I.S. EN ISO 11961:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL DRILL PIPE
Hardcopy , PDF
13-12-2018
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Conformance
2.1 Dual citing of normative references
2.2 Units of measurement
3 Normative references
4 Terms, definitions, symbols and abbreviated terms
4.1 Terms and definitions
4.2 Symbols and abbreviated terms
5 Information to be supplied when placing orders for
drill-pipe
6 Requirements for drill-pipe
6.1 General
6.2 Dimensions, masses and connections
6.3 Material requirements
6.4 Process of manufacture for drill-pipe
6.5 Traceability
6.6 Inspection and testing - General
6.7 Testing of welds
6.8 Tensile test
6.9 Hardness test
6.10 Charpy V-notch impact test
6.11 Transverse side-bend test
6.12 Imperfections and defects in drill-pipe
6.13 Visual inspection of the drill-pipe weld zone
6.14 Non-destructive examination of the weld zone
6.15 Marking of drill-pipe
6.16 Minimum facility requirements for drill-pipe
manufacturers
6.17 Documentation requirements of drill-pipe
7 Requirements for drill-pipe body
7.1 Information to be supplied when placing orders for
drill-pipe bodies
7.2 Dimensional and mass requirements
7.3 Material requirements
7.4 Process of manufacture
7.5 Traceability
7.6 Inspection and testing - General
7.7 Testing of chemical composition
7.8 Tensile tests
7.9 Charpy V-notch impact tests
7.10 Drill-pipe-body wall thickness
7.11 Drill-pipe-body length
7.12 Internal upset
7.13 Internal profile
7.14 Straightness
7.15 Upset alignment
7.16 Mass determination
7.17 Imperfections and defects of drill-pipe body
7.18 Visual inspection of drill-pipe body
7.19 Non-destructive examination
7.20 Marking
7.21 Minimum facility requirements for drill-pipe-body
manufacturer
7.22 Documentation requirements
8 Requirements for tool joints
8.1 Information to be supplied when placing orders for
tool joints
8.2 Dimensional requirements
8.3 Material requirements
8.4 Process of manufacture
8.5 Traceability
8.6 Inspection and testing - General
8.7 Testing of chemical composition
8.8 Tensile tests
8.9 Hardness tests
8.10 Charpy V-notch impact tests
8.11 Imperfections and defects
8.12 Non-destructive examination
8.13 Marking
8.14 Minimum facility requirements for tool-joint
manufacturers
8.15 Documentation requirements for tool joints
Annex A (normative) - Tables in SI units
Annex B (normative) - Figures in SI (USC) units
Annex C (normative) - Tables in USC units
Annex D (normative) - Purchaser inspection
Annex E (informative) - Supplementary requirements
Annex F (informative) - Procedures used to convert from USC
units to SI units for drill-pipe
Annex G (normative) - Product specification levels
Annex H (informative) - API monogram
Bibliography
Defines the technical delivery conditions for steel drill-pipes with upset pipe-body ends and weld-on tool joints for use in drilling and production operations in petroleum and natural gas industries for three product specification levels (PSL-1, PSL-2 and PSL-3).
| DocumentType |
Standard
|
| Pages |
132
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN ISO 11961 : 2010 | Identical |
| EN ISO 11961:2018 | Identical |
| UNI EN ISO 11961 : 2009 | Identical |
| ONORM EN ISO 11961 : 2010 | Identical |
| DIN EN ISO 11961:2009-09 | Identical |
| NEN EN ISO 11961 : 2008 C1 2009 | Identical |
| NBN EN ISO 11961 : 2009 COR 2009 | Identical |
| BS EN ISO 11961:2008 | Identical |
| NS EN ISO 11961 : 2008 AC 2009 | Identical |
| SN EN ISO 11961 : 2009 CORR 2009 | Identical |
| DIN EN ISO 11961:2009-03 | Identical |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| API 5T1 : 2017 | IMPERFECTION AND DEFECT TERMINOLOGY |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| ISO/TS 29001:2010 | Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations |
| ASTM E 309 : 2016 : REDLINE | Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation |
| ISO/TR 9769:1991 | Steel and iron Review of available methods of analysis |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| API 7-2 : 2017 | THREADING AND GAUGING OF ROTARY SHOULDERED CONNECTIONS |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| API 5D : 2001 | SPECIFICATION FOR DRILL PIPE |
| ISO 6892:1998 | Metallic materials Tensile testing at ambient temperature |
| ISO 9303:1989 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of longitudinal imperfections |
| ISO 9304:1989 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Eddy current testing for the detection of imperfections |
| ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM E 10 : 2017-05 | TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ISO 9598:1989 | Seamless steel tubes for pressure purposes Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of transverse imperfections |
| ISO 9402:1989 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of longitudinal imperfections |
| API Q1 : 2013 | SPECIFICATION FOR QUALITY MANAGEMENT SYSTEM REQUIREMENTS FOR MANUFACTURING ORGANIZATIONS FOR THE PETROLEUM AND NATURAL GAS INDUSTRY |
| API 7 : 2001 | SPECIFICATION FOR ROTARY DRILL STEM ELEMENTS |
| ISO 13665:1997 | Seamless and welded steel tubes for pressure purposes Magnetic particle inspection of the tube body for the detection of surface imperfections |
| ISO 11484:2009 | Steel products — Employer's qualification system for non-destructive testing (NDT) personnel |
| API 5C3 : 1994 | BULLETIN ON FORMULAS AND CALCULATIONS FOR CASING, TUBING, DRILL PIPE AND LINE PIPE PROPERTIES |
| ISO/TR 10400:2007 | Petroleum and natural gas industries Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing |
| ISO 10424-2:2007 | Petroleum and natural gas industries — Rotary drilling equipment — Part 2: Threading and gauging of rotary shouldered thread connections |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| ISO 11960:2014 | Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells |
| ASTM E 92 : 2017 : REDLINE | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
| ISO 9305:1989 | Seamless steel tubes for pressure purposes Full peripheral ultrasonic testing for the detection of transverse imperfections |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.