EN 476:2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
General requirements for components used in drains and sewers
Superseded date
05-05-2022
Superseded by
Published date
12-01-2011
Publisher
Sorry this product is not available in your region.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Dimensional requirements
6 Performance requirements
7 Test methods
8 Marking, labelling and packaging
Bibliography
This European Standard specifies general requirements for components inside and outside buildings (see EN 12056-1) such as pipes, fittings and manholes with their respective joints intended for use in discharge pipes, drains and sewers which operate as gravity systems allowing for a maximum pressure of 40 kPa.It also specifies general requirements for components used in hydraulically and pneumatically pressurised discharge pipes, drains and sewers. It provides basic specifications to be respected in material related product standards for these applications.It is not applicable for the direct evaluation of products. It is applicable as a reference for drawing up a product specification, if there is no product standard available. NOTEWhere the term "inside buildings" is used in the context of components fixed inside buildings, it also includes discharge pipes and fittings fixed on external surfaces of buildings.This European Standard covers components to be used in conveying in a satisfactory manner:-domestic wastewater;-rainwater and surface water; and-other waste waters acceptable for discharge into the system (e.g. industrial wastewater).This European standard applies to components of circular and other cross sections.This European Standard applies equally to components which are factory-made and to those constructed on site, where applicable.This European Standard does not apply to components used for trenchless construction according to EN 14457 and for components used for renovation of drains and sewers according to EN 13380.
| Committee |
CEN/TC 165
|
| DevelopmentNote |
Supersedes EN 1293 & EN 773. (01/2011)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN 476 : 2011 | Identical |
| I.S. EN 476:2011 | Identical |
| BS EN 476:2011 | Identical |
| NF EN 476 : 2011 | Identical |
| SN EN 476 : 2011 | Identical |
| UNE-EN 476:2011 | Identical |
| DIN EN 476:2011-04 | Identical |
| PN EN 476 : 2012 | Identical |
| UNI EN 476 : 2011 | Identical |
| NS EN 476 : 2011 | Identical |
| NBN EN 476 : 2011 | Identical |
| ONORM EN 476 : 2011 | Identical |
| 16/30329419 DC : 0 | BS EN 12566-1 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 1: PREFABRICATED SEPTIC TANKS |
| PREN 1451-1 : DRAFT 2016 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 12/30254917 DC : DRAFT JAN 2012 | BS EN 877 - CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| PREN 1519-1 : DRAFT 2017 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLENE (PE) - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND THE SYSTEM |
| 16/30336859 DC : 0 | BS EN 1852-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 16/30329416 DC : 0 | BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| DIN EN 15383:2014-02 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
| 16/30332879 DC : 0 | BS EN 1451-1 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 14/30310792 DC : 0 | BS EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS |
| BS EN 16323:2014 | Glossary of wastewater engineering terms |
| ISO 7682:2003 | Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Acrylonitrile-butadiene-styrene (ABS) |
| 06/30148351 DC : 0 | EN 12566-6 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 6: PREFABRICATED TREATMENT UNITS FOR SEPTIC TANK EFFLUENT |
| 09/30198143 DC : 0 | BS ISO 13268 - THERMOPLASTICS PIPING SYSTEMS FOR NON PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS |
| UNE-EN 13598-2:2017 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers |
| PREN 1401-1 : DRAFT 2018 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEMS |
| S.R. CEN/TS 15223:2017 | PLASTICS PIPING SYSTEMS - VALIDATED DESIGN PARAMETERS OF BURIED THERMOPLASTICS PIPING SYSTEMS |
| ISO 19220:2004 | Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Styrene copolymer blends (SAN + PVC) |
| I.S. EN 12566-7:2016 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS |
| UNE-EN 16397-2:2015 | Flexible couplings - Part 2: Characteristics and testing for metal banded flexible couplings, adaptors and bushes |
| I.S. EN 1852-1:2018 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| BS EN 12566-6:2013 | Small wastewater treatment systems for up to 50 PT Prefabricated treatment units for septic tank effluent |
| UNI EN 15383 : 2013-11 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
| I.S. EN 12566-3:2016 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| BS EN 13476-3 : 2007 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B |
| DIN EN 1253-1:2015-03 | GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM |
| BS EN 1566-1:2000 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C) Specification for pipes, fittings and the system |
| UNE-EN 12200-1:2017 | Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| BS EN 274-1:2002 | Waste fittings for sanitary appliances Requirements |
| DIN EN 14982:2011-01 | Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (includes Amendment A1:2010) |
| BS EN 12255-10:2001 | Wastewater treatment plants Safety principles |
| BS EN 877 : 1999 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| BS EN 13564-1:2002 | Anti-flooding devices for buildings Requirements |
| UNE-CEN/TR 1295-3:2011 IN | Structural design of buried pipelines under various conditions of loading - Part 3: Common method |
| BS EN 1253-2:2015 | Gullies for buildings Roof drains and floor gullies without trap |
| I.S. EN 877:2000 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| CEN/TR 12566-2:2005 | Small wastewater treatment systems for up to 50 PT - Part 2: Soil infiltration systems |
| EN 1123-3:2004 | Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building |
| EN 12566-6:2016 | Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent |
| EN 16932-3:2018 | Drain and sewer systems outside buildings - Pumping systems - Part 3: Vacuum systems |
| EN 13508-2:2003+A1:2011 | Investigation and assessment of drain and sewer systems outside buildings - Part 2: Visual inspection coding system |
| EN 12566-7:2016 | Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units |
| EN 12566-3:2016 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| CEN/TR 1295-3:2007 | Structural design of buried pipelines under various conditions of loading - Part 3: Common method |
| EN 12255-10:2000 | Wastewater treatment plants - Part 10: Safety principles |
| UNI EN 877 : 2007 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| DIN EN 14830:2007-01 | Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance |
| EN 12666-1:2005+A1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| DIN EN 13476-2:2007-08 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A |
| EN 12763:2000 | Fibre-cement pipes and fittings for discharge systems for buildings - Dimensions and technical terms of delivery |
| EN 1253-2:2015 | Gullies for buildings - Part 2: Roof drains and floor gullies without trap |
| EN 12566-1:2016 | Small wastewater treatment systems for up to 50 PT - Part 1: Prefabricated septic tanks |
| I.S. EN 14830:2006 | THERMOPLASTICS INSPECTION CHAMBER AND MANHOLE BASES - TEST METHODS FOR BUCKLING RESISTANCE |
| I.S. EN 12255-10:2000 | WASTEWATER TREATMENT PLANTS - PART 10: SAFETY PRINCIPLES |
| I.S. EN 14802:2006 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RESISTANCE AGAINST SURFACE AND TRAFFIC LOADING |
| I.S. CEN/TR 12566-2:2005 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 2: SOIL INFILTRATION SYSTEMS |
| PREN 14364 : DRAFT 2011 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS |
| 02/103343 DC : DRAFT MAY 2002 | PREN 14457 - GENERAL REQUIREMENTS FOR COMPONENTS SPECIFICALLY DESIGNED FOR USE IN TRENCHLESS CONSTRUCTION OF DRAINS AND SEWERS |
| 06/30151317 DC : 0 | BS EN 1124-2 - PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 2: SYSTEMS - DIMENSIONS |
| 15/30327642 DC : 0 | BS EN 13476-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| 05/30131069 DC : DRAFT MAR 2005 | EN 598:2005 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| UNE-EN 14636-1:2010 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints |
| 11/30246452 DC : 0 | BS EN 14758-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 13/30260531 DC : 0 | BS EN 1253-2 - GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP |
| 13/30295203 DC : 0 | BS EN 1610 - CONSTRUCTION AND TESTING OF DRAINS AND SEWERS |
| 17/30364341 DC : 0 | BS EN 1519-1 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLENE (PE) - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND THE SYSTEM |
| BS EN 16397-2:2014 | Flexible couplings Characteristics and testing for metal banded flexible couplings, adaptors and bushes |
| PREN 12566-1 : DRAFT 2015 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 1: PREFABRICATED SEPTIC TANKS |
| 10/30237537 DC : 0 | EN 15383 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
| 05/30132762 DC : 0 | PREN 15229 - PLASTICS PIPING SYSTEMS - PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - PERFORMANCE REQUIREMENTS FOR THERMOPLASTICS MANHOLES AND INSPECTION CHAMBERS |
| 11/30246455 DC : 0 | BS EN 1796 - PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) |
| UNI EN 14364 : 2013 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS |
| PREN 1253-2 : DRAFT 2013 | GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP |
| 07/30165577 DC : 0 | BS EN 1852-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 12/30258203 DC : 0 | BS EN 16397-1 - FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS |
| I.S. EN 16932-1:2018 | DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| PREN 13476-2 : DRAFT 2015 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A |
| ISO 7675:2003 | Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Chlorinated poly(vinyl chloride) (PVC-C) |
| UNE-EN 16397-1:2015 | Flexible couplings - Part 1: Performance requirements |
| I.S. EN 16397-2:2014 | FLEXIBLE COUPLINGS - PART 2: CHARACTERISTICS AND TESTING FOR METAL BANDED FLEXIBLE COUPLINGS, ADAPTORS AND BUSHES |
| UNI EN 1796 : 2013 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) |
| I.S. EN 16323:2014 | GLOSSARY OF WASTEWATER ENGINEERING TERMS |
| I.S. EN 13476-3:2007 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B |
| PREN 1852-1 : DRAFT 2016 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| PREN 752 : DRAFT 2015 | DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT |
| 18/30371677 DC : DRAFT MAY 2018 | BS EN 1401-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEMS |
| EN 1566-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system |
| EN 1565-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system |
| EN 1852-1:2018 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system |
| DIN EN 877:2010-01 | Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance (includes Amendment A1:2006 and Corrigendum AC:2008) |
| DIN EN 14758-1:2012-05 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| NF EN 13598-1 : 2011 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| DIN EN 1123-3:2005-02 | Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in shipbuilding |
| DIN EN 598:2009-10 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods (includes Amendment A1:2009) |
| DIN EN 14364:2013-05 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| BS EN 598 : 2007 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| BS EN 14982 : 2006 | PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS |
| BS EN 13380:2001 | General requirements for components used for renovation and repair of drain and sewer systems outside buildings |
| BS EN 14802:2005 | Plastics piping systems. Thermoplastics shafts or risers for inspection chambers and manholes. Determination of resistance against surface and traffic loading |
| DIN EN 752:2015-10 (Draft) | DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT |
| I.S. EN 13508-2:2003 | INVESTIGATION AND ASSESSMENT OF DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PART 2: VISUAL INSPECTION CODING SYSTEM |
| I.S. EN 1253-2:2015 | GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP |
| I.S. EN 598:2007 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| DIN EN 1796:2013-05 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| I.S. EN 1253-1:2015 | GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM |
| I.S. EN 12200-1:2016 | PLASTICS RAINWATER PIPING SYSTEMS FOR ABOVE GROUND EXTERNAL USE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| I.S. EN 1610:2015 | CONSTRUCTION AND TESTING OF DRAINS AND SEWERS |
| I.S. EN 12566-1:2016 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 1: PREFABRICATED SEPTIC TANKS |
| I.S. EN 1796:2013 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) |
| I.S. EN 14758-1:2012 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| I.S. EN 14364:2013 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS |
| I.S. EN 1253-4:2016 | GULLIES FOR BUILDINGS - PART 4: ACCESS COVERS |
| DIN EN 858-1:2002-05 | CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - PART 1: SAFETY AND EMC REQUIREMENTS FOR THE EQUIPMENT FOR THE STORAGE OF BULK MATERIALS IN SILOS, BUNKERS, BINS AND HOPPERS |
| I.S. EN 12666-1:2006 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| S.R. CEN TR 1295-3:2007 | STRUCTURAL DESIGN OF BURIED PIPELINES UNDER VARIOUS CONDITIONS OF LOADING - PART 3: COMMON METHOD |
| I.S. EN 14982:2006 | PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS |
| UNI EN 14758-1 : 2012 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| I.S. EN 15383:2012 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
| 09/30203912 DC : 0 | BS EN 12566-7 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS |
| 11/30250267 DC : 0 | BS EN 16323 - GLOSSARY OF WASTEWATER ENGINEERING TERMS |
| UNI EN 14636-1 : 2010 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS |
| 06/30124428 DC : 0 | EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY (VINYL CHLORIDE)(PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS |
| UNI EN 16397-1 : 2014 | FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS |
| CEN/TR 1046:2013 | Thermoplastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for underground installation |
| 11/30246458 DC : 0 | BS EN 14364 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS |
| BS EN 14636-2:2009 | Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Manholes and inspection chambers |
| 03/102186 DC : DRAFT AUG 2003 | EN 14758-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-M) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 01/107111 DC : DRAFT SEP 2001 | BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| UNI EN 16323 : 2014 | GLOSSARY OF WASTEWATER ENGINEERING TERMS |
| EN 1796:2013 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| EN 1455-1:1999 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system |
| ISO 7671:2003 | Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Polypropylene (PP) |
| I.S. EN 14636-1:2009 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS |
| I.S. EN 1451-1:2017 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| BS EN 1852-1:2018 | Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene (PP) Specifications for pipes, fittings and the system |
| EN 1451-1:2017 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system |
| EN 13476-3:2018 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B |
| DIN EN 13476-1:2015-11 (Draft) | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| BS EN 13476-2:2007 | Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for pipes and fittings with smooth internal and external surface and the system, Type A |
| UNI EN 16397-2 : 2014 | FLEXIBLE COUPLINGS - PART 2: CHARACTERISTICS AND TESTING FOR METAL BANDED FLEXIBLE COUPLINGS, ADAPTORS AND BUSHES |
| PREN 13476-3 : DRAFT 2015 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B |
| EN 14636-1:2009 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints |
| EN 16932-1:2018 | Drain and sewer systems outside buildings - Pumping systems - Part 1: General requirements |
| DIN EN 1433:2005-09 | DRAINAGE CHANNELS FOR VEHICULAR AND PEDESTRIAN AREAS - CLASSIFICATION, DESIGN AND TESTING REQUIREMENTS, MARKING AND EVALUATION OF CONFORMITY |
| DIN EN 12666-1:2011-11 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system (includes Amendment A1:2011) |
| UNE-EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| BS EN 14830:2006 | Thermoplastics inspection chamber and manhole bases. Test methods for buckling resistance |
| BS EN 588-2:2001 | Fibre-cement pipes for sewers and drains Manholes and inspection chambers |
| BS EN 13598-1:2010 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for ancillary fittings including shallow inspection chambers |
| BS EN 1401-1:2009 | Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system |
| BS EN 1123-3:2004 | Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building |
| UNE-EN 1610:2016 | Construction and testing of drains and sewers |
| EN 13476-2:2018+A1:2020 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A |
| I.S. EN 13598-1:2010 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| EN 16397-1:2014 | Flexible couplings - Part 1: Performance requirements |
| UNI EN 13508-2 : 2011 | INVESTIGATION AND ASSESSMENT OF DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PART 2: VISUAL INSPECTION CODING SYSTEM |
| UNI EN 14982 : 2010 | PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS |
| UNI EN 12666-1 : 2011 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| UNI EN 1401-1 : 2009 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| UNI EN 598 : 2009 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| UNI EN 13598-1 : 2011 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VILYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| DIN EN 16397-2:2015-01 | FLEXIBLE COUPLINGS - PART 2: CHARACTERISTICS AND TESTING FOR METAL BANDED FLEXIBLE COUPLINGS, ADAPTORS AND BUSHES |
| DIN EN 16323:2014-07 | GLOSSARY OF WASTEWATER ENGINEERING TERMS |
| I.S. EN 752:2017 | DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT |
| DIN 1986-3:2004-11 | Drainage systems on private ground - Part 3: Specifications for service and maintenance |
| 15/30317327 DC : 0 | BS EN 16941-1 - ON-SITE NON-POTABLE WATER SYSTEMS - PART 1: SYSTEMS FOR THE USE OF RAINWATER |
| PD CEN/TR 15128:2005 | Survey of European standards for rehabilitation of drain and sewer systems |
| BS ISO 13268:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage. Thermoplastics shafts or risers for inspection chambers and manholes. Determination of ring stiffness |
| I.S. EN 274-1:2002 | WASTE FITTINGS FOR SANITARY APPLIANCES - PART 1: REQUIREMENTS |
| 12/30258206 DC : 0 | BS EN 16397-2 - FLEXIBLE COUPLINGS - PART 2: MATERIALS AND DIMENSIONS FOR METAL BANDED FLEXIBLE COUPLINGS |
| 13/30260528 DC : 0 | BS EN 1253-1 - GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM |
| 09/30203307 DC : DRAFT JULY 2009 | BS EN 14636-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS |
| BS EN 16932-3:2018 | Drain and sewer systems outside buildings. Pumping systems Vacuum systems |
| BS EN 14636-1:2009 | Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Pipes and fittings with flexible joints |
| PREN 14636-2 : DRAFT 2009 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS |
| PREN 13598-2 : DRAFT 2014 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS |
| UNE-EN 12566-6:2017 | Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent |
| PREN 1610 : DRAFT 2013 | CONSTRUCTION AND TESTING OF DRAINS AND SEWERS |
| 98/106709 DC : DRAFT AUG 98 | PREN 12566-3 - SMALL WASTE-WATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTE-WATER TREATMENT PLANTS |
| BS EN 15383 : 2012 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
| BS EN 16397-1:2014 | Flexible couplings Performance requirements |
| 02/121757 DC : DRAFT APR 2002 | BS ISO 19220 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) INSIDE BUILDINGS - STYRENE COPOLYMER BLENDS (SAN + PVC) |
| S.R. CEN/TR 1046:2013 | THERMOPLASTICS PIPING AND DUCTING SYSTEMS - SYSTEMS OUTSIDE BUILDING STRUCTURES FOR THE CONVEYANCE OF WATER OR SEWAGE - PRACTICES FOR UNDERGROUND INSTALLATION |
| I.S. EN 14636-2:2009 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS |
| I.S. EN 16397-1:2014 | FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS |
| ISO 8770:2003 | Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Polyethylene (PE) |
| BS EN 13476-1:2007 | Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) General requirements and performance characteristics |
| ISO 13268:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics shafts or risers for inspection chambers and manholes Determination of ring stiffness |
| PREN 1253-1 : DRAFT 2013 | GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM |
| BS EN 12566-7:2013 | Small wastewater treatment systems for up to 50 PT Prefabricated tertiary treatment units |
| PREN 13476-1 : DRAFT 2015 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLSEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| CEN/TS 15223:2017 | Plastics piping systems - Validated design parameters of buried thermoplastics piping systems |
| PREN 14758-1 : DRAFT 2011 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| UNE-EN 12566-7:2017 | Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units |
| ISO 13272:2011 | Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) and polyethylene (PE) — Specifications for manholes and inspection chambers in traffic areas and underground installations |
| EN 13476-1:2018 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics |
| I.S. EN 1455-1:1999 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND THE SYSTEM |
| DIN EN 13476-2:2015-11 (Draft) | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A |
| UNE-EN 1796:2014 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| BS EN 1124-1:1999 | Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems Requirements, testing, quality control |
| BS EN 12763:2000 | Fibre-cement pipes and fittings for discharge systems for buildings. Dimensions and technical terms of delivery |
| UNE-EN 1253-4:2017 | Gullies for buildings - Part 4: Access covers |
| UNE-EN 12566-3:2017 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| BS EN 1455-1:2000 | Plastics piping systems for soil and waste (low and high temperature) within the building structure. Acrylonitrile-butadiene-styrene (ABS) Specifications for pipes, fittings and the system |
| EN 13598-2:2016 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers |
| BS EN 12566-3 : 2005 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| DIN EN 13598-1:2011-02 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| UNE-EN 13598-1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers |
| BS EN 12200-1:2016 | Plastics rainwater piping systems for above ground external use. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system |
| BS EN 1796:2013 | Plastics piping systems for water supply with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| UNE-EN 12566-1:2017 | Small wastewater treatment systems for up to 50 PT - Part 1: Prefabricated septic tanks |
| BS EN 1253-1:2015 | Gullies for buildings Trapped floor gullies with a depth water seal of at least 50 mm |
| BS EN 12666-1 : 2005 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| BS EN 1610:2015 | Construction and testing of drains and sewers |
| UNE EN 15383 : 0 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
| EN 13598-1:2010 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers |
| BS EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifiers (PP-MD) Specifications for pipes, fittings and the system |
| UNE-EN 14364:2015 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| BS EN 13508-2 : 2003 | INVESTIGATION AND ASSESSMENT OF DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PART 2: VISUAL INSPECTION CODING SYSTEM |
| BS EN 14364:2013 | Plastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints |
| BS EN 1123-1:1999 | Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Requirements, testing, quality control |
| EN 274-1:2002 | Waste fittings for sanitary appliances - Part 1: Requirements |
| EN 588-2:2001 | Fibre cement pipes for drains and sewers - Part 2: Manholes and inspection chambers |
| BS EN 1433:2002 | Drainage channels for vehicular and pedestrian areas. Classification, design and testing requirements, marking and evaluation of conformity |
| EN 15383:2012+A1:2013 | Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers |
| ONORM EN 877 : 2008 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| EN 1401-1:2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 1610:2015 | Construction and testing of drains and sewers |
| EN 752:2017 | Drain and sewer systems outside buildings - Sewer system management |
| EN 16397-2:2014 | Flexible couplings - Part 2: Characteristics and testing for metal banded flexible couplings, adaptors and bushes |
| EN 14457:2004 | General requirements for components specifically designed for use in trenchless construction of drains and sewers |
| EN 14982:2006+A1:2010 | Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness |
| EN 598:2007+A1:2009 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods |
| EN 14830:2006 | Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance |
| EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| EN 14802:2005 | Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading |
| EN 14636-2:2009 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers |
| EN 16323:2014 | Glossary of wastewater engineering terms |
| EN 1671:1997 | Pressure sewerage systems outside buildings |
| 11/30245512 DC : 0 | BS ISO 15398 - SPECIFICATIONS FOR THERMOPLASTICS COVERS AND FRAMES FOR MANHOLES AND INSPECTION CHAMBERS USED IN NON-TRAFFIC AREAS |
| PREN 1796 : DRAFT 2011 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) |
| DIN EN 14636-1:2010-04 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints; German version EN 14636-1:2009 |
| 06/30154044 DC : 0 | EN 12566-7 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS |
| I.S. EN 16932-3:2018 | DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 3: VACUUM SYSTEMS |
| 10/30217319 DC : 0 | BS EN 13598-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| DIN EN 16397-1:2015-01 | FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS |
| DIN EN 13598-2:2016-09 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS |
| DIN EN 14636-2:2010-04 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers |
| UNI EN 14636-2 : 2010 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS |
| I.S. EN 13476-1:2007 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| EN 14364:2013 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| I.S. EN 13598-2:2016 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS |
| 17/30362689 DC : 0 | BS EN 16941-2 - ON-SITE NON-POTABLE WATER SYSTEMS - PART 2: SYSTEMS FOR THE USE OF TREATED GREYWATER |
| 15/30327636 DC : 0 | BS EN 13476-3 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B |
| 15/30327639 DC : 0 | BS EN 13476-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A |
| I.S. EN 12566-6:2016 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 6: PREFABRICATED TREATMENT UNITS FOR SEPTIC TANK EFFLUENT |
| BS EN 13598-2:2009 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for manholes and inspection chambers in traffic areas and deep underground installations |
| DIN EN 13476-3:2015-11 (Draft) | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B |
| BS EN 1451-1:2017 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP) Specifications for pipes, fittings and the system |
| I.S. EN 13476-2:2007 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYLCHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A |
| EN 13476-2:2018 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A |
| UNE-EN 16323:2014 | Glossary of wastewater engineering terms |
| I.S. CEN TR 15128:2005 | SURVEY OF EUROPEAN STANDARDS FOR REHABILITATION OF DRAIN AND SEWER SYSTEMS |
| DIN EN 13508-2:2011-08 | Investigation and assessment of drain and sewer systems outside buildings - Part 2: Visual inspection coding system |
| DIN EN 1401-1:2009-07 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| DIN EN 12200-1:2016-10 | PLASTICS RAINWATER PIPING SYSTEMS FOR ABOVE GROUND EXTERNAL USE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| DIN EN 1253-2:2015-03 | GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP |
| DIN EN 1253-4:2016-07 | GULLIES FOR BUILDINGS - PART 4: ACCESS COVERS |
| I.S. EN 1401-1:2009 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| BS EN 1253-4:2016 | Gullies for buildings Access covers |
| BS EN 14457:2004 | General requirements for components specifically designed for use in trenchless construction of drains and sewers |
| BS EN 1825-1:2004 | Grease separators Principles of design, performance and testing, marking and quality control |
| BS EN 1565-1:2000 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene copolymer blends (SAN + PVC) Specifications for pipes, fittings and the system |
| BS EN 858-1:2002 | Separator systems for light liquids (e.g. oil and petrol) Principles of product design, performance and testing, marking and quality control |
| BS EN 12566-1:2000 | Small wastewater treatment systems for up to 50 PT Prefabricated septic tanks |
| EN 12200-1:2016 | Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 13564-1:2002 | Anti-flooding devices for buildings - Part 1: Requirements |
| CEN/TR 15128:2005 | Survey of European Standards for rehabilitation of drain and sewer systems |
| DIN EN 14802:2006-03 | Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading |
| EN 1253-4:2016 | Gullies for buildings - Part 4: Access covers |
| EN 13380:2001 | General requirements for components used for renovation and repair of drain and sewer systems outside buildings |
| EN 1253-1:2015 | Gullies for buildings - Part 1: Trapped floor gullies with a depth water seal of at least 50 mm |
| DIN EN 14457:2004-09 | General requirements for components specifically designed for use in trenchless construction of drains and sewers |
| DIN EN 1825-1:2004-12 | Grease separators - Part 1: Principles of design, performance and testing, marking and quality control; German version EN 1825-1:2004 |
| DIN EN 274-1:2002-05 | WASTE FITTINGS FOR SANITARY APPLIANCES - PART 1: REQUIREMENTS |
| UNE-EN 12666-1:2006 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| UNE-EN 14982:2007 | Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness |
| UNE-EN 13508-2:2003 | Conditions of drain and sewer systems outside buildings - Part 2: Visual inspection coding system |
| EN 14396:2004 | Fixed ladders for manholes |
| EN 805:2000 | Water supply - Requirements for systems and components outside buildings |
| EN 14801:2006 | Conditions for pressure classification of products for water and wastewater pipelines |
| EN 13380:2001 | General requirements for components used for renovation and repair of drain and sewer systems outside buildings |
| EN 752:2017 | Drain and sewer systems outside buildings - Sewer system management |
| EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control |
| EN 13101:2002 | Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity |
| EN 1085:2007 | Wastewater treatment - Vocabulary |
| EN 14457:2004 | General requirements for components specifically designed for use in trenchless construction of drains and sewers |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.