EN 61036:1996/A1:2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ALTERNATING CURRENT STATIC WATT-HOUR METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2)
01-03-2003
12-01-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
3.1 General definitions
3.2 Definitions related to the functional elements
3.3 Definitions of mechanical elements
3.4 Definitions of insulations
3.5 Definitions of meter quantities
3.6 Definitions of influence quantities
3.7 Definition of tests
4 Requirements
4.1 Standard electrical values
4.2 Mechanical requirements
4.3 Climatic conditions
4.4 Electrical requirements
4.5 Electromagnetic compatibility (EMC)
4.6 Accuracy requirements
5 Tests and test conditions
5.1 General testing procedures
5.2 Tests of mechanical requirements
5.3 Tests of climatic influences
5.4 Tests of electrical requirements
5.5 Tests for electromagnetic compatibility (EMC)
5.6 Tests of accuracy requirements
Annex A (normative) Relationship between ambient air
temperature and relative humidity
Annex B (normative) Test circuit diagram for d.c., even
harmonics, odd harmonics and sub-harmonics
Annex C (normative) Voltage waveform for the tests of
the effect of voltage dips and short interruptions
Annex D (normative) Electromagnet for testing the influence
of externally produced magnetic fields
Annex E (informative) Test schedule
Annex F (normative) Test circuit diagram for the test of
immunity to earth fault
Annex G (normative) Optical test output
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Applies only to newly manufactured static watt-hour meters of accuracy classes 1 and 2, for the measurement of alternating current electrical active energy of a frequency in the range 45 Hz to 65 Hz and to their type tests only.
| Committee |
TC 13
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| CEI EN 61036 : 1997 AMD 1 2001 | Identical |
| IEC 61036:1996+AMD1:2000 CSV | Identical |
| NF EN 61036 : 97 AMD 1 2001 | Identical |
| DIN EN 61036 : 2001 | Identical |
| NBN EN 61036 : 98 AMD 1 2001 | Identical |
| I.S. EN 61036:1997 | Identical |
| VDE 0418-7 : 2001 | Identical |
| SN EN 61036 : 1996 AMD 1 2000 | Identical |
| BS EN 61036:1997 | Identical |
| EN 62053-21:2003 | Identical |
| BS EN 61851-22:2002 | Electric vehicle conductive charging system A.C. electric vehicle charging station |
| I.S. EN 62053-61:1999 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 61: POWER CONSUMPTION AND VOLTAGE REQUIREMENTS |
| EN 61358:1996 | Acceptance inspection for direct connected alternating current static watt-hour meters for active energy (classes 1 and 2) |
| EN 62053-31:1998 | Electricity metering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only) |
| EN 62053-61:1998 | Electricity metering equipment (a.c.) - Particular requirements - Part 61: Power consumption and voltage requirements |
| CEI 13-32 : 2000 | WATT-VAR-HOUR METERS FOR LOW-VOLTAGE THREE-PHASE NETWORKS (INTEGRATED UNITS) PRESETTED FOR PROCESSING AND REMOTE MANAGEMENT OF DATA WITH OR WITHOUT INSERTION OF CURRENT TRANSFORMERS |
| CEI EN 61851-22 : 2003 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: AC ELECTRIC VEHICLE CHARGING STATION |
| 95/214875 DC : 0 | PREN 50222 - STANDARD FOR THE EVALUATION OF MEASUREMENT RESULTS TAKING MEASUREMENT UNCERTAINTY INTO ACCOUNT |
| CEI EN 61358 : 1997 | ACCEPTANCE INSPECTION FOR DIRECT CONNECTED ALTERNATING CURRENTE STATIC WATT-HOUR METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2) |
| BS EN 62053-31:1999 | Electricity metering equipment (a.c.). Particular requirements Pulse output devices for electromechanical and electronic meters (two wires only) |
| CEI EN 62053-31 : 1999 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 31: PULSE OUTPUT DEVICES FOR ELECTROMECHANICAL AND ELECTRONIC METERS (TWO WIRES ONLY) |
| I.S. EN 61358:1997 | ACCEPTANCE INSPECTION FOR DIRECT CONNECTED ALTERNATING CURRENT STATIC WATT-HOUR METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2) |
| CEI EN 62053-61 : 1999 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 61: POWER CONSUMPTION AND VOLTAGE REQUIREMENTS |
| 96/210385 DC : 0 | CLC/BTTF 68-6 (SEC)8 - MEASUREMENT GUIDE FOR VOLTAGE CHARACTERISTICS |
| BS EN 62053-61:1999 | Electricity metering equipment (a.c.). Particular requirements Power consumption and voltage requirements |
| EN 61851-22:2002 | Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station |
| IEC 60038:2009 | IEC standard voltages |
| EN 60687:1992/corrigendum:1993 | ALTERNATING CURRENT STATIC WATT HOUR METERS FOR ACTIVE ENERGY (CLASSES 0.2S AND 0.5S) |
| EN 62053-31:1998 | Electricity metering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only) |
| HD 323.2.5 : 200S1 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST SA - SIMULATED SOLAR RADIATION AT GROUND LEVEL |
| IEC 60068-2-5:2010 | Environmental testing - Part 2-5: Tests - Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing |
| HD 323.2.11 : 200S1 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST KA: SALT MIST |
| EN 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 60695-2-1:1991 | Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
| EN 60387:1992 | Symbols for alternating-current electricity meters |
| IEC 60521:1988 | Class 0.5, 1 and 2 alternating-current watthour meters |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC TR 60736:1982 | Testing equipment for electrical energy meters |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| EN 60521:1995/corrigendum Dec. 1997 | CLASS 0,5, 1 AND 2 ALTERNATING-CURRENT WATTHOUR METERS |
| EN 60514:1995 | Acceptance inspection of Class 2 alternating-current watthour meters |
| IEC 60687:1992 | Alternating current static watt-hour meters for active energy (classes 0,2 S and 0,5 S) |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV | Low-voltage fuses - Part 1: General requirements |
| HD 588.1 : S1 AMD 1 | HIGH VOLTAGE TEST TECHNIQUES - GENERAL DEFINITIONS AND TEST REQUIREMENTS |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| HD 472 S1:1989/AC:2013 | NOMINAL VOLTAGES FOR LOW-VOLTAGE PUBLIC ELECTRICITY SUPPLY SYSTEMS |
| IEC 62053-31:1998 | Electricity metering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only) |
| CISPR 22:2008 | Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement |
| EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| EN 60060-2:2011 | High-voltage test techniques - Part 2: Measuring systems |
| HD 323.2.30 : 200S3 | BASIC ENVIRONMENTAL TESTING PROCEDURES - PART 2: TESTS - TEST DB AND GUIDANCE: DAMP HEAT, CYCLIC (12 + 12-HOUR CYCLE) |
| EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| EN 55022:2010/AC:2011 | INFORMATION TECHNOLOGY EQUIPMENT - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT (CISPR 22:2008) |
| HD 554 : 200S1 | VOLTAGE TRANSFORMERS |
| HD 566 : 200S1 | THERMAL EVALUATION AND CLASSIFICATION OF ELECTRICAL INSULATION |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60044-1:1996+AMD1:2000+AMD2:2002 CSV | Instrument transformers - Part 1: Current transformers |
| HD 323.2.6 : 200S2 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST FC AND GUIDANCE: VIBRATION (SINUSOIDAL) |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| IEC 60417C:1977 | Third supplement. |
| IEC 60359:2001 | Electrical and electronic measurement equipment - Expression of performance |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| EN 60044-1:1999/A2:2003 | INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS |
| EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
| IEC 60186:1987 | Voltage transformers |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| IEC 60387:1992 | Symbols for alternating-current electricity meters |
| HD 243 : S12 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT - INDEX, SURVEY AND COMPILATION OF THE SINGLE SHEETS |
| EN 60269-1:2007/A2:2014 | LOW-VOLTAGE FUSES - PART 1: GENERAL REQUIREMENTS (IEC 60269-1:2006/A2:2014) |
| EN 60721-3-3 : 95 AMD 2 97 | CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.