BS EN 61810-1:2015
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Electromechanical elementary relays General and safety requirements
Hardcopy , PDF
11-04-2020
English
23-05-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Influence quantities
5 Rated values
6 General provisions for testing
7 Documentation and marking
8 Heating
9 Basic operating function
10 Dielectric strength
11 Electrical endurance
12 Mechanical endurance
13 Clearances, creepage distances and solid insulation
14 Terminations
15 Sealing
16 Heat and fire resistance
Annex A (normative) - Explanations regarding relays
Annex B (informative) - Inductive contact loads
Annex C (normative) - Test set-up
Annex D (informative) - Special loads
Annex E (normative) - Heating test arrangement
Annex F (normative) - Measurement of clearances
and creepage distances
Annex G (normative) - Relation between rated impulse
voltage, nominal voltage and
overvoltage category
Annex H (normative) - Pollution degrees
Annex I (normative) - Proof tracking test
Annex J (informative) - Schematic diagram of families
of terminations
Annex K (normative) - Glow-wire test
Annex L (normative) - Ball pressure test
Annex M (informative) - Needle flame test
Annex N (informative) - Resistance for standard
soldering processes
Annex O (informative) - Risk assessment
Alphabetical list of terms
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Pertains to electromechanical elementary relays (non-specified time allor-nothing relays) for incorporation into low voltage equipment (circuits up to 1000 V alternate current or 1500 V direct current).
| Committee |
EPL/94
|
| DevelopmentNote |
Supersedes BS EN 60255-1.00 and 96/209430 DC (02/2003) Supersedes BS EN 61810-5 and supersedes 02/203604 DC. (06/2004) Supersedes 11/30258040 DC. (05/2015)
|
| DocumentType |
Standard
|
| Pages |
102
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 61810-1 : 2015 | Identical |
| IEC 61810-1:2015 | Identical |
| I.S. EN 61810-1:2015 | Identical |
| SN EN 61810-1 : 1998 | Identical |
| UNE-EN 61810-1:2009 | Identical |
| NF EN 61810-1 : 2015 | Identical |
| DIN EN 61810-1 : 2015 COR 2 2017 | Identical |
| EN 61810-1:2015/AC:2018-04 | Identical |
| UNE-EN 60255-1:2010 | Measuring relays and protection equipment -- Part 1: Common requirements |
| PD 5304:2005 | GUIDANCE ON SAFE USE OF MACHINERY |
| PD 5304:2000 | SAFE USE OF MACHINERY |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 60038:2009 | IEC standard voltages |
| IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
| IEC 61984:2008 | Connectors - Safety requirements and tests |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
| EN 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| EN 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| EN 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61210:2010 | Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements |
| EN 61760-1:2006 | SURFACE MOUNTING TECHNOLOGY - PART 1: STANDARD METHOD FOR THE SPECIFICATION OF SURFACE MOUNTING COMPONENTS (SMDS) |
| IEC 61760-1:2006 | Surface mounting technology - Part 1: Standard method for the specification of surface mounting components (SMDs) |
| IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
| ANSI B11 TR3 : 2000 | RISK ASSESSMENT AND RISK REDUCTION - A GUIDE TO ESTIMATE, EVALUATE AND REDUCE RISKS ASSOCIATED WITH MACHINE TOOLS |
| EN 60099-1:1994/A1:1999 | SURGE ARRESTERS - PART 1: NON-LINEAR RESISTOR TYPE GAPPED SURGE ARRESTERS FOR A.C. SYSTEMS |
| ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
| IEC 60695-2-13:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials |
| IEC 61810-7:2006 | Electromechanical elementary relays - Part 7: Test and measurement procedures |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| IEC 60999-1:1999 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
| HD 60364-4-442:2012 | Low-voltage electrical installations - Part 4-442: Protection for safety - Protection of low-voltage installations against temporary overvoltages due to earth faults in the high-voltage system and due to faults in the low voltage system |
| EN 60695-2-13:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014) |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| IEC 60695-2-12:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials |
| SEMI S10 : 2015E | SAFETY GUIDELINE FOR RISK ASSESSMENT AND RISK EVALUATION PROCESS |
| EN 60068-2-17:1994 | Environmental testing - Part 2: Tests - Test Q: Sealing |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| EN 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| IEC 60364-4-44:2007+AMD1:2015 CSV | Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances |
| IEC 60099-1:1991+AMD1:1999 CSV | Surge arresters - Part 1: Non-linear resistor type gapped surge arresters for a.c. systems |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60669-1:2017 | Switches for household and similar fixed-electrical installations - Part 1: General requirements |
| IEC 60664-5:2007 | Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| EN 61210:2010 | Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| EN 60999-1:2000 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included) |
| EN 61984:2009 | Connectors - Safety requirements and tests |
| IEC 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| EN 60664-4:2006/corrigendum:2006 | INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 4: CONSIDERATION OF HIGH-FREQUENCY VOLTAGE STRESS |
| ISO 14971:2007 | Medical devices Application of risk management to medical devices |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| EN 60664-5:2007 | Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm |
| IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| IEC 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| EN 60695-2-12:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014) |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN 60664-3:2017 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| EN 60038:2011 | CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED) |
| EN 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014) |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN 60721-3-3 : 95 AMD 2 97 | CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.