• I.S. EN 62025-2:2005

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    HIGH FREQUENCY INDUCTIVE COMPONENTS - NON-ELECTRICAL CHARACTERISTICS AND MEASURING METHODS - PART 2: TEST METHODS FOR NON-ELECTRICAL CHARACTERISTICS

    Available format(s):  Hardcopy, PDF

    Superseded date:  12-12-2019

    Language(s):  English

    Published date:  01-01-2005

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Test conditions
      4.1 Standard atmospheric conditions for test
      4.2 Referee conditions
    5 Mechanical characteristics test
      5.1 Body strength test
      5.2 Robustness of termination (electrode)
      5.3 Solderability
      5.4 Resistance to soldering heat
      5.5 Resistance to dissolution of metallization
      5.6 Vibration
      5.7 Resistance to shock
    Annex A (normative) Mounting of surface mounting inductor
            to test printed-circuit board

    Abstract - (Show below) - (Hide below)

    Provides a test method for the non-electrical characteristics of the Surface Mounted Device (SMD) inductors to be used for electronic and telecommunication equipment. Defines methods for measuring mechanical performance only.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 62211 : 2017 INDUCTIVE COMPONENTS - RELIABILITY MANAGEMENT (IEC 62211:2017)
    IEC 61188-5-2:2003 Printed boards and printed board assemblies - Design and use - Part 5-2: Attachment (land/joint) considerations - Discrete components
    HD 323.2.20 : 200S3 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST T - SOLDERING
    IEC 62211:2017 INDUCTIVE COMPONENTS - RELIABILITY MANAGEMENT
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 60068-2-58:2015+AMD1:2017 CSV Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
    IEC 61190-1-2:2014 Attachment materials for electronic assembly - Part 1-2: Requirements for soldering pastes for high-quality interconnects in electronics assembly
    IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
    EN 60068-1 : 2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    EN 60068-2-27 : 2009 ENVIRONMENTAL TESTING - PART 2-27: TESTS - TEST EA AND GUIDANCE: SHOCK
    EN 61188-5-2 : 2003 PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES - DESIGN AND USE - PART 5-2: ATTACHMENT (LAND/JOINT) CONSIDERATIONS - DISCRETE COMPONENTS
    IEC 60068-2-77:1999 Environmental testing - Part 2-77: Tests - Test 77: Body strength and impact shock
    EN 60068-2-21 : 2006 ENVIRONMENTAL TESTING - PART 2-21: TESTS - TEST U: ROBUSTNESS OF TERMINATIONS AND INTEGRAL MOUNTING DEVICES
    EN 60068-2-6 : 2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    EN 60068-2-77 : 1999 ENVIRONMENTAL TESTING - PART 2-77: TESTS - TEST 77: BODY STRENGTH AND IMPACT SHOCK (IEC 60068-2-77:1999)
    EN 61190-1-3:2007/A1:2010 ATTACHMENT MATERIALS FOR ELECTRONIC ASSEMBLY - PART 1-3: REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDER FOR ELECTRONIC SOLDERING APPLICATIONS
    EN 61190-1-2 : 2014 ATTACHMENT MATERIALS FOR ELECTRONIC ASSEMBLY - PART 1-2: REQUIREMENTS FOR SOLDERING PASTES FOR HIGH-QUALITY INTERCONNECTS IN ELECTRONICS ASSEMBLY
    EN 60068-2-45:1992/A1:1993 Environmental testing - Part 2: Tests - Test Xa and guidance: Immersion in cleaning solvents
    IEC 60068-2-69:2017 Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
    IEC 61190-1-3:2007+AMD1:2010 CSV Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective