EN 228:2012+A1:2017
Current
Current
The latest, up-to-date edition.
Automotive fuels - Unleaded petrol - Requirements and test methods
Published date
31-05-2017
Publisher
Sorry this product is not available in your region.
European foreword
1 Scope
2 Normative references
3 Sampling
4 Pump marking
5 Requirements and test methods
Annex A (normative) - Vapour pressure waiver
Bibliography
This European Standard specifies requirements and test methods for marketed and delivered unleaded petrol. It is applicable to unleaded petrol for use in petrol engine vehicles designed to run on unleaded petrol.This European Standard specifies two types of unleaded petrol: one type with a maximum oxygen content of 3,7 % (m/m) and a maximum ethanol content of 10,0 % (V/V) in Table 1, and one type intended for older vehicles that are not warranted to use unleaded petrol with a high biofuel content, with a maximum oxygen content of 2,7 % (m/m) and a maximum ethanol content of 5,0 % (V/V) in Table 2.NOTE 1The two types are based on European Directive requirements [3], [4], ![11]".NOTE 2For the purposes of this European Standard, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction, µ, and the volume fraction, φ.
| Committee |
CEN/TC 19
|
| DevelopmentNote |
Supersedes PREN 228. (11/2012) 2012 Edition Re-Issued in May 2017 & incorporates AMD 1 2017. (06/2017)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| ONORM EN 228 : 2017 | Identical |
| I.S. EN 228:2017 | Identical |
| NF EN 228 : 2013 + A1 2018 | Identical |
| DIN EN 228:2017-08 | Identical |
| BS EN 228 : 2012 | Identical |
| I.S. EN 228:2012 | Identical |
| SN EN 228+A1:2018 | Identical |
| UNI EN 228 : 2013 | Identical |
| DIN EN 228 Berichtigung 1:2020-08 | Identical |
| NBN EN 228 : 2012 | Identical |
| PN EN 228 : 2013 + A1 2017 | Identical |
| NS EN 228 : 2012 + A1 2017 | Identical |
| UNI EN 228:2017 | Identical |
| BS EN 228:2012+A1:2017 | Identical |
| I.S. EN 228:2012+A1:2017 | Identical |
| NEN EN 228 : 2012 + A1 2017 | Identical |
| ÖNORM EN 228:2020 09 15 | Identical |
| UNE-EN 228:2013+A1:2017 | Identical |
| BS EN 228:2012+A1:2017 | Identical |
| UNE-EN 228:2013 | Identical |
| UNE 51228:1989 | Identical |
| BS EN 228:2012/A1:2017 | Identical |
| DIN EN 228:2004-03 | Identical |
| ISO 19453-5:2018 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment for drive system of electric propulsion vehicles — Part 5: Chemical loads |
| 13/30275105 DC : 0 | BS EN 15376 - AUTOMOTIVE FUELS - ETHANOL AS A BLENDING COMPONENT FOR PETROL - REQUIREMENTS AND TEST METHODS |
| UNE-EN 50620:2017 | Electric cables - Charging cables for electric vehicles |
| I.S. CEN TR 15367-3:2009 | PETROLEUM PRODUCTS - GUIDE FOR GOOD HOUSEKEEPING - PART 3: PREVENTION OF CROSS CONTAMINATION |
| 10/30219414 DC : 0 | BS EN 13617-4 - PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| BS 2000-508(2013) : 2013 COR 2015 | AUTOMOTIVE FUELS - ASSESSMENT OF PETROL AND DIESEL QUALITY - FUEL QUALITY MONITORING SYSTEM (FQMS) |
| S.R. CEN/TR 16569:2013 | AUTOMOTIVE FUELS - ASSESSING THE EFFECTS OF E10 PETROL ON VEHICLE EMISSIONS AND PERFORMANCE |
| 11/30238497 DC : 0 | BS EN 13160-5 - LEAK DETECTION SYSTEMS - PART 5: TANK GAUGE LEAK DETECTION SYSTEMS |
| I.S. EN 14517:2004 | LIQUID PETROLEUM PRODUCTS - DETERMINATION OF HYDROCARBON TYPES AND OXYGENATES IN PETROL - MULTIDIMENSIONAL GAS CHROMATOGRAPHY METHOD |
| CEN/TR 15120:2013 | Tanks for transport of dangerous goods - Guidance and recommendations for loading, transport and unloading |
| 10/30229703 DC : 0 | BS EN ISO 2812-3 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM |
| BS EN 16761-1:2015 | Automotive fuels. Determination of methanol in automotive ethanol (E85) fuel by gas chromatography Method using single column technique |
| S.R. CEN TR 15367-2:2007 | PETROLEUM PRODUCTS - GUIDE FOR GOOD HOUSEKEEPING - PART 2: AUTOMOTIVE PETROL FUELS |
| 02/709495 DC : DRAFT JULY 2002 | EN 13617-4 - PETROL FILLING STATIONS - PART 4: SAFETY AND ENVIRONMENTAL REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| BS 7800:1992 | Specification for high octane (super) unleaded petrol (gasoline) for motor vehicles |
| 13/30279896 DC : 0 | BS ISO 8178-5 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 5: TEST FUELS |
| 14/30294038 DC : 0 | BS EN 16270 - AUTOMOTIVE FUELS - DETERMINATION OF HIGH-BOILING COMPONENTS INCLUDING FATTY ACID METHYL ESTERS IN PETROL AND ETHANOL (E85) AUTOMOTIVE FUEL - GAS CHROMATOGRAPHY METHOD |
| PD CEN/TR 15139:2005 | Petroleum products and other liquids. Applicability of test methods on sulfur determination in petrol and diesel fuel |
| BS 2000-606(2015) : 2015 | AUTOMOTIVE FUELS - DETERMINATION OF HIGH-BOILING COMPONENTS INCLUDING FATTY ACID METHYL ESTERS IN PETROL AND ETHANOL (E85) AUTOMOTIVE FUEL - GAS CHROMATOGRAPHIC METHOD |
| BS EN 19694-5:2016 | Stationary source emissions. Determination of greenhouse gas (GHG) emissions in energy-intensive industries Lime industry |
| BS ISO 19453-5:2018 | Road vehicles. Environmental conditions and testing for electrical and electronic equipment for drive system of electric propulsion vehicles Chemical loads |
| DD CEN/TS 15293:2011 | Automotive fuels. Ethanol (E85) automotive fuel. Requirements and test methods |
| IP 606 : 2016 | AUTOMOTIVE FUELS - DETERMINATION OF HIGH-BOILING COMPONENTS INCLUDING FATTY ACID METHYL ESTERS IN PETROL AND ETHANOL (E85) AUTOMOTIVE FUEL - GAS CHROMATOGRAPHIC METHOD |
| PREN 13483 : DRAFT 2011 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| I.S. CEN TR 15120:2005 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - GUIDANCE AND RECOMMENDATIONS FOR LOADING, TRANSPORT AND UNLOADING |
| PREN 13160-7 : DRAFT 2014 | LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
| UNI EN 16321-1 : 2013 | PETROL VAPOUR RECOVERY DURING REFUELLING OF MOTOR VEHICLES AT SERVICE STATIONS - PART 1: TEST METHODS FOR THE TYPE APPROVAL EFFICIENCY ASSESSMENT OF PETROL VAPOUR RECOVERY SYSTEMS |
| S.R. CEN/TR 15745:2015 | LIQUID PETROLEUM PRODUCTS - DETERMINATION OF HYDROCARBON TYPES AND OXYGENATES VIA MULTIDIMENSIONAL GAS CHROMATOGRAPHY METHOD - ROUND ROBIN RESEARCH REPORT |
| I.S. EN 50620:2017 | ELECTRIC CABLES - CHARGING CABLES FOR ELECTRIC VEHICLES |
| I.S. EN ISO 2812-4:2017 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 4: SPOTTING METHODS (ISO 2812-4:2017) |
| ISO/TR 19441:2018 | Petroleum products Density versus temperature relationships of current fuels, biofuels and biofuel components |
| BS ISO 8178-5:2008 | Reciprocating internal combustion engines. Exhaust emission measurement Test fuels |
| UNE-EN ISO 2812-3:2013 | Paints and varnishes - Determination of resistance to liquids - Part 3: Method using an absorbent medium (ISO 2812-3:2012) |
| BS 2000-508(2003) : 2003 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - AUTOMOTIVE FUELS - ASSESSMENT OF PETROL AND DIESEL QUALITY - FUEL QUALITY MONITORING SYSTEM (FQMS) |
| EN ISO 2812-3:2012 | Paints and varnishes - Determination of resistance to liquids - Part 3: Method using an absorbent medium (ISO 2812-3:2012) |
| I.S. EN 13016-3:2018 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 3: DETERMINATION OF VAPOUR PRESSURE AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) (TRIPLE EXPANSION METHOD) |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| DIN EN 13483:2013-09 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| EN 13617-4:2012 | Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| UNE-EN 13617-2:2012 | Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers |
| BS EN 14879-2:2006 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Coatings on metallic components |
| UNE-EN 13617-4:2012 | Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| BS EN 14517:2004 | Methods of test for petroleum and its products. BS 2000-526: Liquid petroleum products. Determination of hydrocarbon types and oxygenates in petrol. Multidimensional gas chromatography method |
| BS EN 13160-2:2003 | Leak detection systems Pressure and vacuum systems |
| BS EN 13160-4:2003 | Leak detection systems Liquid and/or vapour sensor systems for use in leakage containments or interstitial spaces |
| BS EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Linings on concrete components |
| DIN EN 14879-4:2008-01 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components |
| DIN EN 14879-2:2007-02 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components |
| CEN/TR 15993:2018 | Automotive fuels - Ethanol (E85) automotive fuel - Background to the parameters required and their respective limits and determination |
| EN 13160-2:2016 | Leak detection systems - Part 2: Requirements and test/assessment methods for pressure and vacuum systems |
| DIN EN 16321-1:2013-12 | PETROL VAPOUR RECOVERY DURING REFUELLING OF MOTOR VEHICLES AT SERVICE STATIONS - PART 1: TEST METHODS FOR THE TYPE APPROVAL EFFICIENCY ASSESSMENT OF PETROL VAPOUR RECOVERY SYSTEMS |
| DIN EN 1601:2017-10 | LIQUID PETROLEUM PRODUCTS - DETERMINATION OF ORGANIC OXYGENATE COMPOUNDS AND TOTAL ORGANICALLY BOUND OXYGEN CONTENT IN UNLEADED PETROL - METHOD BY GAS CHROMATOGRAPHY (O-FID) |
| EN 13352:2012 | Specification for the performance of automatic tank contents gauges |
| EN 13160-7:2016 | Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets |
| EN 13160-4:2016 | Leak detection systems - Part 4: Requirements and test/assessment methods for sensor based leak detection systems |
| BS 2000-606(2012) : 2012 | AUTOMOTIVE FUELS - DETERMINATION OF HIGH-BOILING COMPONENTS INCLUDING FATTY ACID METHYL ESTERS IN PETROL - GAS CHROMATOGRAPHIC METHOD |
| PD CEN/TR 15745:2015 | Liquid petroleum products. Determination of hydrocarbon types and oxygenates via multidimensional gas chromatography method. Round Robin research report |
| DIN EN 16761-1:2016-02 | AUTOMOTIVE FUELS - DETERMINATION OF METHANOL IN AUTOMOTIVE ETHANOL (E85) FUEL BY GAS CHROMATOGRAPHY - PART 1: METHOD USING SINGLE COLUMN TECHNIQUE |
| BS EN 16270:2015 | Automotive fuels. Determination of high-boiling components including fatty acid methyl esters in petrol and ethanol (E85) automotive fuel. Gas chromatographic method |
| PD CEN/TR 16569:2013 | Automotive fuels. Assessing the effects of E10 petrol on vehicle emissions and performance |
| PREN 13016-3 : DRAFT 2016 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 3: DETERMINATION OF VAPOUR PRESSURE AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) (TRIPLE EXPANSION METHOD) |
| BS ISO 16750-5:2010 | Road vehicles. Environmental conditions and testing for electrical and electronic equipment Chemical loads |
| DIN EN 16440-1:2015-05 | TESTING METHODOLOGIES OF REFRIGERATING DEVICES FOR INSULATED MEANS OF TRANSPORT - PART 1: MECHANICAL COOLING DEVICE WITH FORCED AIR CIRCULATION EVAPORATOR WITH OR WITHOUT HEATING DEVICE |
| EN 50620:2017 | Electric cables - Charging cables for electric vehicles |
| 14/30301266 DC : 0 | BS EN 13160-7 - LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
| BS EN 15268:2008 | Petrol filling stations. Safety requirements for the construction of submersible pump assemblies |
| CEN/TR 15745:2015 | Liquid petroleum products - Determination of hydrocarbon types and oxygenates via multidimensional gas chromatography method - Round Robin research report |
| PREN 16761-2 : DRAFT 2014 | AUTOMOTIVE FUELS - DETERMINATION OF METHANOL IN AUTOMOTIVE ETHANOL (E85) FUEL BY GAS CHROMATOGRAPHY - PART 2: METHOD USING HEART CUT TECHNIQUE |
| UNE-EN 16321-1:2014 | Petrol vapour recovery during refuelling of motor vehicles at service stations - Part 1: Test methods for the type approval efficiency assessment of petrol vapour recovery systems |
| I.S. CEN/TR 15139:2005 | PETROLEUM PRODUCTS AND OTHER LIQUIDS - APPLICABILITY OF TEST METHODS ON SULFUR DETERMINATION IN PETROL AND DIESEL FUEL |
| UNI EN 15268 : 2009 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| CEI EN 50620 : 1ED 2017 | ELECTRIC CABLES - CHARGING CABLES FOR ELECTRIC VEHICLES |
| DIN EN ISO 2812-3:2012-10 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM (ISO 2812-3:2012) |
| I.S. EN 15268:2008 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| DIN EN 1601:2016-06 (Draft) | LIQUID PETROLEUM PRODUCTS - DETERMINATION OF ORGANIC OXYGENATE COMPOUNDS AND TOTAL ORGANICALLY BOUND OXYGEN CONTENT IN UNLEADED PETROL - METHOD BY GAS CHROMATOGRAPHY (O-FID) |
| DIN EN 13617-4:2012-05 | Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| DIN EN 13352:2012-06 | Specification for the performance of automatic tank contents gauges |
| DIN EN 13617-1:2012-08 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| DIN EN 14274:2013-05 | Automotive fuels - Assessment of petrol and diesel quality - Fuel quality monitoring system (FQMS); German version EN 14274:2013 |
| UNE-EN 1601:2018 | Liquid petroleum products - Determination of organic oxygenate compounds and total organically bound oxygen content in unleaded petrol - Method by gas chromatography (O-FID) |
| I.S. EN 13160-7:2016 | LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
| EN 16942:2016 | Fuels - Identification of vehicle compatibility - Graphical expression for consumer information |
| I.S. EN 13483:2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| I.S. EN 13617-4:2012 | PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| I.S. EN ISO 8178-5:1998 | RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 5: TEST FUELS |
| I.S. EN 14274:2013 | AUTOMOTIVE FUELS - ASSESSMENT OF PETROL AND DIESEL QUALITY - FUEL QUALITY MONITORING SYSTEM (FQMS) |
| I.S. EN 13617-2:2012 | PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS |
| I.S. EN 13160-2:2016 | LEAK DETECTION SYSTEMS - PART 2: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PRESSURE AND VACUUM SYSTEMS |
| I.S. EN 13160-5:2016 | LEAK DETECTION SYSTEMS - PART 5: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR IN-TANK GAUGE SYSTEMS AND PRESSURISED PIPEWORK SYSTEMS |
| I.S. EN 13617-1:2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| I.S. EN 13352:2012 | SPECIFICATION FOR THE PERFORMANCE OF AUTOMATIC TANK CONTENTS GAUGES |
| I.S. EN 1360:2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| DIN EN 858-1:2002-05 | CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - PART 1: SAFETY AND EMC REQUIREMENTS FOR THE EQUIPMENT FOR THE STORAGE OF BULK MATERIALS IN SILOS, BUNKERS, BINS AND HOPPERS |
| I.S. EN 13160-4:2016 | LEAK DETECTION SYSTEMS - PART 4: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR SENSOR BASED LEAK DETECTION SYSTEMS |
| 10/30227686 DC : 0 | BS EN 13352 - SPECIFICATION FOR THE PERFORMANCE OF AUTOMATIC TANK CONTENTS GAUGES |
| PREN 50620 : DRAFT 2014 | CHARGING CABLES FOR ELECTRIC VEHICLES |
| PD CEN/TR 15367-3:2009 | Petroleum products. Guide for good housekeeping Prevention of cross contamination |
| 14/30300905 DC : 0 | BS EN 16761-2 - AUTOMOTIVE FUELS - DETERMINATION OF METHANOL IN AUTOMOTIVE ETHANOL (E85) FUEL BY GAS CHROMATOGRAPHY - PART 2: METHOD USING HEART CUT TECHNIQUE |
| 01/714408 DC : DRAFT OCT 2001 | ISO/DIS 16750-5 - ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 5: CHEMICAL LOADS |
| BS EN ISO 2812-1:2017 | Paints and varnishes. Determination of resistance to liquids Immersion in liquids other than water |
| 09/30199323 DC : 0 | BS EN 15293 - AUTOMOTIVE FUELS - ETHANOL (E85) AUTOMOTIVE FUEL REQUIREMENTS AND TEST METHODS |
| PREN 13617-1 : DRAFT 2010 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| BS EN 16942:2016 | Fuels. Identification of vehicle compatibility. Graphical expression for consumer information |
| 17/30336601 DC : DRAFT MAR 2017 | BS ISO 19453-5 - ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT FOR DRIVE SYSTEM OF ELECTRIC PROPULSION VEHICLES - PART 5: CHEMICAL LOADS |
| 16/30338252 DC : 0 | BS EN 16942 - FUELS - IDENTIFICATION OF VEHICLE COMPATIBILITY - GRAPHICAL EXPRESSION FOR CONSUMER INFORMATION |
| CEN/TR 16435:2012 | Liquid petroleum products - Oxygenates blending in line with actual EN 228 requirements |
| 16/30339201 DC : 0 | BS EN 1601 - LIQUID PETROLEUM PRODUCTS - DETERMINATION OF ORGANIC OXYGENATE COMPOUNDS AND TOTAL ORGANICALLY BOUND OXYGEN CONTENT IN UNLEADED PETROL - METHOD BY GAS CHROMATOGRAPHY (O-FID) |
| BS EN 16761-2:2015 | Automotive fuels. Determination of methanol in automotive ethanol (E85) fuel by gas chromatography Method using heart cut technique |
| DIN EN 1360:2013-09 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| 10/30219405 DC : 0 | BS EN 13617-1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| 13/30286135 DC : 0 | BS EN 13616-1 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS - REQUIREMENTS AND TEST/ASSESSMENT METHODS - PART 1: OVERFILL PREVENTION DEVICES WITH CLOSURE DEVICE |
| 14/30301263 DC : 0 | BS EN 13160-5 - LEAK DETECTION SYSTEMS - PART 5: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR IN-TANK GAUGE SYSTEMS AND PRESSURISED PIPEWORK SYSTEMS |
| MIL-STD-3004 Revision D:2014 | QUALITY ASSURANCE/SURVEILLANCE FOR FUELS, LUBRICANTS AND RELATED PRODUCTS |
| BS EN ISO 2812-4:2017 | Paints and varnishes. Determination of resistance to liquids Spotting methods |
| UNE-EN 16761-1:2016 | Automotive fuels - Determination of methanol in automotive ethanol (E85) fuel by gas chromatography - Part 1: Method using single column technique |
| I.S. EN 16761-2:2015 | AUTOMOTIVE FUELS - DETERMINATION OF METHANOL IN AUTOMOTIVE ETHANOL (E85) FUEL BY GAS CHROMATOGRAPHY - PART 2: METHOD USING HEART CUT TECHNIQUE |
| I.S. EN ISO 22854:2016 | LIQUID PETROLEUM PRODUCTS - DETERMINATION OF HYDROCARBON TYPES AND OXYGENATES IN AUTOMOTIVE-MOTOR GASOLINE AND IN ETHANOL (E85) AUTOMOTIVE FUEL - MULTIDIMENSIONAL GAS CHROMATOGRAPHY METHOD (ISO 22854:2016) |
| UNI CEN/TR 15367-3 : 2009 | PETROLEUM PRODUCTS - GUIDE FOR GOOD HOUSEKEEPING - PART 3: PREVENTION OF CROSS CONTAMINATION |
| S.R. CEN/TR 15120:2013 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - GUIDANCE AND RECOMMENDATIONS FOR LOADING, TRANSPORT AND UNLOADING |
| EN 13016-1:2018 | Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE) |
| ISO 4259-2:2017 | Petroleum and related products — Precision of measurement methods and results — Part 2: Interpretation and application of precision data in relation to methods of test |
| I.S. EN 16761-1:2015 | AUTOMOTIVE FUELS - DETERMINATION OF METHANOL IN AUTOMOTIVE ETHANOL (E85) FUEL BY GAS CHROMATOGRAPHY - PART 1: METHOD USING SINGLE COLUMN TECHNIQUE |
| I.S. EN 13016-1:2007 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) |
| PREN 13160-5 : DRAFT 2014 | LEAK DETECTION SYSTEMS - PART 5: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR IN-TANK GAUGE SYSTEMS AND PRESSURISED PIPEWORK SYSTEMS |
| UNI EN ISO 2812-3 : 2012 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM |
| ISO 2812-4:2017 | Paints and varnishes — Determination of resistance to liquids — Part 4: Spotting methods |
| ISO 8178-5:2015 | Reciprocating internal combustion engines Exhaust emission measurement Part 5: Test fuels |
| UNE-EN 13160-7:2017 | Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets |
| DIN EN 13617-2:2012-05 | Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers |
| BS EN 13617-4:2012 | Petrol filling stations Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| ISO 2812-1:2017 | Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water |
| UNE-EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification |
| EN ISO 8178-5 : 1997 | RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - TEST FUELS |
| UNI EN 13617-1 : 2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| UNI EN 14274 : 2013 | AUTOMOTIVE FUELS - ASSESSMENT OF PETROL AND DIESEL QUALITY - FUEL QUALITY MONITORING SYSTEM (FQMS) |
| EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification |
| UNI EN 1360 : 2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| UNI EN 13483 : 2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| EN ISO 2812-1:2017 | Paints and varnishes - Determination of resistance to liquids - Part 1: Immersion in liquids other than water (ISO 2812-1:2017) |
| PD CEN/TR 15993:2013 | Automotive fuels. Ethanol (E85) automotive fuel. Background to the parameters required and their respective limits and determination |
| 14/30303607 DC : 0 | BS EN ISO 19694-5 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF GREENHOUSE GAS (GHG) EMISSIONS IN ENERGY-INTENSIVE INDUSTRIES - PART 5: LIME INDUSTRY |
| PD CEN/TR 15367-2:2007 | Petroleum products. Guide for good housekeeping Automotive petrol fuels |
| IP 508 : 2016 | AUTOMOTIVE FUELS - ASSESSMENT OF PETROL AND DIESEL QUALITY - FUEL QUALITY MONITORING SYSTEM (FQMS) |
| DIN EN 13016-1:2007-11 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT |
| 12/30263877 DC : 0 | BS EN ISO 22854 - LIQUID PETROLEUM PRODUCTS - DETERMINATION OF HYDROCARBON TYPES AND OXYGENATES IN AUTOMOTIVE-MOTOR GASOLINE - MULTIDIMENSIONAL GAS CHROMATOGRAPHY METHOD |
| BS EN 50620:2017 | Electric cables. Charging cables for electric vehicles (BT(DE/NOT)259) |
| BS EN 16321-1:2013 | Petrol vapour recovery during refuelling of motor vehicles at service stations Test methods for the type approval efficiency assessment of petrol vapour recovery systems |
| 11/30250273 DC : 0 | BS EN 13483 - RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| 10/30219408 DC : 0 | BS EN 13617-2 - PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS |
| S.R. CEN/TR 15993:2018 | AUTOMOTIVE FUELS - ETHANOL (E85) AUTOMOTIVE FUEL - BACKGROUND TO THE PARAMETERS REQUIRED AND THEIR RESPECTIVE LIMITS AND DETERMINATION |
| UNE-EN 16942:2016 | Fuels - Identification of vehicle compatibility - Graphical expression for consumer information |
| 08/30173385 DC : DRAFT JULY 2008 | BS ISO 16750-5 - ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 5: CHEMICAL LOADS |
| BS EN 16440-1:2015 | Testing methodologies of refrigerating devices for insulated means of transport Mechanical cooling device with forced air circulation evaporator with or without heating device |
| 01/704739 DC : DRAFT FEB 2001 | PREN 14125 - UNDERGROUND PIPEWORK FOR PETROL FILLING STATIONS |
| MIL-PRF-370 Revision K:2017 | HOSE AND HOSE ASSEMBLIES, NONMETALLIC: ELASTOMERIC, LIQUID FUEL |
| DIN EN 15268:2008-11 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP |
| 11/30249593 DC : 0 | BS EN 16321-1 - PETROL VAPOUR RECOVERY DURING REFUELLING OF MOTOR VEHICLES AT SERVICE STATIONS - PART 1: TEST METHODS FOR THE TYPE APPROVAL EFFICIENCY ASSESSMENT OF VAPOUR RECOVERY SYSTEMS |
| EI GUID. STORAGE AND HANDLING BIOFUELS : 1ED 2017 | GUIDANCE FOR THE STORAGE AND HANDLING OF BIOFUELS AT FILLING STATIONS |
| DIN 51413-7:1990-05 | TESTING OF LIQUID MINERAL OIL HYDROCARBONS - ANALYSIS BY GAS CHROMATOGRAPHY - DETERMINATION OF OXYGENATES AND THE OXYGEN CONTENT - PROCEDURE BY OXYGEN-SPECIFIC DETECTOR (O-FID) |
| UNE-EN 16270:2015 | Automotive fuels - Determination of high-boiling components including fatty acid methyl esters in petrol and ethanol (E85) automotive fuel - Gas chromatographic method |
| UNE-EN 15376:2015 | Automotive fuels - Ethanol as a blending component for petrol - Requirements and test methods |
| PREN 13617-2 : DRAFT 2010 | PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS |
| S.R. CEN TS 15293:2011 | AUTOMOTIVE FUELS - ETHANOL (E85) AUTOMOTIVE FUEL - REQUIREMENTS AND TEST METHODS |
| BS EN ISO 4259-2:2017 | Petroleum and related products. Precision of measurement methods and results Interpretation and application of precision data in relation to methods of test |
| EN ISO 4259-2:2017 | Petroleum and related products - Precision of measurement methods and results - Part 2: Interpretation and application of precision data in relation to methods of test (ISO 4259-2:2017) |
| EN ISO 22854:2016 | Liquid petroleum products - Determination of hydrocarbon types and oxygenates in automotive-motor gasoline and in ethanol (E85) automotive fuel - Multidimensional gas chromatography method (ISO 22854:2016) |
| S.R. CEN/TR 16514:2013 | AUTOMOTIVE FUELS - UNLEADED PETROL CONTAINING MORE THAN 3,7% (M/M) OXYGEN - ROADMAP, TEST METHODS, AND REQUIREMENTS FOR E10+ PETROL |
| PREN 1601 : DRAFT 2016 | LIQUID PETROLEUM PRODUCTS - DETERMINATION OF ORGANIC OXYGENATE COMPOUNDS AND TOTAL ORGANICALLY BOUND OXYGEN CONTENT IN UNLEADED PETROL - METHOD BY GAS CHROMATOGRAPHY (O-FID) |
| BS EN 13016-1:2007 | Liquid petroleum products. Vapour pressure Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE) |
| BS 2000-408(2014) : 2014 COR 2014 | LIQUID PETROLEUM PRODUCTS - UNLEADED PETROL - DETERMINATION OF ORGANIC OXYGENATE COMPOUNDS AND TOTAL ORGANICALLY BOUND OXYGEN CONTENT BY GAS CHROMATOGRAPHY (O-FID) |
| BS 2000-394(2007) : 2007 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) |
| 16/30336428 DC : 0 | BS EN 15293 - AUTOMOTIVE FUELS - ETHANOL (E85) AUTOMOTIVE FUEL - REQUIREMENTS AND TEST METHODS |
| CEN/TR 15367-2:2007 | Petroleum products - Guide for good housekeeping - Part 2: Automotive petrol fuels |
| BS EN ISO 2812-3:2012 | Paints and varnishes. Determination of resistance to liquids Method using an absorbent medium |
| UNE-EN ISO 2812-4:2018 | Paints and varnishes - Determination of resistance to liquids - Part 4: Spotting methods (ISO 2812-4:2017) |
| PREN 15293 : DRAFT 2016 | AUTOMOTIVE FUELS - ETHANOL (E85) AUTOMOTIVE FUEL - REQUIREMENTS AND TEST METHODS |
| ISO 16750-5:2010 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 5: Chemical loads |
| EN 13617-2:2012 | Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers |
| I.S. EN 15376:2014 | AUTOMOTIVE FUELS - ETHANOL AS A BLENDING COMPONENT FOR PETROL - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 2812-3:2012 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM (ISO 2812-3:2012) |
| I.S. EN ISO 4259-2:2017 | PETROLEUM AND RELATED PRODUCTS - PRECISION OF MEASUREMENT METHODS AND RESULTS - PART 2: INTERPRETATION AND APPLICATION OF PRECISION DATA IN RELATION TO METHODS OF TEST (ISO 4259-2:2017) |
| ISO 22854:2016 | Liquid petroleum products Determination of hydrocarbon types and oxygenates in automotive-motor gasoline and in ethanol (E85) automotive fuel Multidimensional gas chromatography method |
| BS EN 13160-5:2004 | Leak detection systems Tank gauge leak detection systems |
| UNE-EN 13160-2:2017 | Leak detection systems - Part 2: Requirements and test/assessment methods for pressure and vacuum systems |
| BS EN 13160-7:2003 | Leak detection systems General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jackets |
| BS EN 13617-1:2012 | Petrol filling stations Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 14879-4:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Linings on metallic components |
| BS EN 14879-3:2006 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Coatings on concrete components |
| UNE-EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems. Specification |
| BS EN ISO 8178-5:1997 | Reciprocating internal combustion engines. Exhaust emission measurement Test fuels |
| UNE-EN 13352:2012 | Specification for the performance of automatic tank contents gauges |
| UNE-EN ISO 2812-1:2018 | Paints and varnishes - Determination of resistance to liquids - Part 1: Immersion in liquids other than water (ISO 2812-1:2017) |
| EN 1601:2017 | Liquid petroleum products - Determination of organic oxygenate compounds and total organically bound oxygen content in unleaded petrol - Method by gas chromatography (O-FID) |
| EN 14879-3:2006 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 3: Coatings on concrete components |
| UNI EN 13617-4 : 2012 | PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| EN 14879-2:2006 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components |
| UNI EN 13617-2 : 2012 | PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS |
| EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| EN 16321-1:2013 | Petrol vapour recovery during refuelling of motor vehicles at service stations - Part 1: Test methods for the type approval efficiency assessment of petrol vapour recovery systems |
| EN 16270:2015 | Automotive fuels - Determination of high-boiling components including fatty acid methyl esters in petrol and ethanol (E85) automotive fuel - Gas chromatographic method |
| EN 14517:2004 | Liquid petroleum products - Determination of hydrocarbon types and oxygenates in petrol - Multidimensional gas chromatography method |
| EN 15268:2008 | Petrol filling stations - Safety requirements for the construction of submersible pump assemblies |
| EN 15376:2014 | Automotive fuels - Ethanol as a blending component for petrol - Requirements and test methods |
| EN 16761-1:2015 | Automotive fuels - Determination of methanol in automotive ethanol (E85) fuel by gas chromatography - Part 1: Method using single column technique |
| EN 16440-1:2015 | Testing methodologies of refrigerating devices for insulated means of transport - Part 1: Mechanical cooling device with forced air circulation evaporator with or without heating device |
| EN 19694-5:2016 | Stationary source emissions - Determination of greenhouse gas (GHG) emissions in energy-intensive industries - Part 5: Lime industry |
| EN 16761-2:2015 | Automotive fuels - Determination of methanol in automotive ethanol (E85) fuel by gas chromatography - Part 2: Method using heart cut technique |
| EN 14879-4:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components |
| DIN EN 16270:2015-08 | AUTOMOTIVE FUELS - DETERMINATION OF HIGH-BOILING COMPONENTS INCLUDING FATTY ACID METHYL ESTERS IN PETROL AND ETHANOL (E85) AUTOMOTIVE FUEL - GAS CHROMATOGRAPHIC METHOD |
| 09/30206695 DC : 0 | BS EN 15376 - AUTOMOTIVE FUELS - ETHANOL AS A BLENDING COMPONENT FOR PETROL - REQUIREMENTS AND TEST METHODS |
| PREN 13617-4 : DRAFT 2010 | PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| PD CEN/TR 16514:2013 | Automotive fuels. Unleaded petrol containing more than 3,7 % (m/m) oxygen. Roadmap, test methods, and requirements for E10+ petrol |
| 14/30300902 DC : 0 | BS EN 16761-1 - AUTOMOTIVE FUELS - DETERMINATION OF METHANOL IN AUTOMOTIVE ETHANOL (E85) FUEL BY GAS CHROMATOGRAPHY - PART 1: METHOD USING SINGLE COLUMN TECHNIQUE |
| UNE-EN 16440-1:2015 | Testing methodologies of refrigerating devices for insulated means of transport - Part 1: Mechanical cooling device with forced air circulation evaporator with or without heating device |
| I.S. EN 16321-1:2013 | PETROL VAPOUR RECOVERY DURING REFUELLING OF MOTOR VEHICLES AT SERVICE STATIONS - PART 1: TEST METHODS FOR THE TYPE APPROVAL EFFICIENCY ASSESSMENT OF PETROL VAPOUR RECOVERY SYSTEMS |
| 14/30288755 DC : 0 | BS EN 50620 - CHARGING CABLES FOR ELECTRIC VEHICLES |
| CEN/TR 16569:2013 | Automotive fuels - Assessing the effects of E10 petrol on vehicle emissions and performance |
| PD CEN/TR 15120:2013 | Tanks for transport of dangerous goods. Guidance and recommendations for loading, transport and unloading |
| BS EN ISO 22854:2016 | Liquid petroleum products. Determination of hydrocarbon types and oxygenates in automotive-motor gasoline and in ethanol (E85) automotive fuel. Multidimensional gas chromatography method |
| I.S. EN 1601:2017 | LIQUID PETROLEUM PRODUCTS - DETERMINATION OF ORGANIC OXYGENATE COMPOUNDS AND TOTAL ORGANICALLY BOUND OXYGEN CONTENT IN UNLEADED PETROL - METHOD BY GAS CHROMATOGRAPHY (O-FID) |
| I.S. EN 16440-1:2015 | TESTING METHODOLOGIES OF REFRIGERATING DEVICES FOR INSULATED MEANS OF TRANSPORT - PART 1: MECHANICAL COOLING DEVICE WITH FORCED AIR CIRCULATION EVAPORATOR WITH OR WITHOUT HEATING DEVICE |
| UNE-EN ISO 22854:2016 | Liquid petroleum products - Determination of hydrocarbon types and oxygenates in automotive-motor gasoline and in ethanol (E85) automotive fuel - Multidimensional gas chromatography method (ISO 22854:2016) |
| PREN 1360 : DRAFT 2011 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| DIN EN 16761-2:2016-02 | AUTOMOTIVE FUELS - DETERMINATION OF METHANOL IN AUTOMOTIVE ETHANOL (E85) FUEL BY GAS CHROMATOGRAPHY - PART 2: METHOD USING HEART CUT TECHNIQUE |
| 11/30250270 DC : 0 | BS EN 1360 - RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| DIN EN 15376:2014-12 | AUTOMOTIVE FUELS - ETHANOL AS A BLENDING COMPONENT FOR PETROL - REQUIREMENTS AND TEST METHODS |
| 04/30123574 DC : DRAFT OCT 2004 | EN 14879-3 - ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 3: COATINGS ON CONCRETE COMPONENTS |
| I.S. EN 16942:2016 | FUELS - IDENTIFICATION OF VEHICLE COMPATIBILITY - GRAPHICAL EXPRESSION FOR CONSUMER INFORMATION |
| 16/30327612 DC : 0 | BS EN 13016-3 - LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 3: DETERMINATION OF VAPOUR PRESSURE AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) (TRIPLE EXPANSION METHOD) |
| PD CEN/TR 16435:2012 | Liquid petroleum products. Oxygenates blending in line with actual EN 228 requirements |
| I.S. EN 16270:2015 | AUTOMOTIVE FUELS - DETERMINATION OF HIGH-BOILING COMPONENTS INCLUDING FATTY ACID METHYL ESTERS IN PETROL AND ETHANOL (E85) AUTOMOTIVE FUEL - GAS CHROMATOGRAPHIC METHOD |
| BS EN 15376:2014 | Automotive fuels. Ethanol as a blending component for petrol. Requirements and test methods |
| S.R. CEN/TR 16435:2012 | LIQUID PETROLEUM PRODUCTS - OXYGENATES BLENDING IN LINE WITH ACTUAL EN 228 REQUIREMENTS |
| CEN/TR 15139:2005 | Petroleum products and other liquids - Applicability of test methods on sulfur determination in petrol and diesel fuel |
| UNE-EN 16761-2:2016 | Automotive fuels - Determination of methanol in automotive ethanol (E85) fuel by gas chromatography - Part 2: Method using heart cut technique |
| CEN/TR 15367-3:2009 | Petroleum products - Guide for good housekeeping - Part 3: Prevention of cross contamination |
| I.S. EN 19694-5:2016 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF GREENHOUSE GAS (GHG) EMISSIONS IN ENERGY-INTENSIVE INDUSTRIES - PART 5: LIME INDUSTRY |
| ISO 2812-3:2012 | Paints and varnishes Determination of resistance to liquids Part 3: Method using an absorbent medium |
| EN 13016-3:2018 | Liquid petroleum products - Vapour pressure - Part 3: Determination of vapour pressure and calculated dry vapour pressure equivalent (DVPE) (Triple Expansion Method) |
| EN ISO 2812-4:2017 | Paints and varnishes - Determination of resistance to liquids - Part 4: Spotting methods (ISO 2812-4:2017) |
| I.S. EN ISO 2812-1:2017 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 1: IMMERSION IN LIQUIDS OTHER THAN WATER (ISO 2812-1:2017) |
| I.S. CWA 15293:2005 | AUTOMOTIVE FUELS - ETHANOL E85 - REQUIREMENTS AND TEST METHODS |
| UNE-EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| UNE-EN 13160-4:2017 | Leak detection systems - Part 4: Requirements and test/assessment methods for sensor based leak detection systems |
| BS EN 13352:2012 | Specification for the performance of automatic tank contents gauges |
| BS EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems. Specification |
| BS EN 14274:2013 | Automotive fuels. Assessment of petrol and diesel quality. Fuel quality monitoring system (FQMS) |
| BS EN 13617-2:2012 | Petrol filling stations Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers |
| UNE-EN 13160-5:2017 | Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems |
| BS EN 1601:2017 | Liquid petroleum products. Determination of organic oxygenate compounds and total organically bound oxygen content in unleaded petrol. Method by gas chromatography (O-FID) |
| BS EN 858-1:2002 | Separator systems for light liquids (e.g. oil and petrol) Principles of product design, performance and testing, marking and quality control |
| CEN/TS 15293:2011 | Automotive fuels - Ethanol (E85) automotive fuel - Requirements and test methods |
| EN 13160-5:2016 | Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems |
| DIN EN 14879-3:2007-02 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 3: Coatings on concrete components |
| DIN EN 14517:2004-12 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - BS 2000-256: LIQUID PETROLEUM PRODUCTS - DETERMINATION OF HYDROCARBON TYPES AND OXYGENATES IN PETROL - MULTIDIMENSIONAL GAS CHROMATOGRAPHY METHOD |
| CEN/TR 16514:2013 | Automotive fuels - Unleaded petrol containing more than 3,7 % (m/m) oxygen - Roadmap, test methods, and requirements for E10+ petrol |
| DIN EN 14879-5:2007-10 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| ISO 3171:1988 | Petroleum liquids — Automatic pipeline sampling |
| CEN/TR 16435:2012 | Liquid petroleum products - Oxygenates blending in line with actual EN 228 requirements |
| EN 237:2004 | Liquid petroleum products - Petrol - Determination of low lead concentrations by atomic absorption spectrometry |
| ISO 5164:2014 | Petroleum products — Determination of knock characteristics of motor fuels — Research method |
| EN ISO 5164:2014 | Petroleum products - Determination of knock characteristics of motor fuels - Research method (ISO 5164:2014) |
| EN 14275:2013 | Automotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers |
| CEN/TR 15745:2015 | Liquid petroleum products - Determination of hydrocarbon types and oxygenates via multidimensional gas chromatography method - Round Robin research report |
| CEN/TR 15367-3:2009 | Petroleum products - Guide for good housekeeping - Part 3: Prevention of cross contamination |
| EN 1601:2017 | Liquid petroleum products - Determination of organic oxygenate compounds and total organically bound oxygen content in unleaded petrol - Method by gas chromatography (O-FID) |
| ISO 3170:2004 | Petroleum liquids — Manual sampling |
| EN 16135:2011 | Automotive fuels - Determination of manganese content in unleaded petrol - Flame atomic absorption spectrometric method (FAAS) |
| ISO 22854:2016 | Liquid petroleum products Determination of hydrocarbon types and oxygenates in automotive-motor gasoline and in ethanol (E85) automotive fuel Multidimensional gas chromatography method |
| ISO 3675:1998 | Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method |
| EN ISO 6246:2017 | Petroleum products - Gum content of fuels - Jet evaporation method (ISO 6246:2017) |
| ISO 7536:1994 | Petroleum products — Determination of oxidation stability of gasoline — Induction period method |
| EN ISO 12185:1996 | Crude petroleum and petroleum products - Determination of density - Oscillating U-tube method (ISO 12185:1996) |
| CEN/TR 15367-2:2007 | Petroleum products - Guide for good housekeeping - Part 2: Automotive petrol fuels |
| ISO 2160:1998 | Petroleum products Corrosiveness to copper Copper strip test |
| EN ISO 3675:1998 | Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method (ISO 3675:1998) |
| EN 15376:2014 | Automotive fuels - Ethanol as a blending component for petrol - Requirements and test methods |
| EN ISO 13032:2012 | Petroleum products - Determination of low concentration of sulfur in automotive fuels - Energy-dispersive X-ray fluorescence spectrometric method (ISO 13032:2012) |
| EN ISO 3405:2011 | Petroleum products - Determination of distillation characteristics at atmospheric pressure (ISO 3405:2011) |
| ISO 5163:2014 | Petroleum products — Determination of knock characteristics of motor and aviation fuels — Motor method |
| EN 15553:2007 | Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method |
| ISO 12185:1996 | Crude petroleum and petroleum products — Determination of density — Oscillating U-tube method |
| ISO 20884:2011 | Petroleum products Determination of sulfur content of automotive fuels Wavelength-dispersive X-ray fluorescence spectrometry |
| ISO 6246:2017 | Petroleum products — Gum content of fuels — Jet evaporation method |
| EN ISO 22854:2016 | Liquid petroleum products - Determination of hydrocarbon types and oxygenates in automotive-motor gasoline and in ethanol (E85) automotive fuel - Multidimensional gas chromatography method (ISO 22854:2016) |
| ISO 4259:2006 | Petroleum products Determination and application of precision data in relation to methods of test |
| EN 16136:2015 | Automotive fuels - Determination of manganese and iron content in unleaded petrol - Inductively coupled plasma optical emission spectrometry (ICP OES) method |
| EN ISO 7536:1996 | Petroleum products - Determination of oxidation stability of gasoline - Induction period method (ISO 7536:1994) |
| EN 16942:2016 | Fuels - Identification of vehicle compatibility - Graphical expression for consumer information |
| ISO 3405:2011 | Petroleum products Determination of distillation characteristics at atmospheric pressure |
| EN 13132:2000 | Liquid petroleum products - Unleaded petrol - Determination of organic oxygenate compounds and total organically bound oxygen content by gas chromatography using column switching |
| ISO 20846:2011 | Petroleum products Determination of sulfur content of automotive fuels Ultraviolet fluorescence method |
| EN ISO 20884:2011 | Petroleum products - Determination of sulfur content of automotive fuels - Wavelength-dispersive X-ray fluorescence spectrometry (ISO 20884:2011) |
| EN ISO 2160:1998 | Petroleum products - Corrosiveness to copper - Copper strip test (ISO 2160:1998) |
| EN ISO 20846:2011 | Petroleum products - Determination of sulfur content of automotive fuels - Ultraviolet fluorescence method (ISO 20846:2011) |
| EN ISO 5163:2014 | Petroleum products - Determination of knock characteristics of motor and aviation fuels - Motor method (ISO 5163:2014) |
| ISO 13032:2012 | Petroleum products — Determination of low concentration of sulfur in automotive fuels — Energy-dispersive X-ray fluorescence spectrometric method |
| EN ISO 3170:2004 | Petroleum liquids - Manual sampling (ISO 3170:2004) |
| EN ISO 3171:1999 | Petroleum liquids - Automatic pipeline sampling (ISO 3171:1988) |
| EN ISO 4259:2006 | Petroleum products - Determination and application of precision data in relation to methods of test (ISO 4259:2006) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.