EN 61587-1:2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
Superseded date
25-02-2022
Superseded by
Published date
21-04-2017
Sorry this product is not available in your region.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Classification of environmental conditions
5 General
6 Climatic tests
7 Mechanical tests
8 Safety aspects
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
IEC 61587-1:2016: specifies environmental requirements, test set-up, as well as safety aspects for empty enclosures, i.e., cabinets, racks, subracks, chassis with an integrated subrack, and associated plug-in units under indoor condition use and transportation. The purpose of this standard is to establish defined levels of physical performance in order to meet certain requirements of storage, transport and final location conditions. It applies in whole or part only to the mechanical structures of cabinets, racks, subracks, chassis with an integrated subrack, and associated plug-in units, but it does not apply to electronic equipment. This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: total overhaul of Clause 7 "Mechanical tests" and compatibility with IEC 61587-5.Key words: Indoor use, Transportation Requirements, Cabinets, Racks, Chassis Racks
| Committee |
CLC/SR 48D
|
| DevelopmentNote |
Supersedes UNE EN 61587-1. (12/2014)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN 61587-1:2017 | Identical |
| BS EN 61587-1:2017 | Identical |
| NBN EN 61587-1 : 2012 | Identical |
| IEC 61587-1:2016 | Identical |
| I.S. EN 61587-1:2017 | Identical |
| SN EN 61587-1 : 2017 | Identical |
| NF EN 61587-1 : 2017 | Identical |
| CEI EN 61587-1 : 2012 | Identical |
| PN EN 61587-1 : 2017 | Identical |
| NEN EN IEC 61587-1 : 2017 | Identical |
| ONORM OVE EN 61587-1 : 2018 | Identical |
| PNE-FprEN 61587-1:2016 | Identical |
| DIN EN 61587-1 : 2018 | Identical |
| VDE 0687-587-1 : 2018-03 | Identical |
| BS EN 60297-5-103:2001 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Electrostatic discharge protection |
| BS EN 60297-5-101:2001 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Injector/extractor handle |
| CEI EN 61587-6 : 1ED 2017 | MECHANICAL STRUCTURES FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 SERIES - PART 6: SECURITY ASPECTS FOR INDOOR CABINETS |
| BS EN 60297-3-101:2004 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482,6 mm (19 in) series Subracks and associated plug-in units |
| BS EN 61969-3:2012 | Mechanical structures for electronic equipment. Outdoor enclosures Environmental requirements, tests and safety aspects |
| EN 61587-4:2012 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 4: Combination of performance levels for modular cabinets |
| EN 60917-2-4:2010 | Modular order for the development of mechanical structures for electronic equipment practices - Part 2-4: Sectional specification - Interface coordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in) |
| EN 60297-3-109 : 2016 | MECHANICAL STRUCTURES FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-109: DIMENSIONS OF CHASSIS FOR EMBEDDED COMPUTING DEVICES |
| EN 60297-3-101:2004 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units |
| EN 60297-3-105:2009 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-105: Dimensions and design aspects for 1U high chassis |
| BS EN 60297-3-105:2009 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482,6 mm (19 in) series Dimensions and design aspects for 1U high chassis |
| I.S. EN 61969-3:2012 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - OUTDOOR ENCLOSURES - PART 3: ENVIRONMENTAL REQUIREMENTS, TESTS AND SAFETY ASPECTS (IEC 61969-3:2011 (EQV)) |
| BS EN 60297-3-109:2016 | Mechanical structures for electrical and electronic equipment. Dimensions of mechanical structures of the 482,6 mm (19 in) series Dimensions of chassis for embedded computing devices |
| I.S. EN 60297-3-101:2004 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-101: SUBRACKS AND ASSOCIATED PLUG-IN UNITS |
| BS EN 61969-1:2012 | Mechanical structures for electronic equipment. Outdoor enclosures Design guidelines |
| BS EN 61587-4:2012 | Mechanical structures for electronic equipment. Tests for IEC 60917 and IEC 60297 series Combination of performance levels for modular cabinets |
| I.S. EN 60297-3-108:2015 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-108: DIMENSIONS OF R-TYPE SUBRACKS AND PLUG-IN UNITS (IEC 60297-3-108:2014) |
| CEI EN 61587-5 : 2014 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 - PART 5: SEISMIC TESTS FOR CHASSIS, SUBRACKS AND PLUG-IN UNITS |
| I.S. EN 60297-3-105:2009 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-105: DIMENSIONS AND DESIGN ASPECTS FOR 1U HIGH CHASSIS |
| I.S. EN 61587-4:2012 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 SERIES - PART 4: COMBINATION OF PERFORMANCE LEVELS FOR MODULAR CABINETS (IEC 61587-4:2012 (EQV)) |
| EN 61969-3:2012 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects |
| BS EN 60297-5-102:2001 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Electromagnetic shielding provision |
| I.S. EN 61587-6:2017 | MECHANICAL STRUCTURES FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 SERIES - PART 6: SECURITY ASPECTS FOR INDOOR CABINETS |
| BS EN 61587-6:2017 | Mechanical structures for electrical and electronic equipment. Tests for IEC 60917 and IEC 60297 series Security aspects for indoor cabinets |
| I.S. EN 60297-3-109:2016 | MECHANICAL STRUCTURES FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-109: DIMENSIONS OF CHASSIS FOR EMBEDDED COMPUTING DEVICES |
| BS EN 60297-5-104:2001 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Keying |
| BS EN 60297-5-100:2001 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Design overview |
| CEI EN 60297-3-101 : 2005 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-101: SUBRACKS AND ASSOCIATED PLUG-IN UNITS |
| EN 61587-6:2017 | Mechanical structures for electrical and electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 6: Security aspects for indoor cabinets |
| EN 61969-1:2012 | Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines |
| EN 60297-3-109:2016 | MECHANICAL STRUCTURES FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-109: DIMENSIONS OF CHASSIS FOR EMBEDDED COMPUTING DEVICES |
| CEI EN 61587-4 : 2013 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 SERIES - PART 4: COMBINATION OF PERFORMANCE LEVELS FOR MODULAR CABINETS |
| BS EN 60297-3-108:2015 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482,6 mm (19 in) series Dimensions of R-type subracks and plug-in units |
| BS EN 61587-5:2014 | Mechanical structures for electronic equipment. Tests for IEC 60917 and IEC 60297 Seismic tests for chassis, subracks and plug-in units |
| BS EN 60297-3-106:2010 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482,6 mm (19 in) series Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1 |
| BS EN 60297-5-105:2001 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Alignments and/or earth pin |
| CEI EN 61969-3 : 2012 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - OUTDOOR ENCLOSURES - PART 3: ENVIRONMENTAL REQUIREMENTS, TESTS AND SAFETY ASPECTS |
| I.S. EN 61587-5:2014 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 - PART 5: SEISMIC TESTS FOR CHASSIS, SUBRACKS AND PLUG-IN UNITS |
| I.S. EN 61969-1:2012 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - OUTDOOR ENCLOSURES - PART 1: DESIGN GUIDELINES (IEC 61969-1:2011 (EQV)) |
| BS EN 60297-5-107:2001 | Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Rear mounted plug-in units |
| CEI EN 60297-3-105 : 2010 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-105: DIMENSIONS AND DESIGN ASPECTS FOR 1U HIGH CHASSIS |
| BS EN 60917-2-4:2010 | Modular order for the development of mechanical structures for electronic equipment practices Sectional specification. Interface coordination dimensions for the 25 mm equipment practice. Adaptation dimensions for subracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in) |
| CEI EN 61969-1 : 2012 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - OUTDOOR ENCLOSURES - PART 1: DESIGN GUIDELINES |
| EN 60297-3-108:2015 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-108: Dimensions of R-type subracks and plug-in units |
| EN 61587-5:2014 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 5: Seismic tests for chassis, subracks and plug-in units |
| EN 60297-3-106:2010 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1 |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| EN 60917-2-2:1996 | Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 2: Detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units |
| IEC 60297-3-101:2004 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units |
| IEC 60654-4:1987 | Operating conditions for industrial-process measurement and control equipment. Part 4: Corrosive and erosive influences |
| EN 60297-3-100:2009 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets |
| IEC 60068-2-43:2003 | Environmental testing - Part 2-43: Tests - Test Kd: Hydrogen sulphide test for contacts and connections |
| IEC 61373:2010 | Railway applications - Rolling stock equipment - Shock and vibration tests |
| EN 61587-2:2011 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 - PART 2: SEISMIC TESTS FOR CABINETS AND RACKS (IEC 61587-2:2011) |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| EN 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| EN 61587-5:2014 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 5: Seismic tests for chassis, subracks and plug-in units |
| IEC 61587-2:2011 | Mechanical structures for electronic equipment - Tests for IEC 60917 and 60297 - Part 2: Seismic tests for cabinets and racks |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 60917-2-1:1993 | Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 1: Detail specification - Dimensions for cabinets and racks |
| IEC 60068-2-49:1983 | Basic environmental testing procedures - Part 2-49: Tests - Guidance to test Kc: Sulphur dioxide test for contacts and connections |
| EN 60297-3-107:2012 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-107: Dimensions of subracks and plug-in units, small form factor |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61587-3:2013 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets and subracks |
| EN 61373:2010/AC:2017-09 | RAILWAY APPLICATIONS - ROLLING STOCK EQUIPMENT - SHOCK AND VIBRATION TESTS (IEC 61373:2010) |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| IEC 61587-5:2013 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 5: Seismic tests for chassis, subracks and plug-in units |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| EN 60917-2-3 : 2006 | Modular order for the development of mechanical structures for electronic equipment practices - Part 2-3: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Extended detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units |
| EN 60068-2-64:2008 | ENVIRONMENTAL TESTING - PART 2-64: TESTS - TEST FH: VIBRATION, BROADBAND RANDOM AND GUIDANCE |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| EN 60297-3-101:2004 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units |
| EN 60654-4:1997 | Operating conditions for industrial-process measurement and control equipment - Part 4: Corrosive and erosive influences |
| IEC 60068-2-64:2008 | Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance |
| EN 61587-3:2013 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets and subracks |
| IEC 60297-3-108:2014 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-108: Dimensions of R-type subracks and plug-in units |
| EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60512-1-1:2002 | Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| IEC 62262:2002 | Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code) |
| IEC 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| IEC 60917-2-2:1994 | Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 2: Detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units |
| IEC 60297-3-107:2012 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-107: Dimensions of subracks and plug-in units, small form factor |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| EN 60297-3-108:2015 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-108: Dimensions of R-type subracks and plug-in units |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| EN 60917-2-1:1995 | Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 1: Detail specification - Dimensions for cabinets and racks |
| EN 60068-2-43:2003 | Environmental testing - Part 2-43: Tests - Test Kd: Hydrogen sulphide test for contacts and connections |
| EN 60068-2-11:1999 | Environmental testing - Part 2: Tests - Test Ka: Salt mist |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 61010-1:2010 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| EN 60512-1-1:2002 | Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination |
| IEC 60917-2-3:2006 | Modular order for the development of mechanical structures for electronic equipment practices - Part 2-3: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Extended detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units |
| IEC 61010-1:2010+AMD1:2016 CSV | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| IEC 60068-2-52:2017 | Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) |
| IEC 60297-3-100:2008 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets |
| EN 60721-3-3 : 95 AMD 2 97 | CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.