s)
Hardcopy , PDF
Superseded date
19-10-2020
Superseded by
Language(s)
English
Published date
01-01-2016
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 General
2 Terms and definitions
3 General requirements
4 General test conditions
5 Marking and instructions
6 Hazardous radiations
7 Heating under normal operating conditions
8 Constructional requirements with regard to the protection
against electric shock
9 Electric shock hazard under normal operating conditions
10 Insulation requirements
11 Fault conditions
12 Mechanical strength
13 CLEARANCES and CREEPAGE DISTANCES
14 Components
15 TERMINALS
16 External flexible cords
17 Electrical connections and mechanical fixings
18 Mechanical strength of picture tubes and protection
against the effects of implosion
19 Stability and mechanical hazards
20 Resistance to fire
Annex A (normative) - Additional requirements for apparatus
with protection against splashing water
Annex B (normative) - Apparatus to be connected to the
TELECOMMUNICATION NETWORKS
Annex C (normative) - Band-pass filter for wide-band noise
measurement
Annex D (normative) - Measuring network for TOUCH CURRENTS
Annex E (normative) - Measurement of CLEARANCES and
CREEPAGE DISTANCES
Annex F (normative) - Table of electrochemical potentials
Annex G (normative) - Flammability test methods
Annex H (normative) - Insulated winding wires for use
without interleaved insulation
Annex I (Void)
Annex J (normative) - Alternative method for determining
minimum CLEARANCES
Annex K (normative) - Impulse test generators
Annex L (normative) - Additional requirements for electronic
flash apparatus for photographic purposes
Annex M (informative) - Examples of requirements for quality
control programmes for allowing reduced clearances
Annex N (informative) - Routine tests
Annex NA (normative) - Additional requirements for apparatus
for use in health care facilities
Annex NB (normative) - Additional requirements for apparatus
for kitchen under-cabinet Equipment
Annex NC (normative) - Additional requirements for
power-operated radio transmitters and similar
apparatus
Bibliography
This Standard applies to power-operated radio transmitting equipment designed to be used on standard supply circuits in accordance with CSA C22.1, Canadian Electrical Code, Part I, including all types of radio transmitting equipment, irrespective of the type of modulation employed.
| DevelopmentNote |
Supersedes CSA E60065 (05/2003)
|
| DocumentType |
Standard
|
| ISBN |
978-1-4883-0213-8
|
| Pages |
420
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| CSA C22.2 No. 308 : 2014 | CORD REELS AND MULTI-OUTLET ASSEMBLIES |
| CSA E60691:2008 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE |
| CSA B354.5 : 2007 : R2016 | MAST-CLIMBING WORK PLATFORMS |
| CSA E60691 : 2008 : R2012 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE |
| CSA C22.2 No. 21 : 2014 | CORD SETS AND POWER-SUPPLY CORDS |
| CSA C22.2 No. 60691 : 2015 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE |
| CSA C22.2 No. 1 : 2004 | AUDIO, VIDEO AND SIMILAR ELECTRONIC EQUIPMENT |
| CSA C22.2 No. 107.3 : 2014 | UNINTERRUPTIBLE POWER SYSTEMS |
| B354.12-17 | Design, calculations, safety requirements, and test methods for mast climbing transport platforms (MCTPs) |
| CSA C22.2 No. 62368-1 : 2014 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| CSA C22.2 No. 287 : 2016 | PLUMBING FITTINGS INCORPORATING ELECTRICAL AND/OR ELECTRONIC FEATURES |
| CSA C22.2 No. 207 : 2015 | PORTABLE AND STATIONARY ELECTRIC SIGNS AND DISPLAYS |
| B354.9-17 | Design, calculations, safety requirements, and test methods for mast climbing work platforms (MCWPs) |
| CSA C22.2 No. 199 : 2007 : INC : ADD A : 2010 : R2012 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR AUTOMATIC BURNER IGNITION SYSTEMS AND COMPONENTS |
| UL 1993:5ED 2017-01-27 | Self-Ballasted Lamps and Lamp Adapters |
| CSA C22.2 No. 144.1 : 2016 | GROUND-FAULT CIRCUIT-INTERRUPTERS |
| CSA C22.2 No. 66.1 : 2006 : INC : UPD 2 : 2013 : R201100 | LOW VOLTAGE TRANSFORMERS - PART 1: GENERAL REQUIREMENTS |
| CSA C22.2 No. 112 : 2015 | ELECTRIC CLOTHES DRYERS |
| UL 1786:4ED 2014-12-17 | Direct Plug-In Nightlights |
| C22.2 NO. 1993-17 | Self-ballasted lamps and lamp adapters (Trinational standard with NMX-J-578/1-ANCE and UL 1993) |
| CSA C22.2 No. 66.1 : 2006 : INC : UPD 1 : 2012 : R201100 | LOW VOLTAGE TRANSFORMERS - PART 1: GENERAL REQUIREMENTS |
| CSA C22.2 No. 61347-2-13 : 2015(R2020) | LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES |
| UL 943:5ED 2016-05-17 | Ground-Fault Circuit-Interrupters |
| UL 1778:5ED 2014-06-13 | Uninterruptible Power Systems |
| CSA C22.2 No. 66.1 : 2006 : R2011 | LOW VOLTAGE TRANSFORMERS - PART 1: GENERAL REQUIREMENTS |
| CSA C22.2 No. 66.1 : 2006 | LOW VOLTAGE TRANSFORMERS - PART 1: GENERAL REQUIREMENTS |
| CSA C22.2 No. 66.1 : 2006 : R2015 | LOW VOLTAGE TRANSFORMERS - PART 1: GENERAL REQUIREMENTS |
| CSA E60335.2.82 : 2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-82: PARTICULAR REQUIREMENTS FOR AMUSEMENT MACHINES AND PERSONAL SERVICE MACHINES |
| CSA SPE 3000 : 2015 | MODEL CODE FOR THE FIELD EVALUATION OF MEDICAL ELECTRICAL EQUIPMENT AND SYSTEMS |
| CSA C22.2 No. 255 : 2004 | NEON TRANSFORMERS AND POWER SUPPLIES |
| CSA B354.5 : 2007 : INC : UPD 1 : 2008 : R2011 | MAST-CLIMBING WORK PLATFORMS |
| CSA B354.5:2007 | MAST-CLIMBING WORK PLATFORMS |
| CSA C22.2 No. 256 : 2014 | DIRECT PLUG-IN NIGHTLIGHTS |
| CSA C22.2 No. 199 : 2007 : INC : ADD A : 2010 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR AUTOMATIC BURNER IGNITION SYSTEMS AND COMPONENTS |
| CSA C22.2 No. 199 : 2007 : R2011 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR AUTOMATIC BURNER IGNITION SYSTEMS AND COMPONENTS |
| CSA C22.2 No. 250.13 : 2017 | LIGHT EMITTING DIODE (LED) EQUIPMENT FOR LIGHTING APPLICATIONS |
| CSA C22.2 No. 223 : 2015 | POWER SUPPLIES WITH EXTRA-LOW-VOLTAGE CLASS 2 OUTPUTS |
| CSA C22.2 No. 255 : 2004 : R2014 | NEON TRANSFORMERS AND POWER SUPPLIES |
| CSA C22.2 No. 199 :2007 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR AUTOMATIC BURNER IGNITION SYSTEMS AND COMPONENTS |
| CSA C22.2 No. 61347-2-13 : 2015 | LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES |
| CSA E60335.2.79 : 2009 : R2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-79: PARTICULAR REQUIREMENTS FOR HIGH PRESSURE CLEANERS |
| CSA E60335.2.79 : 2009 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-79: PARTICULAR REQUIREMENTS FOR HIGH PRESSURE CLEANERS |
| CSA SPE.1000 : 2013 | MODEL CODE FOR THE FIELD EVALUATION OF ELECTRICAL EQUIPMENT |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 60320-1:2015 | Appliance couplers for household and similar general purposes - Part 1: General requirements |
| IEC 60335-2-82:2017 | Household and similar electrical appliances - Safety - Part 2-82: Particular requirements for amusement machines and personal service machines |
| IEC 60728-11:2016 | Cable networks for television signals, sound signals and interactive services - Part 11: Safety |
| IEC 60038:2009 | IEC standard voltages |
| IEC 61558-2-1:2007 | Safety of power transformers, power supplies, reactors and similar products - Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications |
| IEC 60107-1:1997 | Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequencies |
| IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
| CSA C22.2 No. 223 : 2015 | POWER SUPPLIES WITH EXTRA-LOW-VOLTAGE CLASS 2 OUTPUTS |
| IEC 60384-14:2013+AMD1:2016 CSV | Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
| IEC 60127-6:2014 | Miniature fuses - Part 6: Fuse-holders for miniature fuse-links |
| IEC 60598-2-17:2017 | Luminaires - Part 2-17: Particular requirements - Luminaires for stage lighting, television and film studios (outdoor and indoor) |
| IEC GUIDE 112:2017 | Guide on the safety of multimedia equipment |
| CSA C22.2 No. 49 : 2014 | FLEXIBLE CORDS AND CABLES |
| IEC 61558-2-4:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers |
| IEC 61293:1994 | Marking of electrical equipment with ratings related to electrical supply - Safety requirements |
| CSA C22.2 No. 0.4 : 2004(R2013) | BONDING OF ELECTRICAL EQUIPMENT |
| IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV | Plugs and socket-outlets for household and similar purposes - Part1: General requirements |
| IEC TR 60083:2015 | Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC |
| ISO 9773:1998 | Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source |
| IEC 60169-3:1965 | Radio-frequency connectors - Part 3: Two-pin connector for twin balanced aerial feeders |
| IEC 60999-2:2003 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included) |
| CSA C22.2 No. 21 : 2014 | CORD SETS AND POWER-SUPPLY CORDS |
| IEC 62151:2000 | Safety of equipment electrically connected to a telecommunication network |
| CSA C22.2 No. 24 : 2015 | TEMPERATURE-INDICATING AND -REGULATING EQUIPMENT |
| IEC 60169-2:1965 | Radio-frequency connectors. Part 2: Coaxial unmatched connector |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| IEC 60130-9:2011 | Connectors for frequencies below 3 MHz - Part 9: Circular connectors for radio and associated sound equipment |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 60384-1:2016 | Fixed capacitors for use in electronic equipment - Part 1: Generic specification |
| IEC 60227-2:1997+AMD1:2003 CSV | Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 2: Test methods |
| IEEE C57.12.00-2015 | IEEE Standard for General Requirements for Liquid-Immersed Distribution, Power, and Regulating Transformers |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| IEC 60068-2-31:2008 | Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens |
| CSA C22.2 No. 60691 : 2015 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE |
| IEC 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| IEC 60851-5:2008+AMD1:2011 CSV | Winding wires - Test methods - Part 5: Electrical properties |
| CSA C22.2 No. 269.5 : 2015 | SURGE PROTECTIVE DEVICES - TYPE 5 - COMPONENTS |
| IEC 60999-1:1999 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
| IEC 60167:1964 | Methods of test for the determination of the insulation resistance of solid insulating materials |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| IEC 60320-2-2:1998 | Appliance couplers for household and similar general purposes - Part 2-2: Interconnection couplers for household and similar equipment |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| IEC 60998-2-2:2002 | Connecting devices for low-voltage circuits for household and similar purposes - Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units |
| ISO/IEC Guide 37:2012 | Instructions for use of products by consumers |
| CSA E60730.1 : 2015 | Automatic electrical controls for household and similar use — Part 1: General requirements |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| IEC 60691:2015 | Thermal-links - Requirements and application guide |
| IEC GUIDE 104:2010 | The preparation of safety publications and the use of basic safety publications and group safety publications |
| CSA C22.2 No. 0.15 : 2015 | ADHESIVE LABELS |
| C22.2 NO. 8-13 (R2018) | Electromagnetic interference (EMI) filters |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| IEC 61051-2:1991 | Varistors for use in electronic equipment - Part 2: Sectional specification for surge suppression varistors |
| IEC 60906-1:2009 | IEC system of plugs and socket-outlets for household and similar purposes - Part 1: Plugs and socket-outlets 16 A 250 V a.c. |
| CSA C22.2 No. 210 : 2015 | APPLIANCE WIRING MATERIAL PRODUCTS |
| CSA C22.2 No. 127 : 2015 | EQUIPMENT AND LEAD WIRES |
| IEC 60851-3:2009+AMD1:2013 CSV | Winding wires - Test methods - Part 3: Mechanical properties |
| IEC 60268-1:1985 | Sound system equipment. Part 1: General |
| IEC 62471:2006 | Photobiological safety of lamps and lamp systems |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 61965:2003 | Mechanical safety of cathode ray tubes |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 60747-5-5:2007+AMD1:2013 CSV | Semiconductor devices - Discrete devices - Part 5-5: Optoelectronic devices - Photocouplers |
| IEC 60086-4:2014 | Primary batteries - Part 4: Safety of lithium batteries |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| IEC 60317-43:1997+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 43: Aromatic polyimide type wrapped round copper wire, class 240 |
| CSA C22.2 No. 55 : 2015 | SPECIAL USE SWITCHES |
| IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
| IEC 61260:1995 | Electroacoustics - Octave-band and fractional-octave-band filters |
| IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 62368-1:2014 | Audio/video, information and communication technology equipment - Part 1: Safety requirements |
| IEC 60335-2-56:2002+AMD1:2008+AMD2:2014 CSV | Household and similar electrical appliances - Safety - Part 2-56:Particular requirements for projectors and similar appliances |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| CSA C22.2 No. 94.2 : 2015 | ENCLOSURES FOR ELECTRICAL EQUIPMENT, ENVIRONMENTAL CONSIDERATIONS |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.