Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation test rooms

Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Language(s)

English, French

Published date

21-09-2010

Publisher

International Organization for Standardization

€185.00

Excluding VAT

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

ISO 3741:2010 specifies methods for determining the sound power level or sound energy level of a noise source from sound pressure levels measured in a reverberation test room. The sound power level (or, in the case of noise bursts or transient noise emission, the sound energy level) produced by the noise source, in frequency bands of width one-third-octave, is calculated using those measurements, including corrections to allow for any differences between the meteorological conditions at the time and place of the test and those corresponding to a reference characteristic impedance. Measurement and calculation procedures are given for both a direct method and a comparison method of determining the sound power level and the sound energy level.

In general, the frequency range of interest includes the one-third-octave bands with mid-band frequencies from 100 Hz to 10 000 Hz. Guidelines for the application of the specified methods over an extended frequency range in respect to lower frequencies are given in an annex. ISO 3741:2010 is not applicable to frequency ranges above the 10 000 Hz one-third-octave band.

The methods specified in ISO 3741:2010 are suitable for all types of noise (steady, non-steady, fluctuating, isolated bursts of sound energy, etc.) defined in ISO 12001.

The noise source under test can be a device, machine, component or sub-assembly. ISO 3741:2010 is applicable to noise sources with a volume not greater than 2 % of the volume of the reverberation test room. For a source with a volume greater than 2 % of the volume of the test room, it is possible that the achievement of results as defined in ISO 12001:1996, accuracy grade 1 (precision grade) is not feasible.

The test rooms that are applicable for measurements made in accordance with ISO 3741:2010 are reverberation test rooms meeting specified requirements.

Information is given on the uncertainty of the sound power levels and sound energy levels determined in accordance with ISO 3741:2010, for measurements made in limited bands of frequency and for A-weighted frequency calculations from them. The uncertainty conforms to ISO 12001:1996, accuracy grade 1 (precision grade).

DevelopmentNote	Supersedes ISO 3742, 495 (04/2001) Supersedes ISO/DIS 3741. (09/2010) Also numbered as ANSI S12.51. (04/2012)
DocumentType	Standard
Pages	61
PublisherName	International Organization for Standardization
Status	Current
Supersedes	ISO 3742:1988 ISO 3741:1999/Cor 1:2001 NS 4817 : 1982 ISO 3741:1999

Standards	Relationship
GOST R ISO 3741 : 2013	Identical
NF EN ISO 3741 : 2012	Identical
NBN EN ISO 3741 : 2010	Identical
NEN EN ISO 3741 : 2010	Identical
NS EN ISO 3741 : 2010	Identical
I.S. EN ISO 3741:2010	Identical
PN EN ISO 3741 : 2011	Identical
SN EN ISO 3741:2011	Identical
AS 5332:2019	Identical
UNE-EN ISO 3741:2011	Identical
BS EN ISO 3741:2009	Identical
EN ISO 3741:2010	Identical
DIN EN ISO 3741:2011-01	Identical
UNI EN ISO 3741 : 2010	Identical
UNE 74031:1993	Similar to
NBN EN 23741 : 1992	Identical
NEN ISO 3741 : 1992	Identical
DIN EN 23741:1991-11	Corresponds
UNE-EN 13510:2000	Identical
UNI EN 23741 : 1992	Identical
NF EN 23741 : 1992	Identical
BS EN ISO 3741:2010	Identical
EN 23741 : 1991	Identical
BS 4196-1:1981	Identical
DIN 45635-2:1987-10	Corresponds
I.S. EN 23741:1992	Identical
BS 4196-1:1991	Identical
NFS 31 022 : LATEST	Identical

ISO 11204:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
CEI EN 60349-4 : 2014	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
BS EN 60349-1:2010	Electric traction. Rotating electrical machines for rail and road vehicles Machines other than electronic converter-fed alternating current motors
UNE-EN 16286-2:2014	Railway applications - Gangway systems between vehicles - Part 2: Acoustic measurements
I.S. EN ISO 3382:2000	ACOUSTICS - MEASUREMENT OF THE REVERBERATION TIME OF ROOMS WITH REFERENCE TO OTHER ACOUSTICAL PARAMETERS
BS EN 16430-1:2014	Fan assisted radiators, convectors and trench convectors Technical specifications and requirements
UNE-EN ISO 17201-3:2010	Acoustics - Noise from shooting ranges - Part 3: Guidelines for sound propagation calculations (ISO 17201-3:2010)
01/202453 DC : DRAFT APRIL 2001	IEC 60034-9 ED.4 - ROTATING ELECTRICAL MACHINERY - PART 9: NOISE LIMITS
ECMA 341 : 4ED 2010	ENVIRONMENTAL DESIGN CONSIDERATIONS FOR ICT & CE PRODUCTS
DD ENV 1397:1996	Heat exchangers. Hydronic room fan coil units. Test procedure for establishing the performance
BS 848-2.6:2000	Fans for general purposes. Methods of noise testing Airborne noise emitted by small air-moving devices
12/30257842 DC : 0	BS ISO 27327-2 - FANS - AIR CURTAIN UNITS - PART 2: LABORATORY METHODS OF TESTING FOR SOUND POWER
UNE-EN ISO 15186-3:2011	Acoustics - Measurement of sound insulation in buildings and of building elements using sound intensity - Part 3: Laboratory measurements at low frequencies (ISO 15186-3:2002)
EN ISO 11202:2010	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
ANSI S12.57 : 2011	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
SMPTE EG 16 : 2014	MEASUREMENT METHODS FOR FILM AND DIGITAL MOTION-PICTURE CAMERA ACOUSTICAL NOISE - FIELD METHOD
BS 4196-4:1981	Sound power levels of noise sources Engineering methods for determination of sound power levels for sources in free-field conditions over a reflecting plane
BS ISO 10494:1993	Gas turbines and gas turbine sets. Measurement of emitted airborne noise. Engineering/survey method
BS 848-2.2(2004) : 2004	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 2: REVERBERANT ROOM METHOD
IPC 9591 : 0	PERFORMANCE PARAMETERS (MECHANICAL, ELECTRICAL, ENVIRONMENTAL AND QUALITY/RELIABILITY) FOR AIR MOVING DEVICES
ASTM E 1704 : 1995 : R2018	Standard Guide for Specifying Acoustical Performance of Sound-Isolating Enclosures
PREN ISO 11200 : DRAFT 2012	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO/DIS 11200:2012)
UNE-EN ISO 3382-1:2010	Acoustics - Measurement of room acoustic parameters - Part 1: Performance spaces (ISO 3382-1:2009)
BS 848-2.1(2004) : 2004	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 1: GENERAL OVERVIEW
BS EN 16583:2015	Heat exchangers. Hydronic room fan coils units. Determination of the sound power level
UNI EN 15657-1 : 2009	ACOUSTIC PROPERTIES OF BUILDING ELEMENTS AND OF BUILDINGS - LABORATORY MEASUREMENT OF AIRBORNE AND STRUCTURE BORNE SOUND FROM BUILDING EQUIPMENT - PART 1: SIMPLIFIED CASES WHERE THE EQUIPMENT MOBILITIES ARE MUCH HIGHER THAN THE RECEIVER MOBILITIES, TAKING WHIRLPOOL BATHS AS AN EXAMPLE
CSA Z10535 : 2003	HOISTS FOR THE TRANSFER OF DISABLED PERSONS - REQUIREMENTS AND TEST METHODS
ANSI/PIMA IT7.406:1997	AUDIOVISUAL SYSTEMS - SOUND SYSTEM EQUIPMENT - PART 7: HEADPHONES AND EARPHONES
PREN 50134-3 : DRAFT 2009	ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 3: LOCAL UNIT AND CONTROLLER
ISO 17201-3:2010	Acoustics Noise from shooting ranges Part 3: Guidelines for sound propagation calculations
EEMUA 140 : 2014	NOISE PROCEDURE SPECIFICATION
I.S. EN 12102:2013	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
S.R. CEN ISO/TR 22100-1:2017	SAFETY OF MACHINERY - RELATIONSHIP WITH ISO 12100 - PART 1: HOW ISO 12100 RELATES TO TYPE-B AND TYPE-C STANDARDS (ISO/TR 22100-1:2015)
I.S. EN 15657-1:2009	ACOUSTIC PROPERTIES OF BUILDING ELEMENTS AND OF BUILDINGS - LABORATORY MEASUREMENT OF AIRBORNE AND STRUCTURE BORNE SOUND FROM BUILDING EQUIPMENT - PART 1: SIMPLIFIED CASES WHERE THE EQUIPMENT MOBILITIES ARE MUCH HIGHER THAN THE RECEIVER MOBILITIES, TAKING WIRLPOOL BATHS AS AN EXAMPLE
I.S. EN 60034-9:2005	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
UNE-EN 13141-11:2015	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units
ANSI S12.23 : 1989 : R2006	METHOD FOR THE DESIGNATION OF SOUND POWER EMITTED BY MACHINERY AND EQUIPMENT
I.S. EN ISO 3382-1:2009	ACOUSTICS - MEASUREMENT OF ROOM ACOUSTIC PARAMETERS - PART 1: PERFORMANCE SPACES
ANSI S12.23:1989(R2011)	METHOD FOR THE DESIGNATION OF SOUND POWER EMITTED BY MACHINERY AND EQUIPMENT
BS EN ISO 17201-1:2005	Acoustics. Noise from shooting ranges Determination of muzzle blast by measurement
ANSI/ASA S12.56/ISO 3746 : 2011(R2016)	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - SURVEY METHOD USING AN ENVELOPING MEASUREMENT SURFACE OVER A REFLECTING PLANE
ANSI/ASA S12.23 : 1989(R2016)	METHOD FOR THE DESIGNATION OF SOUND POWER EMITTED BY MACHINERY AND EQUIPMENT
ANSI/ASA S12.53 PART 2 : 1999(R2015)	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
UNI EN 12102 : 2014	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
UNI EN 13141-7 : 2011	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 7: PERFORMANCE TESTING OF A MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR SINGLE FAMILY DWELLINGS
I.S. EN ISO 3743-2:2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TESTS ROOMS
DIN EN 15036-1:2006-12	Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1: Airborne noise emissions from heat generators
DIN EN 13141-6:2015-02	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING
DIN EN 12012-3:2010-02	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 3: SAFETY REQUIREMENTS FOR SHREDDERS
DIN EN ISO 11200:2014-10	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO 11200:2014)
BS EN ISO 5135:1999	Acoustics. Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room
IEC 61947-2:2001	Electronic projection - Measurement and documentation of key performance criteria - Part 2: Variable resolution projectors
UNE-EN ISO 11200:2014	Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:2014)
BS EN ISO 15186-1:2003	Acoustics. Measurement of sound insulation in buildings and of building elements using sound intensity Laboratory measurements
BS EN 13141-2:2010	Ventilation for buildings. Performance testing of components/products for residential ventilation Exhaust and supply air terminal devices
BS EN ISO 11691:1997	Acoustics. Measurement of insertion loss of ducted silencers without flow. Laboratory survey method
ISO 3746:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
UNE-EN ISO 9614-1:2010	Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993)
BS EN ISO 3382:2000	Acoustics. Measurement of the reverberation time of rooms with reference to other acoustical parameters
ISO 11203:1995	Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
BS EN ISO 11957:2009	Acoustics. Determination of sound insulation performance of cabins. Laboratory and in situ measurements
BS EN ISO 11201:2010	Acoustics. Noise emitted by machinery and equipment. Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
BS EN ISO 11690-2:1997	Acoustics. Recommended practice for the design of low-noise workplaces containing machinery Noise control measures
I.S. EN ISO 11691:2009	ACOUSTICS - MEASUREMENT OF INSERTION LOSS OF DUCTED SILENCERS WITHOUT FLOW - LABORATORY SURVEY METHOD
I.S. EN 13141-6:2014	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING
I.S. EN ISO 4871:2009	ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT
DIN EN ISO 11957:2010-01	Acoustics - Determination of sound insulation performance of cabins - Laboratory and in situ measurements (ISO 11957:1996)
NF EN ISO 11691 : 2009	ACOUSTICS - MEASUREMENT OF INSERTION LOSS OF DUCTED SILENCERS WITHOUT FLOW - LABORATORY SURVEY METHOD
EN 13141-11:2015	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units
EN 13141-8:2014	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room
EN 60704-1:2010/A11:2012	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE NOISE - PART 1: GENERAL REQUIREMENTS (IEC 60704-1:2010)
DIN EN ISO 11691:2010-01	Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995); German version EN ISO 11691:2009
EN 12102:2013	Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling - Measurement of airborne noise - Determination of the sound power level
EN 13141-2:2010	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 2: Exhaust and supply air terminal devices
EN 60034-9:2005/A1:2007	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
EN 61947-1:2002	Electronic projection - Measurement and documentation of key performance criteria - Part 1: Fixed resolution projectors
DIN EN ISO 4871:2009-11	Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 61096:1993/A1:1996	METHODS OF MEASURING THE CHARACTERISTICS OF REPRODUCING EQUIPMENT FOR DIGITAL AUDIO COMPACT DISCS
EN 62121:2001	Methods of measurement for minidisc recorders/players
EN 12012-3:2001+A1:2008	Plastics and rubber machines - Size reduction machines - Part 3: Safety requirements for shredders
EN 12012-2:2001+A2:2008	Plastics and rubber machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers
NBR IEC 60034-9 : 2011	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
ONORM EN 13141-8 : 2014	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 8: PERFORMANCE TESTING OF UN-DUCTED MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR A SINGLE ROOM
BS EN ISO 7235:2009	Acoustics. Laboratory measurement procedures for ducted silencers and air-terminal units. Insertion loss, flow noise and total pressure loss
ONORM EN 12354-5 : 2011	BUILDING ACOUSTICS - ESTIMATION OF ACOUSTIC PERFORMANCE OF BUILDING FROM THE PERFORMANCE OF ELEMENTS - PART 5: SOUNDS LEVELS DUE TO THE SERVICE EQUIPMENT
I.S. EN 12354-5:2009	BUILDING ACOUSTICS - ESTIMATION OF ACOUSTIC PERFORMANCE OF BUILDING FROM THE PERFORMANCE OF ELEMENTS - PART 5: SOUNDS LEVELS DUE TO THE SERVICE EQUIPMENT
IPC 9592 : B	REQUIREMENTS FOR POWER CONVERSION DEVICES FOR THE COMPUTER AND TELECOMMUNICATIONS INDUSTRIES
ONORM EN 16583 : 2015	HEAT EXCHANGERS - HYDRONIC ROOM FAN COILS UNITS - DETERMINATION OF THE SOUND POWER LEVEL
UNI EN ISO 15186-3 : 2010	ACOUSTICS - MEASUREMENT OF SOUND INSULATION IN BUILDINGS AND OF BUILDING ELEMENTS USING SOUND INTENSITY - PART 3: LABORATORY MEASUREMENTS AT LOW FREQUENCIES
DIN EN 12012-1:2015-05 (Draft)	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS
ISO 3740:2000	Acoustics Determination of sound power levels of noise sources Guidelines for the use of basic standards
13/30279964 DC : 0	BS EN ISO 3743-2:1994/AMD 1 - ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
08/30178754 DC : DRAFT MAR 2008	BS EN 60268-7 - SOUND SYSTEM EQUIPMENT - PART 7 - HEADPHONES AND EARPHONES (GMT)
07/30081117 DC : 0	BS EN ISO 3382-1 - ACOUSTICS - MEASUREMENT OF ROOM ACOUSTIC PARAMETERS - PART 1: PERFORMANCE ROOMS
BS ISO 9611:1996	Acoustics. Characterization of sources of structure-borne sound with respect to sound radiation from connected structures. Measurement of velocity at the contact points of machinery when resiliently mounted
I.S. EN 50134-5:2004	ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 5: INTERCONNECTIONS AND COMMUNICATIONS
04/30122794 DC : DRAFT SEP 2004	EN 15036-1 - HEATING BOILERS - TEST REGULATIONS FOR AIRBORNE NOISE EMISSIONS FROM HEAT GENERATORS - PART 1: AIRBORNE NOISE EMISSIONS FROM HEAT GENERATORS AT PLACE OF INSTALLATION
BS EN 62075:2012	Audio/video, information and communication technology equipment. Environmentally conscious design
DD ISO/TS 7849-1:2009	Acoustics. Determination of airborne sound power levels emitted by machinery using vibration measurement Survey method using a fixed radiation factor
BS EN 60349-4:2013	Electric traction. Rotating electrical machines for rail and road vehicles Permanent magnet synchronous electrical machines connected to an electronic converter
13/30267124 DC : 0	BS EN 13141-11 - VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 11: POSITIVE PRESSURE VENTILATION SYSTEMS
DIN EN ISO 11201:2010-10	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
BS EN ISO 15186-3:2010	Acoustics. Measurement of sound insulation in buildings and of building elements using sound intensity Laboratory measurements at low frequencies
BS ISO 9296:2017	Acoustics. Declared noise emission values of information technology and telecommunications equipment
BS ISO 27327-2:2014	Fans. Air curtain units Laboratory methods of testing for sound power
00/714693 DC : DRAFT OCT 2000	PREN 13141-7 - VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 7: PERFORMANCE TESTING A MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR SINGLE FAMILY DWELLINGS
I.S. EN ISO 3740:2000	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
CSA Z107.58 : 2015	NOISE EMISSION DECLARATIONS FOR MACHINERY
12/30271386 DC : 0	BS EN 12102 - AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
UNI EN ISO 10821 : 2010	INDUSTRIAL SEWING MACHINES - SAFETY REQUIREMENTS FOR SEWING MACHINES, UNITS AND SYSTEMS
PREN 13141-5 : DRAFT 2017	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 5: COWLS AND ROOF OUTLET TERMINAL DEVICES
DIN EN 16583:2015-10	Heat exchangers - Hydronic room fan coils units - Determination of the sound power level
UNI ISO 13347-1 : 2009	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 1: GENERAL OVERVIEW
BS ISO 15665:2003	Acoustics. Acoustic insulation for pipes, valves and flanges
07/30094858 DC : 0	BS ISO 3747 - ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
BS EN ISO 3382-1:2009	Acoustics. Measurement of room acoustic parameters Performance spaces
I.S. EN 16286-2:2013	RAILWAY APPLICATIONS - GANGWAY SYSTEMS BETWEEN VEHICLES - PART 2: ACOUSTIC MEASUREMENTS
PREN 13053 : DRAFT 2017	VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
17/30359986 DC : 0	BS EN ISO 7779 - ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
BS EN ISO 17201-3:2010	Acoustics. Noise from shooting ranges Guidelines for sound propagation calculations
ANSI S12.10:2002(R2007)	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
CSA Z10535 : 2003 : R2014	HOISTS FOR THE TRANSFER OF DISABLED PERSONS - REQUIREMENTS AND TEST METHODS
BS 7140:1995	Airborne noise emitted by woodworking machine tools. Operating conditions for woodworking machines
CEI EN 50134-5 : 2006	ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 5: INTERCONNECTIONS AND COMMUNICATIONS
NF EN 60034-9 : 2005 AMD 1 2007	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
CSA 6.19-17	Residential carbon monoxide alarming devices
ANSI/ASA S12.54/ISO 3744 : 2011(R2016)	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
BS ISO 13347-1 : 2004	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 1: GENERAL OVERVIEW
BS EN 60268-5 : 2003	SOUND SYSTEM EQUIPMENT - PART 5: LOUDSPEAKERS
PREN 12102-2 : DRAFT 2016	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS - DETERMINATION OF THE SOUND POWER LEVEL - PART 2: HEAT PUMP WATER HEATERS
CEI EN 60349-1 : 2012	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
PREN 13141-6 : DRAFT 2012	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING
I.S. EN 60268-5:2003	SOUND SYSTEM EQUIPMENT - PART 5: LOUDSPEAKERS
ECMA 370 : 5ED 2015	TED - THE ECO DECLARATION
I.S. EN 16583:2015	HEAT EXCHANGERS - HYDRONIC ROOM FAN COILS UNITS - DETERMINATION OF THE SOUND POWER LEVEL
EN ISO 7779:2010	Acoustics - Measurement of airborne noise emitted by information technology and telecommunications equipment (ISO 7779:2010)
UNI EN ISO 7779 : 2010	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
BS EN 60704-2-3:2002	Household and similar electrical appliances. Test code for the determination of airborne acoustical noise Particular requirements for dishwashers
ASTM E 492 : 2009 : R2016 : EDT 1	Standard Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using the Tapping Machine
ASTM E 90 : 2009 : R2016	Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
UNI EN 12012-1 : 2008	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS
EN ISO 3740:2000	Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards (ISO 3740:2000)
ASTM E 3133 : 2018	Standard Test Method for Laboratory Measurement of Floor Impact Sound Radiation Using the Tapping Machine
ASTM F 2544 : 2011 : R2018	Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units
BS EN ISO 3740:2001	Acoustics. Determination of sound power levels of noise sources. Guidelines for the use of basic standards
ASTM E 492 : 2009	Standard Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using the Tapping Machine
I.S. EN 50134-3:2012	ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 3: LOCAL UNIT AND CONTROLLER
NF EN ISO 3743-2 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
EN ISO 3746:2010	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
I.S. EN 13053:2006	VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
ISO/TR 18569:2004	Safety of machinery Guidelines for the understanding and use of safety of machinery standards
DIN EN 12354-5:2009-10	Building acoustics - Estimation of acoustic performance of building from the performance of elements - Part 5: Sounds levels due to the service equipment
DIN EN 13141-8:2014-09	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room
ISO 4871:1996	Acoustics — Declaration and verification of noise emission values of machinery and equipment
IEC 60349-2:2010	Electric traction - Rotating electrical machines for rail and road vehicles - Part 2: Electronic converter-fed alternating current motors
ISO 5136:2003	Acoustics — Determination of sound power radiated into a duct by fans and other air-moving devices — In-duct method
BS EN ISO 11546-1:1996	Acoustics. Determination of sound insulation performances of enclosures Measurements under laboratory conditions (for declaration purposes)
ISO 11689:1996	Acoustics — Procedure for the comparison of noise-emission data for machinery and equipment
BS EN ISO 3744:2010	Acoustics. Determination of sound power levels and sound energy levels of noise sources using sound pressure. Engineering methods for an essentially free field over a reflecting plane
I.S. EN ISO 11957:2009	ACOUSTICS - DETERMINATION OF SOUND INSULATION PERFORMANCE OF CABINS - LABORATORY AND IN SITU MEASUREMENTS
DIN EN 12012-2:2010-02	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
I.S. EN ISO 12001:2009	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - RULES FOR THE DRAFTING AND PRESENTATION OF A NOISE TEST CODE
I.S. EN ISO 3747:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
I.S. EN ISO 5136:2009	ACOUSTICS - DETERMINATION OF SOUND POWER RADIATED INTO A DUCT BY FANS AND OTHER AIR-MOVING DEVICES - IN-DUCT METHOD
I.S. EN ISO 7235:2009	ACOUSTICS - LABORATORY MEASUREMENT PROCEDURES FOR DUCTED SILENCERS AND AIR-TERMINAL UNITS - INSERTION LOSS, FLOW NOISE AND TOTAL PRESSURE LOSS
I.S. EN ISO 3743-1:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL MOVABLE SOURCES IN REVERBERANT FIELDS - PART 1: COMPARISON METHOD FOR A HARD-WALLED TEST ROOM
I.S. EN ISO 6926:2016	ACOUSTICS - REQUIREMENTS FOR THE PERFORMANCE AND CALIBRATION OF REFERENCE SOUND SOURCES USED FOR THE DETERMINATION OF SOUND POWER LEVELS (ISO 6926:2016)
UNI EN ISO 11691 : 2009	ACOUSTICS - MEASUREMENT OF INSERTION LOSS OF DUCTED SILENCERS WITHOUT FLOW - LABORATORY SURVEY METHOD
I.S. EN ISO 3745:2012	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS (ISO 3745:2012)
I.S. EN ISO 11204:2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS
DIN EN ISO 11200:1996-07	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO 11200:2014)
I.S. EN 13141-8:2014	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 8: PERFORMANCE TESTING OF UN-DUCTED MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR A SINGLE ROOM
I.S. EN 13141-7:2010	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 7: PERFORMANCE TESTING OF A MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR SINGLE FAMILY DWELLINGS
DIN EN 13053:2012-02	VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS (INCLUDES AMENDMENT A1:2011)
DIN EN 13141-2:2010-12	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 2: Exhaust and supply air terminal devices
DIN EN 13141-7:2011-01	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings
DIN EN ISO 7779:2011-01	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
EN ISO 11690-1:1996	Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 1: Noise control strategies (ISO 11690-1:1996)
I.S. EN ISO 9614-1:2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 1: MEASUREMENT AT DISCRETE POINTS
I.S. EN ISO 1680:2013	ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES (ISO 1680:2013)
EN ISO 6926:2016	Acoustics - Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels (ISO 6926:2016)
I.S. EN ISO 11546-1:2009	ACOUSTICS - DETERMINATION OF SOUND INSULATION PERFORMANCES OF ENCLOSURES - PART 1: MEASUREMENTS UNDER LABORATORY CONDITIONS (FOR DECLARATION PURPOSES)
I.S. EN ISO 3744:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
I.S. EN 13141-2:2010	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 2: EXHAUST AND SUPPLY AIR TERMINAL DEVICES
I.S. EN 12012-3:2001	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 3: SAFETY REQUIREMENTS FOR SHREDDERS
I.S. EN 12012-2:2001	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
DIN EN ISO 10821:2013-02	INDUSTRIAL SEWING MACHINES - SAFETY REQUIREMENTS FOR SEWING MACHINES, UNITS AND SYSTEMS (ISO 10821:2005 + AMD 1:2009)
I.S. EN ISO 9614-3:2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 3: PRECISION METHOD FOR MEASUREMENT BY SCANNING
EN ISO 11691:2009	Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995)
DIN EN 12012-2:2004-03	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
I.S. EN ISO 11202:2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
I.S. EN ISO 11201:2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS IN AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE WITH NEGLIGIBLE ENVIRONMENTAL CORRECTIONS
I.S. EN ISO 3746:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - SURVEY METHOD USING AN ENVELOPING MEASUREMENT SURFACE OVER A REFLECTING PLANE
DIN EN 15657-1:2009-10	ACOUSTIC PROPERTIES OF BUILDING ELEMENTS AND OF BUILDINGS - LABORATORY MEASUREMENT OF AIRBORNE AND STRUCTURE BORNE SOUND FROM BUILDING EQUIPMENT - PART 1: SIMPLIFIED CASES WHERE THE EQUIPMENT MOBILITIES ARE MUCH HIGHER THAN THE RECEIVER MOBILITIES, TAKING WIRLPOOL BATHS AS AN EXAMPLE
DIN EN ISO 7235:2010-01	Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss (ISO 7235:2003)
UNI EN ISO 11689 : 1998	ACOUSTICS - PROCEDURE FOR THE COMPARISON OF NOISE-EMISSION DATA FOR MACHINERY AND EQUIPMENT
BS 4196-2:1991	Sound power levels of noise sources Precision methods for determination of sound power levels for discrete-frequency and narrow-band sources in reverberation rooms
VDI 2715:2011-11	Noise control in heating systems
BS 4773-2:1989	Methods for testing and rating air terminal devices for air distribution systems Acoustic testing
DIN EN 16286-2:2013-09	Railway applications - Gangway systems between vehicles - Part 2: Acoustic measurements
10/30094845 DC : 0	BS ISO 3745 - ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC TEST ROOMS AND HEMI-ANECHOIC TEST ROOMS
EN 13141-7:2010	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings
UNI EN ISO 3382-3 : 2012	ACOUSTICS - MEASUREMENT OF ROOM ACOUSTIC PARAMETERS - PART 3: OPEN PLAN OFFICES
BS EN 15657-1:2009	Acoustic properties of building elements and of buildings. Laboratory measurement of airborne and structure borne sound from building equipment Simplified cases where the equipment mobilities are much higher than the receiver mobilities, taking whirlpool baths as an example
BS ISO 15664:2001	Acoustics. Noise control design procedures for open plant
BS EN 50134-5:2004	Alarm systems. Social alarm systems Interconnections and communications
09/30182105 DC : 0	BS EN 60349-2 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
BS EN 60349-2:2010	Electrical traction. Rotating electrical machines for rail and road vehicles Electronic converter-fed alternating current motors
ECMA 74 : 14ED 2017	MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
BS ISO 6926 : 99 AMD 13404	ACOUSTICS - REQUIREMENTS FOR THE PERFORMANCE AND CALIBRATION OF REFERENCE SOUND SOURCES FOR THE DETERMINATION OF SOUND POWER LEVELS
BS ISO 10302-1:2011	Acoustics. Measurement of airborne noise emitted and structure-borne vibration induced by small air-moving devices Airborne noise measurement
09/30202602 DC : 0	BS EN 50134-3 - ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 3: LOCAL UNIT AND CONTROLLER
I.S. EN 60349-1:2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTOR-FED ALTERNATING CURRENT MOTORS
BS 4196-6:1981	Sound power levels of noise sources Survey method for determination of sound power levels of noise sources
ANSI S12.53/2 : 1999	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
11/30246444 DC : 0	BS EN 62075 ED 2.0 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN
I.S. EN ISO 9295:2015	ACOUSTICS - DETERMINATION OF HIGH-FREQUENCY SOUND POWER LEVELS EMITTED BY MACHINERY AND EQUIPMENT (ISO 9295:2015)
ECMA 109 : 7ED 2016	DECLARED NOISE EMISSION VALUES OF INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
16/30345760 DC : 0	BS EN 12102-2 - AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS - DETERMINATION OF THE SOUND POWER LEVEL - PART 2: HEAT PUMP WATER HEATERS
BS EN 60268-7:2011	Sound system equipment Headphones and earphones
DIN EN 16430-1:2015-03	FAN ASSISTED RADIATORS, CONVECTORS AND TRENCH CONVECTORS - PART 1: TECHNICAL SPECIFICATIONS AND REQUIREMENTS
03/316891 DC : DRAFT OCT 2003	EN 13053 - VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATINGS AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
BS 4196-5:1981	Sound power levels of noise sources Precision methods for determination of sound power levels for sources in anechoic and semi-anechoic rooms
BS 7458-1:1991	Test code for the measurement of airborne noise emitted by rotating electrical machinery Engineering method for free-field conditions over a reflecting plane
BS ISO 13347-2:2004	Industrial fans. Determination of fan sound power levels under standardized laboratory conditions Reverberant room method
UNE-EN ISO 7779:2011	Acoustics - Measurement of airborne noise emitted by information technology and telecommunications equipment (ISO 7779:2010)
UNE-EN 16430-1:2015	Fan assisted radiators, convectors and trench convectors - Part 1: Technical specifications and requirements
BS EN 60704-1 : 2010	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE NOISE - PART 1: GENERAL REQUIREMENTS
I.S. EN 60349-4:2013	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER (IEC 60349-4:2012 (EQV))
SAE J 2883 : 2015	LABORATORY MEASUREMENT OF RANDOM INCIDENCE SOUND ABSORPTION TESTS USING A SMALL REVERBERATION ROOM
CEI EN 60349-2 : 2012	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
EN 50134-5:2004	Alarm systems - Social alarm systems - Part 5: Interconnections and communications
I.S. EN 27574-1:1991	ACOUSTICS - STATISTICAL METHODS FOR DETERMINING AND VERIFYING STATED NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT - GENERAL CONSIDERATIONS AND DEFINITIONS
I.S. EN 61947-1:2002	ELECTRONIC PROJECTION - MEASUREMENT AND DOCUMENTATION OF KEY PERFORMANCE CRITERIA - PART 1: FIXED RESOLUTION PROJECTORS
ISO 3742:1988	Acoustics — Determination of sound power levels of noise sources — Precision methods for discrete-frequency and narrow-band sources in reverberation rooms
ISO 3743-2:2018	Acoustics — Determination of sound power levels of noise sources using sound pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods for special reverberation test rooms
ISO 10843:1997	Acoustics — Methods for the description and physical measurement of single impulses or series of impulses
ANSI S12.11-1 : 2013	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED AND STRUCTURE-BORNE VIBRATION INDUCED BY SMALL AIR-MOVING DEVICES - PART 1: AIRBORNE NOISE MEASUREMENT
UNI EN 16286-2 : 2013	RAILWAY APPLICATIONS - GANGWAY SYSTEMS BETWEEN VEHICLES - PART 2: ACOUSTIC MEASUREMENTS
ECMA 275-1 : 4ED 2017	MEASUREMENT OF AIRBORNE NOISE EMITTED AND STRUCTURE-BORNE VIBRATION INDUCED BY SMALL AIR-MOVING DEVICES - PART 1: AIRBORNE NOISE MEASUREMENT
BS EN ISO 7779:2010	Acoustics. Measurement of airborne noise emitted by information technology and telecommunications equipment
ASTM E 90 : 2009	Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
UNE-EN 16583:2016	Heat exchangers - Hydronic room fan coils units - Determination of the sound power level
PREN 12102 : DRAFT 2012	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
ASTM E 1704 : 1995 : R2002	Standard Guide for Specifying Acoustical Performance of Sound-Isolating Enclosures
ISO 9296:2017	Acoustics — Declared noise emission values of information technology and telecommunications equipment
ANSI/ASA S12.58:2012	SOUND POWER LEVEL DETERMINATION FOR SOURCES USING A SINGLE-SOURCE POSITION
NF EN ISO 7779 : 2010	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
ISO 17201-1:2005	Acoustics Noise from shooting ranges Part 1: Determination of muzzle blast by measurement
ISO 7779:2010	Acoustics Measurement of airborne noise emitted by information technology and telecommunications equipment
ISO 4872:1978	Acoustics Measurement of airborne noise emitted by construction equipment intended for outdoor use Method for determining compliance with noise limits
IEC 62851-5:2014	Alarm and electronic security systems - Social alarm systems - Part 5: Interconnections and communications
DIN EN ISO 6926:2016-08	Acoustics - Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels (ISO 6926:2016)
DIN EN ISO 1680:2014-04	ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES (ISO 1680:2013)
DIN EN ISO 3747:2011-03	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010)
UNI EN ISO 11202 : 2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORKSTATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
ISO 11546-1:1995	Acoustics Determination of sound insulation performances of enclosures Part 1: Measurements under laboratory conditions (for declaration purposes)
UNE-EN 60349-2:2011	Electric traction - Rotating electrical machines for rail and road vehicles -- Part 2: Electronic converter-fed alternating current motors
ISO 6926:2016	Acoustics Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels
BS EN 28960:1993	Refrigerators, frozen food storage cabinets and food freezers for household and similar use. Measurement of emission of airborne acoustical noise
UNE-EN ISO 11203:2010	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)
ISO 7574-1:1985	Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 1: General considerations and definitions
ISO 3745:2012	Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms
BS EN ISO 14257:2001	Acoustics. Measurement and parametric description of spatial sound distribution curves in workrooms for evaluation of their acoustical performance
UNE-EN ISO 5136:2010	Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method (ISO 5136:2003)
UNE-EN 13141-2:2011	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 2: Exhaust and supply air terminal devices
ISO 3747:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering/survey methods for use in situ in a reverberant environment
BS EN 13053 : 2006	VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
IEC 61183:1994	Electroacoustics - Random-incidence and diffuse-field calibration of sound level meters
UNE-EN ISO 6926:2016	Acoustics - Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels (ISO 6926:2016)
I.S. EN ISO 5135:1999	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE FROM AIR-TERMINAL DEVICES, AIR-TERMINAL UNITS, DAMPERS AND VALVES BY MEASUREMENT IN A REVERBERATION ROOM
ANSI/ASA S12.23:1989(R2020)	METHOD FOR THE DESIGNATION OF SOUND POWER EMITTED BY MACHINERY AND EQUIPMENT
EN 60268-7:2011	Sound system equipment - Part 7: Headphones and earphones
ASA/ANSI S12.10 PART 2:2011(R2020)	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT - PART 2: DECLARATION OF NOISE EMISSION LEVELS
EN 13487 : 2003	HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS AND DRY COOLERS - SOUND MEASUREMENT
EN ISO 11203:2009	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)
ANSI/ASA S12.10 PART 1:2010(R2020)	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT - PART 1: DETERMINATION OF SOUND POWER LEVEL AND EMISSION SOUND PRESSURE LEVEL
UNI EN ISO 11203 : 2009	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS FROM THE SOUND POWER LEVEL
EN ISO 5135:1998	Acoustics - Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room (ISO 5135:1997)
ONORM EN ISO 11200 : 2014	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO 11200:2014)
I.S. EN ISO 11203:2009	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS FROM THE SOUND POWER LEVEL
EN ISO 15186-1:2003	Acoustics - Measurement of sound insulation in buildings and of building elements using sound intensity - Part 1: Laboratory measurements (ISO 15186-1:2000)
UNI EN ISO 3743-2 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
UNI EN ISO 3744 : 2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
UNI EN ISO 11204 : 2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORKSTATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS
UNI EN ISO 9614-3 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 3: PRECISION METHOD FOR MEASUREMENT BY SCANNING
UNI EN ISO 12001 : 2009	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - RULES FOR THE DRAFTING AND PRESENTATION OF A NOISE TEST CODE
UNI EN ISO 11957 : 2009	ACOUSTICS - DETERMINATION OF SOUND INSULATION PERFORMANCE OF CABINS - LABORATORY AND IN SITU MEASUREMENTS
UNI EN ISO 4871 : 2009	ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT
UNI EN ISO 11201 : 2010	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
UNI EN 12012-3 : 2008	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 3: SAFETY REQUIREMENTS FOR SHREDDERS
UNI EN ISO 9614-1 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 1: MEASUREMENT AT DISCRETE POINTS
UNI EN 13141-2 : 2010	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 2: EXHAUST AND SUPPLY AIR TERMINAL DEVICES
UNI EN ISO 7235 : 2009	ACOUSTICS - LABORATORY MEASUREMENT PROCEDURES FOR DUCTED SILENCERS AND AIR- TERMINAL UNITS - INSERTION LOSS, FLOW NOISE AND TOTAL PRESSURE LOSS
UNI EN ISO 3746 : 2011	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - SURVEY METHOD USING AN ENVELOPING MEASUREMENT SURFACE OVER A REFLECTING PLANE
UNI EN ISO 5136 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER RADIATED INTO A DUCT BY FANS AND OTHER AIR-MOVING DEVICES - IN-DUCT METHOD
UNI EN ISO 3747 : 2011	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
UNI EN ISO 3743-1 : 2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL MOVABLE SOURCES IN REVERBERANT FIELDS - PART 1: COMPARISON METHOD FOR A HARD-WALLED TEST ROOM
UNI EN 12012-2 : 2008	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
UNI EN ISO 11546-1 : 2009	ACOUSTICS - DETERMINATION OF SOUND INSULATION PERFORMANCES OF ENCLOSURES - PART 1: MEASUREMENTS UNDER LABORATORY CONDITIONS (FOR DECLARATION PURPOSES)
UNI EN 12354-5 : 2009	BUILDING ACOUSTICS - ESTIMATION OF ACOUSTIC PERFORMANCE OF BUILDING FROM THE PERFORMANCE OF ELEMENTS - PART 5: SOUNDS LEVELS DUE TO THE SERVICE EQUIPMENT
UNI EN 13141-8 : 2014	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 8: PERFORMANCE TESTING OF UN-DUCTED MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR A SINGLE ROOM
UNI EN ISO 1680 : 2014	ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES
UNE-EN 60349-4:2013	Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
UNI EN ISO 3382-1 : 2009	ACOUSTICS - MEASUREMENT OF ROOM ACOUSTIC PARAMETERS - PART 1: PERFORMANCE SPACES
14/30275192 DC : 0	BS EN ISO 6926 - ACOUSTICS - REQUIREMENTS FOR THE PERFORMANCE AND CALIBRATION OF REFERENCE SOUND SOURCES USED FOR THE DETERMINATION OF SOUND POWER LEVELS
DIN EN ISO 3382-3:2012-05	Acoustics - Measurement of room acoustic parameters - Part 3: Open plan offices (ISO 3382-3:2012)
DIN EN 23742:1991-11	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - PRECISION METHODS FOR DISCRETE-FREQUENCY AND NARROW-BAND SOURCES IN REVERBERATION ROOMS
DIN EN ISO 11202:2010-10	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
PREN 13487 : DRAFT 2017	HEAT EXCHANGER - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS AND DRY COOLERS - SOUND MEASUREMENT
99/561983 DC : APR 99	ISO/DIS 14257 - ACOUSTICS - MEASUREMENT AND MODELLING OF SPATIAL SOUND DISTRIBUTION CURVES IN WORKROOMS FOR EVALUATION OF THEIR ACOUSTICAL PERFORMANCE
BS EN 13141-11:2015	Ventilation for buildings. Performance testing of components/products for residential ventilation Supply ventilation units
14/30291684 DC : 0	BS ISO 9296 - ACOUSTICS - DECLARED NOISE EMISSION VALUES OF INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS
DIN EN ISO 3382-1:2009-10	ACOUSTICS - MEASUREMENT OF ROOM ACOUSTIC PARAMETERS - PART 1: PERFORMANCE SPACES
17/30309708 DC : 0	BS EN ISO 3740 - ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
DIN EN ISO 3744:2011-02	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
BS EN ISO 3382-3:2012	Acoustics. Measurement of room acoustic parameters Open plan offices
12/30255711 DC : 0	BS EN 16430-1 - FAN ASSISTED RADIATORS, CONVECTORS AND TRENCH CONVECTORS - PART 1: TECHNICAL SPECIFICATIONS AND REQUIREMENTS
CEI EN 61947-2 : 2002	ELECTRONIC PROJECTION - MEASUREMENT AND DOCUMENTATION OF KEY PERFORMANCE CRITERIA - PART 2: VARIABLE RESOLUTION PROJECTORS (IEC 61947-2:2001)
BS EN 12012-1 : 2007	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS
17/30356046 DC : DRAFT AUG 2017	BS EN ISO 17201-1 - ACOUSTICS - NOISE FROM SHOOTING RANGES - PART 1: DETERMINATION OF MUZZLE BLAST BY MEASUREMENT
13/30267113 DC : 0	BS EN 13141-6 - VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING
BS EN 61183:1995	Electroacoustics. Random-incidence and diffuse-field calibration of sound level meters
07/30098123 DC : 0	BS ISO 10302-1 - ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED AND STRUCTURE-BORNE VIBRATION INDUCED BY SMALL AIR-MOVING DEVICES - PART 1: AIRBORNE NOISE MEASUREMENT
17/30354748 DC : 0	BS ISO 20189-1 - ACOUSTICS - SCREENS FURNITURE AND SINGLE OBJECTS INTENDED FOR INTERIOR USE - RATING OF SOUND ABSORPTION AND SOUND REDUCTION OF ELEMENTS BASED ON LABORATORY MEASUREMENTS
BS ISO 3743-2 : 1994 AMD 9426	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - METHODS FOR SPECIAL REVERBERATION TEST ROOMS
I.S. EN ISO 7779:2010	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
SAE J192_201301	MAXIMUM EXTERIOR SOUND LEVEL FOR SNOWMOBILES
CEI EN 61947-1 : 2003	ELECTRONIC PROJECTION - MEASUREMENT AND DOCUMENTATION OF KEY PERFORMANCE CRITERIA - PART 1: FIXED RESOLUTION PROJECTORS (IEC 61947-1:2002)
CEI EN 60268-7 : 2012	SOUND SYSTEM EQUIPMENT - PART 7: HEADPHONES AND EARPHONES
BS EN 61947-2:2002	Electronic projection. Measurement and documentation of key performance criteria Variable resolution projectors
17/30356590 DC : DRAFT AUG 2017	BS ISO 10494 - TURBINES AND TURBINE SETS - MEASUREMENT OF EMITTED AIRBORNE NOISE - ENGINEERING/SURVEY METHOD
DIN ISO 15665:2011-02	Acoustics - Acoustic insulation for pipes,valves and flanges (ISO 15665:2003 + Cor. 1:2004)
BS EN 62121:2001	Methods of measurement for minidisc recorders/players
ANSI S12-5:2006	ACOUSTICS - REQUIREMENTS FOR THE PERFORMANCE AND CALIBRATION OF REFERENCE SOUND SOURCES USED FOR THE DETERMINATION OF SOUND POWER LEVELS
BS EN ISO 9295:2015	Acoustics. Determination of high-frequency sound power levels emitted by machinery and equipment
ANSI S12-5 : 2006 : R2011	ACOUSTICS - REQUIREMENTS FOR THE PERFORMANCE AND CALIBRATION OF REFERENCE SOUND SOURCES USED FOR THE DETERMINATION OF SOUND POWER LEVELS
NF EN 50134-5 : 2005	ALARM SYSTEMS - SOCIAL ALARM SYSTEMS - PART 5: INTERCONNECTIONS AND COMMUNICATIONS
ANSI S12.10 : 2002	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
ISO 10494:1993	Gas turbines and gas turbine sets Measurement of emitted airborne noise Engineering/survey method
ANSI/ASA S12.53 PART 1 : 2011(R2016)	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL MOVABLE SOURCES IN REVERBERANT FIELDS - PART 1: COMPARISON METHOD FOR A HARD-WALLED TEST ROOM
I.S. EN 13141-11:2015	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 11: SUPPLY VENTILATION UNITS
ANSI S12.32 : 0	PRECISION METHODS FOR THE DETERMINATION OF SOUND POWER LEVELS OF DISCRETE-FREQUENCY AND NARROW-BAND NOISE SOURCES IN REVERBERATION ROOMS
DIN EN ISO 17201-3:2010-06	ACOUSTICS - NOISE FROM SHOOTING RANGES - PART 3: GUIDELINES FOR SOUND PROPAGATION CALCULATIONS
ANSI S12.50 : 2002	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
I.S. EN ISO 15186-3:2010	ACOUSTICS - MEASUREMENT OF SOUND INSULATION IN BUILDINGS AND OF BUILDING ELEMENTS USING SOUND INTENSITY - PART 3: LABORATORY MEASUREMENTS AT LOW FREQUENCIES
ISO 13347-2:2004	Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 2: Reverberant room method
DIN EN ISO 11204:2010-10	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS
UNI EN ISO 17201-3 : 2010	ACOUSTICS - NOISE FROM SHOOTING RANGES - PART 3: GUIDELINES FOR SOUND PROPAGATION CALCULATIONS
I.S. EN 27574-3:1991	ACOUSTICS - STATISTICAL METHODS FOR DETERMINING AND VERIFYING STATED NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT - PART 3: SIMPLE (TRANSITION) METHOD FOR STATED VALUES FOR BATCHES OF MACHINES
CEN ISO/TR 22100-1:2017	Safety of machinery - Relationship with ISO 12100 - Part 1: How ISO 12100 relates to type-B and type-C standards (ISO/TR 22100-1:2015)
I.S. EN ISO 3382-3:2012	ACOUSTICS - MEASUREMENT OF ROOM ACOUSTIC PARAMETERS - PART 3: OPEN PLAN OFFICES (ISO 3382-3:2012)
ANSI S1.17-1 : 2014	MICROPHONE WINDSCREENS - PART 1: TEST PROCEDURES FOR MEASUREMENTS OF INSERTION LOSS IN STILL AIR
I.S. EN 16430-1:2014	FAN ASSISTED RADIATORS, CONVECTORS AND TRENCH CONVECTORS - PART 1: TECHNICAL SPECIFICATIONS AND REQUIREMENTS
17/30339487 DC : 0	BS EN 13053 - VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
PD CEN ISO/TR 22100-1:2017	Safety of machinery. Relationship with ISO 12100 How ISO 12100 relates to type-B and type-C standards
17/30361327 DC : 0	BS EN 13487 - HEAT EXCHANGER - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS AND DRY COOLERS - SOUND MEASUREMENT
IEC 62851-3:2014	Alarm and electronic security systems - Social alarm systems - Part 3: Local unit and controller
ECMA/TR 107 : 3ED 2017	AN OPTIONAL ALTERNATE BACKGROUND NOISE CORRECTION SENSITIVE TO THE STEADINESS OF BACKGROUND NOISE
ECMA/TR 70 : 3ED 2004	PRODUCT-RELATED ENVIRONMENTAL DECLARATION
ASTM E 1704 : 1995	Standard Guide for Specifying Acoustical Performance of Sound-Isolating Enclosures
ANSI/ASA S12.58:2012(R2019)	SOUND POWER LEVEL DETERMINATION FOR SOURCES USING A SINGLE-SOURCE POSITION
ISO/TR 22100-1:2015	Safety of machinery Relationship with ISO 12100 Part 1: How ISO 12100 relates to type-B and type-C standards
ISO 1680-1:1986	Acoustics Test code for the measurement of airborne noise emitted by rotating electrical machinery Part 1: Engineering method for free-field conditions over a reflecting plane
ISO 10302-1:2011	Acoustics — Measurement of airborne noise emitted and structure-borne vibration induced by small air-moving devices — Part 1: Airborne noise measurement
EN ISO 17201-3:2010	Acoustics - Noise from shooting ranges - Part 3: Guidelines for sound propagation calculations (ISO 17201-3:2010)
EN 12012-1:2007+A1:2008	Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators
I.S. EN 62075:2012	AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN (IEC 62075:2012 (EQV))
ISO 15665:2003	Acoustics — Acoustic insulation for pipes, valves and flanges
I.S. EN 60268-7:2011	SOUND SYSTEM EQUIPMENT - PART 7: HEADPHONES AND EARPHONES
EN ISO 11200:2014	Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:2014)
I.S. EN ISO 11200:2014	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO/DIS 11200:2012)
DIN EN ISO 14257:2011-11	Acoustics - Measurement and parametric description of of spatial sound distribution curves in workrooms for evaluation of their acoustical performance (ISO 14257:2001)
DIN EN ISO 11689:1997-03	ACOUSTICS - PROCEDURE FOR THE COMPARISON OF NOISE EMISSION-DATA FOR MACHINERY AND EQUIPMENT
BS EN ISO 1680:2013	Acoustics. Test code for the measurement of airborne noise emitted by rotating electrical machines
UNE-EN ISO 3747:2010	Acoustics - Determination of sound power levels of noise sources using sound pressure - Comparison method in situ (ISO 3747:2000)
BS EN 15036-1:2006	Heating boilers. Test regulations for airborne noise emissions from heat generators Airborne noise emissions from heat generators
BS EN ISO 11689 : 1997	ACOUSTICS - PROCEDURE FOR THE COMPARISON OF NOISE-EMISSION DATA FOR MACHINERY AND EQUIPMENT
BS EN ISO 10821 : 2005	INDUSTRIAL SEWING MACHINES - SAFETY REQUIREMENTS FOR SEWING MACHINES, UNITS AND SYSTEMS
BS EN ISO 5136:2009	Acoustics. Determination of sound power radiated into a duct by fans and other air-moving devices. In-duct method
ISO 10821:2005	Industrial sewing machines Safety requirements for sewing machines, units and systems
ISO 3382:1997	Acoustics — Measurement of the reverberation time of rooms with reference to other acoustical parameters
ISO 3743-1:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room
ISO 9614-3:2002	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning
BS EN ISO 6926:2016	Acoustics. Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels
ISO 11691:1995	Acoustics Measurement of insertion loss of ducted silencers without flow Laboratory survey method
IEC 60268-7:2010	Sound system equipment - Part 7: Headphones and earphones
ISO 3744:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
ISO 11202:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
BS EN ISO 9614-1:2009	Acoustics. Determination of sound power levels of noise sources using sound intensity Measurement at discrete points
BS EN ISO 11690-1:1997	Acoustics. Recommended practice for the design of low-noise workplaces containing machinery Noise control strategies
EN 50134-3:2012/AC:2015	Alarm systems - Social alarm systems - Part 3: Local unit and controller
BS EN 12012-3 : 2001	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 3: SAFETY REQUIREMENTS FOR SHREDDERS
BS EN ISO 11203:2009	Acoustics. Noise emitted by machinery and equipment. Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
UNI EN ISO 11200 : 2014	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS
ISO 7574-2:1985	Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 2: Methods for stated values for individual machines
ISO 11200:2014	Acoustics Noise emitted by machinery and equipment Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions
ISO 7574-3:1985	Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 3: Simple (transition) method for stated values for batches of machines
UNE-EN ISO 3743-2:2010	Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)
ISO 5135:1997	Acoustics Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room
ISO 12001:1996	Acoustics — Noise emitted by machinery and equipment — Rules for the drafting and presentation of a noise test code
ISO 14163:1998	Acoustics — Guidelines for noise control by silencers
UNI EN 13053 : 2011	VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
UNE-EN ISO 7235:2010	Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss (ISO 7235:2003)
ISO/TS 7849-1:2009	Acoustics — Determination of airborne sound power levels emitted by machinery using vibration measurement — Part 1: Survey method using a fixed radiation factor
ISO 1680:2013	Acoustics — Test code for the measurement of airborne noise emitted by rotating electrical machines
ISO 9614-2:1996	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning
ISO 3382-1:2009	Acoustics — Measurement of room acoustic parameters — Part 1: Performance spaces
ISO 9614-1:1993	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points
IEC 60268-5:2003+AMD1:2007 CSV	Sound system equipment - Part 5: Loudspeakers
ISO 11957:1996	Acoustics — Determination of sound insulation performance of cabins — Laboratory and in situ measurements
ISO 7235:2003	Acoustics — Laboratory measurement procedures for ducted silencers and air-terminal units — Insertion loss, flow noise and total pressure loss
UNE-EN ISO 3744:2011	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
IEC 60704-1:2010	Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 1: General requirements
BS EN 12354-5:2009	Building acoustics. Estimation of acoustic performance of building from the performance of elements Sounds levels due to the service equipment
UNE-EN ISO 9614-3:2010	Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurement by scanning (ISO 9614-3:2002)
UNE-EN ISO 12001:2010	Acoustics - Noise emitted by machinery and equipment - Rules for the drafting and presentation of a noise test code (ISO 12001:1996)
UNE-EN ISO 11546-2:2010	Acoustics - Determination of sound insulation performances of enclosures - Part 2: Measurements in situ (for acceptance and verification purposes) (ISO 11546-2:1995)
IEC 62075:2012	Audio/video, information and communication technology equipment - Environmentally conscious design
ISO 14257:2001	Acoustics — Measurement and parametric description of spatial sound distribution curves in workrooms for evaluation of their acoustical performance
ISO 3382-3:2012	Acoustics Measurement of room acoustic parameters Part 3: Open plan offices
BS EN 13487:2003	Heat exchangers. Forced convection air cooled refrigerant condensers and dry coolers. Sound measurement
BS EN ISO 3746:2009	Acoustics. Determination of sound power levels of noise sources using sound pressure. Survey method using an enveloping measurement surface over a reflecting plane
BS EN ISO 3743-1:2009	Acoustics. Determination of sound power levels of noise sources. Engineering methods for small, movable sources in reverberant fields Comparison method for hard-walled test rooms
IEC 62121:2001	Methods of measurement for minidisc recorders/players
ISO 15186-3:2002	Acoustics Measurement of sound insulation in buildings and of building elements using sound intensity Part 3: Laboratory measurements at low frequencies
UNE-EN 60268-7:2013	Sound system equipment -- Part 7: Headphones and earphones
UNE-EN ISO 3743-1:2011	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
IEC 60034-9:2003+AMD1:2007 CSV	Rotating electrical machines - Part 9: Noise limits
UNE-EN 13141-6:2015	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling
UNE-EN ISO 3746:2010	Acoustics - Determination of sound power levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:1995, including Cor 1:1995)
BS EN ISO 3747:2010	Acoustics. Determination of sound power levels and sound energy levels of noise sources using sound pressure. Engineering/survey methods for use in situ in a reverberant environment
ONORM EN 13053 : 2011	VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
BS EN ISO 11204:2010	Acoustics. Noise emitted by machinery and equipment. Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
IEC 60349-4:2012	Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
BS EN ISO 11200:2014	Acoustics. Noise emitted by machinery and equipment. Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions
IEC 60349-1:2010	Electric traction - Rotating electrical machines for rail and road vehicles - Part 1: Machines other than electronic converter-fed alternating current motors
UNE-EN 60349-1:2011	Electric traction - Rotating electrical machines for rail and road vehicles -- Part 1: Machines other than electronic converter-fed alternating current motors
BS EN ISO 14163:1998	Acoustics. Guidelines for noise control by silencers
BS EN ISO 4871:2009	Acoustics. Declaration and verification of noise emission values of machinery and equipment
BS EN ISO 12001:2009	Acoustics. Noise emitted by machinery and equipment. Rules for the drafting and presentation of a noise test code
BS EN 13141-8:2014	Ventilation for buildings. Performance testing of components/products for residential ventilation Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room
UNE-EN ISO 4871:2010	Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
ISO 15186-1:2000	Acoustics Measurement of sound insulation in buildings and of building elements using sound intensity Part 1: Laboratory measurements
IEC 61947-1:2002	Electronic projection - Measurement and documentation of key performance criteria - Part 1: Fixed resolution projectors
EN 15657-1:2009	Acoustic properties of building elements and of buildings - Laboratory measurement of airborne and structure borne sound from building equipment - Part 1: Simplified cases where the equipment mobilities are much higher than the receiver mobilities, taking whirlpool baths as an example
EN ISO 11957:2009	Acoustics - Determination of sound insulation performance of cabins - Laboratory and in situ measurements (ISO 11957:1996)
EN 16430-1:2014	Fan assisted radiators, convectors and trench convectors - Part 1: Technical specifications and requirements
EN ISO 9614-2:1996	Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 2: Measurement by scanning (ISO 9614-2:1996)
EN ISO 3743-1:2010	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
EN ISO 3743-2:2009	Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)
EN ISO 15186-3:2010	Acoustics - Measurement of sound insulation in buildings and of building elements using sound intensity - Part 3: Laboratory measurements at low frequencies (ISO 15186-3:2002)
EN ISO 12001:2009	Acoustics - Noise emitted by machinery and equipment - Rules for the drafting and presentation of a noise test code (ISO 12001:1996)
EN 27574-1:1988	Acoustics - Statistical methods for determining and verifying stated noise emission values of machinery and equipment - Part 1: General considerations and definitions (ISO 7574-1:1985)
EN 27574-3:1988	Acoustics - Statistical methods for determining and verifying stated noise emission values of machinery and equipment - Part 3: Simple (transition) method for stated values for batches of machines (ISO 7574-3:1985)
EN ISO 11201:2010	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 9614-1:2009	Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993)
EN 27574-2:1988	Acoustics - Statistical methods for determining and verifying stated noise emission values of machinery and equipment - Part 2: Methods for stated values for individual machines (ISO 7574-2:1985)
EN ISO 9614-3:2009	Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurement by scanning (ISO 9614-3:2002)
EN ISO 3382 : 2000	ACOUSTICS - MEASUREMENT OF THE REVERBERATION TIME OF ROOMS WITH REFERENCE TO OTHER ACOUSTICAL PARAMETERS
EN ISO 9295:2015	Acoustics - Determination of high-frequency sound power levels emitted by machinery and equipment (ISO 9295:2015)
EN ISO 3382-1:2009	Acoustics - Measurement of room acoustic parameters - Part 1: Performance spaces (ISO 3382-1:2009)
EN 16286-2:2013	Railway applications - Gangway systems between vehicles - Part 2: Acoustic measurements
EN ISO 1680:2013	Acoustics - Test code for the measurement of airborne noise emitted by rotating electrical machines (ISO 1680:2013)
EN 16583:2015	Heat exchangers - Hydronic room fan coils units - Determination of the sound power level
EN ISO 5136:2009	Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method (ISO 5136:2003)
EN ISO 14257:2001	Acoustics - Measurement and parametric description of spatial sound distribution curves in workrooms for evaluation of their acoustical performance (ISO 14257:2001)
EN ISO 7235:2009	Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss (ISO 7235:2003)
EN ISO 11546-1:2009	Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)
EN ISO 3744:2010	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN ISO 14163:1998	Acoustics - Guidelines for noise control by silencers (ISO 14163:1998)
EN ISO 3747:2010	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010)
EN ISO 4871:2009	Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
ENV 1397 : 1994	HEAT EXCHANGERS - HYDRONIC ROOM FAN COIL UNITS - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
EN ISO 11204:2010	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
EN 15036-1:2006	Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1: Airborne noise emissions from heat generators
UNE-EN 62075:2013	Audio/video, information and communication technology equipment - Environmentally conscious design
BS ISO 15186-3 : 2002	ACOUSTICS - MEASUREMENT OF SOUND INSULATION IN BUILDINGS AND OF BUILDING ELEMENTS USING SOUND INTENSITY - PART 3: LABORATORY MEASUREMENTS AT LOW FREQUENCIES
BS 4196-0:1981	Sound power levels of noise sources Guide for the use of basic standards and for the preparation of noise test codes
ISO 27327-2:2014	Fans — Air curtain units — Part 2: Laboratory methods of testing for sound power
12/30240135 DC : 0	BS ISO 11200 - ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS
BS EN 12102:2013	Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling. Measurement of airborne noise. Determination of the sound power level
BS ISO 23600:2007	Assistive products for persons with vision impairments and persons with vision and hearing impairments. Acoustic and tactile signals for pedestrian traffic lights
13/30264708 DC : 0	BS EN ISO 9295 - ACOUSTICS - DETERMINATION OF HIGH-FREQUENCY SOUND POWER LEVELS EMITTED BY MACHINERY AND EQUIPMENT
ANSI/ASA S3.36:2012(R2018)	SPECIFICATION FOR A MANIKIN FOR SIMULATED IN-SITU AIRBORNE ACOUSTIC MEASUREMENTS
DIN EN ISO 15186-3:2010-12	Acoustics - Measurement of sound insulation in buildings and of building elements using sound intensity - Part 3: Laboratory measurements at low frequencies (ISO 15186-3:2002)
DIN EN ISO 9295:2015-09	ACOUSTICS - DETERMINATION OF HIGH-FREQUENCY SOUND POWER LEVELS EMITTED BY MACHINERY AND EQUIPMENT (ISO 9295:2015)
ISO/TR 7849:1987	Acoustics Estimation of airborne noise emitted by machinery using vibration measurement
DIN EN ISO 11203:2010-01	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)
BS PD ISO/TR 22100-1 : 2015	SAFETY OF MACHINERY - RELATIONSHIP WITH ISO 12100 - PART 1: HOW ISO 12100 RELATES TO TYPE-B AND TYPE-C STANDARDS
I.S. EN 12102-1:2017	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS, PROCESS CHILLERS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS - DETERMINATION OF THE SOUND POWER LEVEL - PART 1: AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS FOR SPACE HEATING AND COOLING, DEHUMIDIFIERS AND PROCESS CHILLERS
BS EN 16286-2:2013	Railway applications. Gangway systems between vehicles Acoustic measurements
BS EN 61947-1:2002	Electronic projection. Measurement and documentation of key performance criteria Fixed resolution projectors
17/30332536 DC : 0	BS EN 13141-5 - VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 5: COWLS AND ROOF OUTLET TERMINAL DEVICES
I.S. EN 60704-1:2010	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE NOISE - PART 1: GENERAL REQUIREMENTS (IEC 60704-1:2010 (EQV))
DIN EN 13141-11:2015-07	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 11: SUPPLY VENTILATION UNITS
DIN EN ISO 3745:2012-07	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS (ISO 3745:2012 + AMD 1:2017)
11/30206274 DC : 0	BS EN 60349-4 - ELECTRIC TRACTION ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
BS 4196-7:1988	Sound power levels of noise sources Survey method for determination of sound power levels of noise sources using a reference sound source
ONORM EN ISO 7779 : 2010	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
AHRI 280 : 1995	REQUIREMENTS FOR THE QUALIFICATION OF REVERBERATION ROOMS IN THE 63 HZ OCTAVE BAND
BS 848-2.5(2003) : 2003	ACOUSTICS - DETERMINATION OF SOUND POWER RADIATED INTO A DUCT BY FANS AND OTHER AIR-MOVING DEVICES - IN-DUCT METHOD
ECMA 108 : 6ED 2016	DETERMINATION OF HIGH-FREQUENCY SOUND POWER LEVELS EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT
BS EN 50134-3:2012	Alarm systems. Social alarm systems Local unit and controller
I.S. EN 60349-2:2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
I.S. EN ISO 17201-3:2010	ACOUSTICS - NOISE FROM SHOOTING RANGES - PART 3: GUIDELINES FOR SOUND PROPAGATION CALCULATIONS
BS EN 60034-9:2005	Rotating electrical machines Noise limits
09/30182101 DC : 0	BS EN 60349-1 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTOR-FED ALTERNATING CURRENT MOTORS
CEI EN 62075 : 2013	AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN
DIN EN ISO 3746:2011-03	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
ANSI S12.53/1 : 2011	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL MOVABLE SOURCES IN REVERBERANT FIELDS - PART 1: COMPARISON METHOD FOR A HARD-WALLED TEST ROOM
I.S. EN 61096:1993	METHODS OF MEASURING THE CHARACTERISTICS OF REPRODUCING EQUIPMENT FOR DIGITAL AUDIO COMPACT DISCS
I.S. EN 27574-2:1991	ACOUSTICS - STATISTICAL METHODS FOR DETERMINING AND VERIFYING STATED NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT - PART 2: METHODS FOR STATED VALUES FOR INDIVIDUAL MACHINES
I.S. EN ISO 17201-1:2005	ACOUSTICS - NOISE FROM SHOOTING RANGES - PART 1: DETERMINATION OF MUZZLE BLAST BY MEASUREMENT
ISO 23600:2007	Assistive products for persons with vision impairments and persons with vision and hearing impairments Acoustic and tactile signals for pedestrian traffic lights
ISO 10302:1996	Acoustics Method for the measurement of airborne noise emitted by small air-moving devices
ANSI S12.54:2011	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
ANSI S12.53/2 : 1999 : R2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
ANSI/ASA S12.57 : 2011(R2016)	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
ANSI/ASA S12.10 PART 2 : 2011	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT - PART 2: DECLARATION OF NOISE EMISSION LEVELS
ANSI S12.50 : 2002 : R2012	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
ANSI S12.55 : 2012	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS
ANSI S3.36 : 2012	SPECIFICATION FOR A MANIKIN FOR SIMULATED IN-SITU AIRBORNE ACOUSTIC MEASUREMENTS
ANSI S12.50 : 2002 : R2007	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
ANSI S12.56 : 2011	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - SURVEY METHOD USING AN ENVELOPING MEASUREMENT SURFACE OVER A REFLECTING PLANE
ANSI/ASA S12.10 PART 1 : 2010	ACOUSTICS - MEASUREMENT OF AIRBORNE NOISE EMITTED BY INFORMATION TECHNOLOGY AND TELECOMMUNICATIONS EQUIPMENT - PART 1: DETERMINATION OF SOUND POWER LEVEL AND EMISSION SOUND PRESSURE LEVEL
UNI EN ISO 17201-1 : 2006	ACOUSTICS - NOISE FROM SHOOTING RANGES - PART 1: DETERMINATION OF MUZZLE BLAST BY MEASUREMENT
EN 12102-1:2017	Air conditioners, liquid chilling packages, heat pumps, process chillers and dehumidifiers with electrically driven compressors - Determination of the sound power level - Part 1: Air conditioners, liquid chilling packages, heat pumps for space heating and cooling, dehumidifiers and process chillers
ASTM F 2544 : 2011	Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units
ASTM E 1704 : 1995 : R2010	Standard Guide for Specifying Acoustical Performance of Sound-Isolating Enclosures
ISO 13347-1:2004	Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 1: General overview
EN 13053:2006+A1:2011	Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
I.S. EN 12012-1:2007	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS
DIN EN ISO 3743-1:2011-01	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
UNE-EN ISO 11201:2010	Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Engineering method in an essentially free field over a reflecting plane (ISO 11201:1995, including Cor 1:1997)
OVE/ONORM EN 60268-7 : 2011	SOUND SYSTEM EQUIPMENT - PART 7: HEADPHONES AND EARPHONES (IEC 60268-7:2010)
DIN EN ISO 9614-1:2009-11	Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993)
DIN EN ISO 3743-2:2009-11	Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)
UNE-EN 13141-8:2015	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room
BS EN ISO 11202:2010	Acoustics. Noise emitted by machinery and equipment. Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
ISO/TS 7849-2:2009	Acoustics — Determination of airborne sound power levels emitted by machinery using vibration measurement — Part 2: Engineering method including determination of the adequate radiation factor
ISO 11690-1:1996	Acoustics Recommended practice for the design of low-noise workplaces containing machinery Part 1: Noise control strategies
PD ISO/TR 18569:2004	Safety of machinery. Guidelines for the understanding and use of safety of machinery standards.
ISO 9295:2015	Acoustics Determination of high-frequency sound power levels emitted by machinery and equipment
UNE-EN 13141-7:2011	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings
UNE-EN ISO 11957:2010	Acoustics - Determination of sound insulation performance of cabins - Laboratory and in situ measurements (ISO 11957:1996)
BS EN 12012-2 : 2001	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
UNE-EN 13053:2007	Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
BS EN ISO 3745 : 2012	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS
BS EN ISO 9614-2:1997	Acoustics. Determination of sound power levels of noise sources using sound intensity Measurement by scanning
BS EN ISO 9614-3:2009	Acoustics. Determination of sound power levels of noise sources using sound intensity Precision method for measurement by scanning
BS EN 13141-7:2010	Ventilation for buildings. Performance testing of components/products for residential ventilation Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings
ISO 11201:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
BS EN 13141-6:2014	Ventilation for buildings. Performance testing of components/products for residential ventilation Exhaust ventilation system packages used in a single dwelling
BS EN ISO 3743-2:1997	Acoustics. Determination of sound power levels of noise sources. Engineering methods for small, movable sources in reverberant fields Methods for special reverberation test rooms
DIN EN 12102:2013-10	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
DIN EN ISO 3745:2017-10	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS (ISO 3745:2012 + AMD 1:2017)
EN 62075:2012/AC:2013	AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN (IEC 62075:2012)
EN 13141-6:2014	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling
EN ISO 3382-3:2012	Acoustics - Measurement of room acoustic parameters - Part 3: Open plan offices (ISO 3382-3:2012)
DIN EN ISO 12001:2010-01	Acoustics - Noise emitted by machinery and equipment - Rules for the drafting and presentation of a noise test code (ISO 12001:1996)
EN 60349-4:2013	Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
EN 60268-5:2003/A1:2009	SOUND SYSTEM EQUIPMENT - PART 5: LOUDSPEAKERS
EN 61947-2:2002	Electronic projection - Measurement and documentation of key performance criteria - Part 2: Variable resolution projectors
DIN EN ISO 15186-1:2003-12	ACOUSTICS - MEASUREMENT OF SOUND INSULATION IN BUILDINGS AND OF BUILDING ELEMENTS USING SOUND INTENSITY - PART 1: LABORATORY MEASUREMENTS
EN 60349-1:2010	Electric traction - Rotating electrical machines for rail and road vehicles - Part 1: Machines other than electronic converter-fed alternating current motors
DIN EN ISO 5136:2009-11	Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method (ISO 5136:2003)
DIN EN ISO 11546-1:2010-01	Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)
EN 60704-2-3:2002/A1:2005	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE ACOUSTICAL NOISE - PART 2-3: PARTICULAR REQUIREMENTS FOR DISHWASHERS
NF EN ISO 11203 : 2009	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS FROM THE SOUND POWER LEVEL
DIN EN 12012-1:2010-02	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS
EN 60349-2:2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
ONORM EN 16286-2 : OCT 2013	RAILWAY APPLICATIONS - GANGWAY SYSTEMS BETWEEN VEHICLES - PART 2: ACOUSTIC MEASUREMENTS
AHRI 1120 : 2012	ACOUSTICAL TEST METHODS AND SOUND POWER RATING PROCEDURES FOR TRANSPORT REFRIGERATION EQUIPMENT
UNE-EN ISO 11204:2010 V2	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
UNE-EN ISO 11202:2010 V2	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
BS 4196-3:1991	Sound power levels of noise sources Engineering methods for determination of sound power levels for sources in special reverberation test rooms

ISO 7574-2:1985	Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 2: Methods for stated values for individual machines
AS 5339:2019	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment
ISO 4871:1996	Acoustics — Declaration and verification of noise emission values of machinery and equipment
IEC 61183:1994	Electroacoustics - Random-incidence and diffuse-field calibration of sound level meters
ISO 12001:1996	Acoustics — Noise emitted by machinery and equipment — Rules for the drafting and presentation of a noise test code
AS 5337:2019	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane
AS 5102.1:2019	Performance of household electrical appliances - Swimming pool pump-units Measurement of energy consumption and performance
ISO 3744:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
ISO 354:2003	Acoustics — Measurement of sound absorption in a reverberation room
ISO 3743-2:1994	Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms
ISO 3382-2:2008	Acoustics Measurement of room acoustic parameters Part 2: Reverberation time in ordinary rooms
ISO 7574-4:1985	Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 4: Methods for stated values for batches of machines
ISO/TR 25417:2007	Acoustics Definitions of basic quantities and terms
ISO 9614-1:1993	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points
IEC 60942:2003	Electroacoustics - Sound calibrators
ISO 9296:2017	Acoustics — Declared noise emission values of information technology and telecommunications equipment
AS 5336:2019	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for anechoic rooms and hemi - anechoic rooms
ISO 3747:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering/survey methods for use in situ in a reverberant environment
AS 5335:2019	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane
ISO 3740:2000	Acoustics Determination of sound power levels of noise sources Guidelines for the use of basic standards
AS ISO 9296:2019	Acoustics - Declared noise emission values of information technology and telecommunications equipment
ISO 9613-1:1993	Acoustics Attenuation of sound during propagation outdoors Part 1: Calculation of the absorption of sound by the atmosphere
ISO 9614-2:1996	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning
ISO 7574-1:1985	Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 1: General considerations and definitions
ISO 80000-8:2007	Quantities and units Part 8: Acoustics
ISO 9295:2015	Acoustics Determination of high-frequency sound power levels emitted by machinery and equipment
ISO 3746:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
AS 5333.1:2019	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields Comparison method for a hard-walled test room
ISO 6926:2016	Acoustics Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels
ISO 9614-3:2002	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning
ISO 7574-3:1985	Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 3: Simple (transition) method for stated values for batches of machines
AS ISO 9295:2019	Acoustics - Determination of high-frequency sound power levels emitted by machinery and equipment
ISO 3745:2012	Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms
AS 5333.2:2019	Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields Methods for special reverberation test rooms
IEC 61260:1995	Electroacoustics - Octave-band and fractional-octave-band filters
ISO/IEC Guide 98-3:2008	Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
ISO 3743-1:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Get in touch with us

Shopping Cart

ISO 3741:2010

Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation test rooms

Abstract

General Product Information

International Equivalents

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory