![header thumbnail](/images/publishers\iec_cover.gif)
IEC 60216-5:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\iec_cover.gif)
Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
18-11-2022
11-03-2008
FOREWORD
1 Scope
2 Normative references
3 Terms, definitions, symbols, units and abbreviations
3.1 Terms, abbreviations, and definitions
3.2 Symbols and units
3.3 Objectives of RTE determination
4 Experimental procedures
4.1 Selection of reference EIM
4.2 Selection of diagnostic test for extent of ageing
4.3 Ageing procedures
5 Calculation procedures
5.1 Thermal endurance data - Calculation of intermediate
parameters
5.2 Calculation of RTE
5.3 Statistical and numerical tests
5.3.1 Tests of IEC 60216-3
5.3.2 Precision of correlation time
5.3.3 Lower confidence interval of RTE
5.3.4 Extrapolation
6 Report
6.1 Results of statistical and numerical tests
6.2 Results
6.3 Report
7 Material testing by short-term thermal ageing
8 Insulation classification
Annex A (informative) Repeatability of correlation time
Annex B (informative) Thermal class assignment
Annex C (informative) Computer program
Annex D (informative) Selection of the reference EIM
Bibliography
IEC 60216-5 specifies the experimental and calculation procedures to be used for deriving the relative thermal endurance index of a material from experimental data obtained in accordance with the instructions of IEC 60216-1 and IEC 60216-2. The calculation procedures are supplementary to those of IEC 60216-3. Guidance is also given for assessment of thermal ageing after a single fixed time and temperature, without extrapolation. The experimental data may in principle be obtained using destructive, non-destructive or proof tests, although destructive tests have been much more extensively employed. Data obtained from non-destructive or proof tests may be "censored", in that measurement of times taken to reach the endpoint may have been terminated at some point after the median time but before all specimens have reached end-point (see IEC 60216-1). Guidance is given for preliminary assignment of a thermal class for an insulating material, based upon the thermal ageing performance. The calculation procedures of this standard also apply to the determination of the thermal class of an electrical insulation system when the thermal stress is the prevailing ageing factor. This third edition clarifies and corrects a few items and adds an Annex D which provides criteria for the selection of the reference (or reference EIM). The third edition provides instructions for deriving a provisional estimate of the temperature up to which a material may give satisfactory performance in an application (by comparative thermal ageing with a material of known performance). The contents of the corrigendum of December 2009 have been included in this copy.
Please be aware that the computer program provided in this publication is not compatible with the 64-bit version of Windows 7.
Committee |
TC 112
|
DevelopmentNote |
To be read in conjunction with IEC 60216-1, IEC 60216-2 and IEC 60216-3. (01/2003) Stability Date: 2016. (11/2012)
|
DocumentType |
Standard
|
Pages |
46
|
PublisherName |
International Electrotechnical Committee
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NEN EN IEC 60216-5 : 2008 | Identical |
SAC GB/T 11026-7 : 2014 | Identical |
VDE 0304-25 : 2009 | Identical |
BIS IS 8504-6 : 2012 | Identical |
CEI EN 60216-5 : 2012 | Identical |
EN 60216-5:2008 | Identical |
JIS C 2143-5:2013 | Identical |
OVE/ONORM EN 60216-5 : 2009 | Identical |
PNE-prEN 60216-5 | Identical |
UNE-EN 60216-5:2008 | Identical |
PN EN 60216-5 : 2008 | Identical |
BS EN 60216-5:2008 | Identical |
NF EN 60216-5 : 2008 | Identical |
DIN EN 60216-5 : 2009 | Identical |
BS 5691-5:1995 | Identical |
I.S. EN 60216-5:2008 | Identical |
CEI 15-51 : 1ED 1997 | Identical |
NFC 26 305 : 1993 | Identical |
BS 2782-1.135(1993) : 1993 AMD 10349 | METHODS OF TEST PLASTICS - THERMAL PROPERTIES - DETERMINATION OF THE TIME-TEMPERATURE LIMITS AFTER PROLONGED EXPOSURE TO HEAT |
05/30128627 DC : DRAFT FEB 2005 | IEC 60216-6 ED.2 - ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 6: DETERMINATION OF THERMAL ENDURANCE INDICES (TI AND RTE) OF AN INSULATING MATERIAL USING THE FIXED TIME FRAME METHOD |
15/30294124 DC : 0 | BS EN 60674-2 ED 2.0 - SPECIFICATION FOR PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
BS EN 60674-3-8 : 2011 | PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 8: BALANCED BIAXIALLY ORIENTED POLYETHYLENE NAPHTHALATE (PEN) FILMS USED FOR ELECTRICAL INSULATION (IEC 60674-3-8:2011) |
BS IEC 61858-2 : 2014 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 2: FORM-WOUND EIS |
CEI EN 60216-3 : 2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS |
PD IEC/TS 62446-3:2017 | Photovoltaic (PV) systems. Requirements for testing, documentation and maintenance Photovoltaic modules and plants. Outdoor infrared thermography |
I.S. EN 60085:2008 | ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION |
04/30116245 DC : DRAFT JUL 2004 | IEC 60216-4-1 ED.4 - GUIDE FOR THE DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - PART 4: AGEING OVENS |
BS EN 61858-2:2014 | Electrical insulation systems. Thermal evaluation of modifications to an established electrical insulation system (EIS) Form-wound EIS |
BS EN 60216-2:2005 | Electrical insulating materials. Thermal endurance properties Determination of thermal endurance properties of electrical insulating materials. Choice of test criteria |
DD IEC/TS 62332-1:2011 | Electrical insulation systems (EIS). Thermal evaluation of combined liquid and solid components General requirements |
08/30177750 DC : DRAFT FEB 2008 | BS EN 61857-1 - ELECTRICAL INSULATION SYSTEMS - PROCEDURES FOR THERMAL EVALUATION - PART 1: GENERAL REQUIREMENTS - LOW-VOLTAGE |
IEC TS 62332-2:2014 | Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 2: Simplified test |
I.S. EN 62109-1:2010 | SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS |
CEI EN 60034-18-21 : 2014 | ROTATING ELECTRICAL MACHINES - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION |
CEI EN 61857-1 : 2010 | ELECTRICAL INSULATION SYSTEMS - PROCEDURES FOR THERMAL EVALUATION - PART 1: GENERAL REQUIREMENTS - LOW-VOLTAGE |
I.S. EN 60034-18-31:2012 | ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012 (EQV)) |
I.S. EN 61858:2008 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS |
BS EN 61730-1 : 2007 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
I.S. EN 60034-18-21:2013 | ROTATING ELECTRICAL MACHINES - - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIREWOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION (IEC 60034-18-21:2012 (EQV)) |
NF EN 60216-2 : 2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
CSA C22.2 No. 0.17 : 2000 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
IEC 61730-1:2016 | Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction |
16/30330036 DC : 0 | BS EN 62788-2 - MEASUREMENT PROCEDURES FOR MATERIALS USED IN PHOTOVOLTAIC MODULES - PART 2: POLYMERIC MATERIALS USED FOR FRONTSHEETS AND BACKSHEETS |
IEC 60691:2015 | Thermal-links - Requirements and application guide |
IEC 60674-3-8:2011+AMD1:2016 CSV | Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 8: Balanced biaxially oriented polyethylene naphthalate (PEN) films used for electrical insulation |
EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
EN 60216-6:2006 | Electrical insulating materials - Thermal endurance properties - Part 6: Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method |
EN 60691:2016 | Thermal-links - Requirements and application guide |
EN 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
EN 60505:2011/AC:2017-03 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS (IEC 60505:2011/COR1:2017) |
EN 61858-2:2014 | Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 2: Form-wound EIS |
EN 60034-18-31 : 2012 | ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012) |
EN 60216-3-2:1995 | Guide for the determination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - Section 2: Calculations for incomplete data: proof test results up to and including the median time to end-point (equal test groups) |
BIS IS 8504-2 : 2013 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
PD IEC/TR 60493-2:2010 | Guide for the statistical analysis of ageing test data Validation of procedures for statistical analysis of censored normally distributed data |
PD IEC/TS 62332-3:2016 | Electrical insulation systems (EIS). Thermal evaluation of combined liquid and solid components Hermetic motor-compressors |
BS EN 60034-18-21:2013 | Rotating electrical machines Functional evaluation of insulation systems. Test procedures for wire-wound windings. Thermal evaluation and classification |
BS EN 60216-8:2013 | Electrical insulating materials. Thermal endurance properties Instructions for calculating thermal endurance characteristics using simplified procedures |
BS 3G 198-3:1994 | Sleeves for aircraft electric cables and equipment wires Specification for heat-shrinkable sleeving for binding, insulation and identification |
DIN EN 60216-3-2 : 1997 | GUIDE FOR THE DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS - SECTION 2: CALCULATIONS FOR INCOMPLETE DATA: PROOF TEST RESULTS UP TO AND INCLUDING THE MEDIAN TIME TO END-POINT (EQUAL TEST GROUPS) |
PD IEC/TS 60216-7-1:2015 | Electrical insulation materials. Thermal endurance properties Accelerated determination of relative thermal endurance using analytical test methods (RTE<sub>A</sub>). Instructions for calculations based on activation energy |
12/30273912 DC : 0 | BS EN 61858-2 - ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED EIS - PART-2: FORM-WOUND EIS |
BS EN 60085:2008 | Electrical insulation. Thermal evaluation and designation |
CSA C22.2 No. 0.17 : 2000 : R2013 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
BS EN 60216-6:2006 | Electrical insulating materials. Thermal endurance properties Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method |
BS EN 61857-1:2009 | Electrical insulation systems. Procedures for thermal evaluation General requirements. Low-voltage |
IEC TR 62392:2006 | Suitability of typical electrical insulating material (EIM) for polymer recycling |
IEC 60077-1 REDLINE : 2ED 2017 | RAILWAY APPLICATIONS - ELECTRIC EQUIPMENT FOR ROLLING STOCK - PART 1: GENERAL SERVICE CONDITIONS AND GENERAL RULES |
I.S. EN 60216-3:2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS |
BS EN 60310:2016 | Railway applications. Traction transformers and inductors on board rolling stock |
I.S. EN 60505:2011 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS |
I.S. EN 61858-2:2014 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 2: FORM-WOUND EIS |
I.S. EN 61857-1:2009 | ELECTRICAL INSULATION SYSTEMS - PROCEDURES FOR THERMAL EVALUATION - PART 1: GENERAL REQUIREMENTS - LOW-VOLTAGE |
IEC TS 62101:2005 | Electrical insulation systems - Short-time evaluation of combined thermal and electrical stresses |
IEC TR 60216-7-2:2016 | Electrical insulating materials - Thermal endurance properties - Part 7-2: Results of the round robin tests to validate procedures of IEC TS 60216-7-1 by non-isothermal kinetic analysis of thermogravimetric data |
I.S. EN 60077-1:2017 | RAILWAY APPLICATIONS - ELECTRIC EQUIPMENT FOR ROLLING STOCK - PART 1: GENERAL SERVICE CONDITIONS AND GENERAL RULES |
IEC TS 62332-3:2016 | Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 3: Hermetic motor-compressors |
IEC TS 62332-1:2011 | Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 1: General requirements |
IEC 62899-201:2016 | Printed electronics - Part 201: Materials - Substrates |
17/30355792 DC : 0 | BS EN 62790 AMENDMENT 1 - JUNCTION BOXES FOR PHOTOVOLTAIC MODULES - SAFETY REQUIREMENTS AND TESTS |
03/106712 DC : 0 | IEC 62326-3 ED.1.0 - PRINTED BOARDS - PART 3: SAFETY CERTIFICATION OF RIGID PRINTED CIRCUIT BOARDS FOR ELECTRONIC ASSEMBLIES |
BS 5691-1:1995 | Guide for the determination of thermal endurance properties of electrical insulating materials General guidelines for ageing procedures and evaluation of test results |
06/30146693 DC : DRAFT FEB 2006 | |
11/30244661 DC : 0 | BS EN 60493-1 - GUIDE FOR THE STATISTICAL ANALYSIS OF AGEING TEST DATA - PART 1: METHODS BASED ON MEAN VALUES OF NORMALLY DISTRIBUTED TEST RESULTS |
NF EN 61858 : 2009 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS |
04/30116267 DC : DRAFT JUL 2004 | IEC 61857-31 - ELECTRICAL INSULATION SYSTEMS - PART 31: PROCEDURES FOR SHORT TIME THERMAL EVALUATION |
CEI EN 60674-3-8 : 2012 | PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 8: BALANCED BIAXIALLY ORIENTED POLYETHYLENE NAPHTHALATE (PEN) FILMS USED FOR ELECTRICAL INSULATION |
BS EN 60216-4-1:2006 | Electrical insulating materials. Thermal endurance properties Ageing ovens - Single-chamber ovens |
12/30273916 DC : 0 | BS EN 61858-1 - ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED EIS - PART-1: WIRE-WOUND WINDING EIS |
BS EN 60034-18-31:2012 | Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Thermal evaluation and classification of insulation systems used in rotating machines |
08/30177151 DC : DRAFT JAN 2008 | BS EN 61858 - ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS |
NF EN 60674-3-8 : 2012 AMD 1 2017 | PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 8: BALANCED BIAXIALLY ORIENTED POLYETHYLENE NAPHTHALATE (PEN) FILMS USED FOR ELECTRICAL INSULATION |
NF EN 60085 : 2008 | ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION |
BS EN 61858-1:2014 | Electrical insulation systems. Thermal evaluation of modifications to an established electrical insulation system (EIS) Wire-wound winding EIS |
14/30271248 DC : 0 | BS EN 60310 ED 4.0 - RAILWAY APPLICATIONS - TRACTION TRANSFORMERS AND INDUCTORS ON BOARD ROLLING STOCK |
02/207211 DC : DRAFT JULY 2002 | IEC 60085 ED.3.0 - THERMAL EVALUATION AND CLASSIFICATION OF ELECTRICAL INSULATION |
15/30330425 DC : 0 | BS EN 60370 ED 2.0 - TEST PROCEDURE FOR THERMAL ENDURANCE OF INSULATING RESINS AND VARNISHES FOR IMPREGNATION PURPOSES - ELECTRIC BREAKDOWN METHODS |
IEC 60493-1:2011 | Guide for the statistical analysis of ageing test data - Part 1: Methods based on mean values of normally distributed test results |
BS EN 61858:2008 | Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS |
CSA C22.2 No. 0.17 : 2000 : R2004 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
PD IEC/TR 60216-7-2:2016 | Electrical insulating materials. Thermal endurance properties Results of the round robin tests to validate procedures of IEC TS 60216-7-1 by non-isothermal kinetic analysis of thermogravimetric data |
IEC TR 60493-2:2010 | Guide for the statistical analysis of ageing test data - Part 2: Validation of procedures for statistical analysis of censored normally distributed data |
CEI EN 60085 : 2009 | ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION |
NF EN 60216-6 : 2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 6: DETERMINATION OF THERMAL ENDURANCE INDICES (TI AND RTE) OF AN INSULATING MATERIAL USING THE FIXED TIME FRAME METHOD |
EN IEC 61730-1:2018/AC:2018-06 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2016) |
I.S. EN 60310:2016 | RAILWAY APPLICATIONS - TRACTION TRANSFORMERS AND INDUCTORS ON BOARD ROLLING STOCK |
IEEE 98-2002 | IEEE Standard for the Preparation of Test Procedures for the Thermal Evaluation of Solid Electrical Insulating Materials |
CEI EN 60034-18-31 : 2013 | ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES |
IEC 60076-12:2008 | Power transformers - Part 12: Loading guide for dry-type power transformers |
IEC 60034-18-22:2000 | Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions |
PD IEC/TS 62788-2:2017 | Measurement procedures for materials used in photovoltaic modules Polymeric materials. Frontsheets and backsheets |
IEC 60216-8:2013 | Electrical insulating materials - Thermal endurance properties - Part 8: Instructions for calculating thermal endurance characteristics using simplified procedures |
IEC TS 60216-7-1:2015 | Electrical insulation materials - Thermal endurance properties - Part 7-1: Accelerated determination of relative thermal endurance using analytical test methods (RTEA) - Instructions for calculations based on activation energy |
UNE-EN 62109-1:2011 | Safety of power converters for use in photovoltaic power systems -- Part 1: General requirements |
IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
09/30198417 DC : DRAFT JAN 2009 | BS EN 60505 - EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS |
14/30304003 DC : 0 | BS EN 62899-1 ED.1 - PRINTED ELECTRONICS - MATERIALS - PART 1: SUBSTRATES |
11/30246689 DC : 0 | BS EN 60216-8 - ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 8: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS USING SIMPLIFIED PROCEDURES |
BS EN 60505:2011 | Evaluation and qualification of electrical insulation systems |
CEI EN 60216-6 : 2007 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 6: DETERMINATION OF THERMAL ENDURANCE INDICES (TI AND RTE) OF AN INSULATING MATERIAL USING THE FIXED TIME FRAME METHOD |
PD IEC/TS 62332-2:2014 | Electrical insulation systems (EIS). Thermal evaluation of combined liquid and solid components Simplified test |
NF EN 60691 : 2016 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE |
I.S. EN 60216-8:2013 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 8: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS USING SIMPLIFIED PROCEDURES (IEC 60216-8:2013 (EQV)) |
I.S. EN 62864-1:2016 | RAILWAY APPLICATIONS - ROLLING STOCK - POWER SUPPLY WITH ONBOARD ENERGY STORAGE SYSTEM - PART 1: SERIES HYBRID SYSTEM |
BS IEC 62899-201 : 2016 | PRINTED ELECTRONICS - PART 201: MATERIALS - SUBSTRATES |
I.S. EN IEC 62688:2018 | CONCENTRATOR PHOTOVOLTAIC (CPV) MODULES AND ASSEMBLIES - SAFETY QUALIFICATION |
I.S. EN 61858-1:2014 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS |
I.S. EN IEC 61730-1:2018 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
I.S. EN 60216-6:2004 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 6: DETERMINATION OF THERMAL ENDURANCE INDICES (TI AND RTE) OF AN INSULATING MATERIAL USING THE FIXED TIME FRAME METHOD |
CEI EN 60505 : 2012 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS |
BS EN 60691:2016 | Thermal-links. Requirements and application guide |
CEI EN 60216-2 : 2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
BS EN 60216-3-2:1995 | Guide for the determination of thermal endurance properties of electrical insulating materials. Instructions for calculating thermal endurance characteristics Calculations for incomplete data: proof test results up to and including the median time to end-point (equal test groups) |
UNE-EN 62864-1:2017 | Railway applications - Rolling stock - Power supply with onboard energy storage system - Part 1: Series hybrid system |
UNE-EN 60034-18-31:2013 | Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines |
12/30272980 DC : 0 | BS EN 6XXXX-1 - ELECTRIC MOTOR-OPERATED HAND-HELD, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY - SAFETY - PART 1: GENERAL REQUIREMENTS |
BS EN ISO 2578:1999 | Plastics. Determination of the time-temperature limits after prolonged exposure to heat |
16/30296081 DC : 0 | BS EN 60077-1 ED. 2.0 - RAILWAY APPLICATIONS - ELECTRIC EQUIPMENT FOR ROLLING STOCK - PART 1: GENERAL SERVICE CONDITIONS AND GENERAL RULES |
ISO 2578:1993 | Plastics Determination of time-temperature limits after prolonged exposure to heat |
IEC 61857-1:2008 | Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage |
IEC 60505:2011 | Evaluation and qualification of electrical insulation systems |
BS EN 62109-1:2010 | Safety of power converters for use in photovoltaic power systems General requirements |
IEC 60216-6:2006 | Electrical insulating materials - Thermal endurance properties - Part 6: Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method |
IEC 61858-1:2014 | Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS |
IEC TS 62788-2:2017 | Measurement procedures for materials used in photovoltaic modules - Part 2: Polymeric materials - Frontsheets and backsheets |
IEC 61858-2:2014 | Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 2: Form-wound EIS |
IEC 60216-3:2006 | Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics |
IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
IEC 60034-18-21:2012 | Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification |
IEC 60034-18-31:2012 | Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines |
IEC 60310:2016 | Railway applications - Traction transformers and inductors on board rolling stock |
BS EN 60077-1:2017 | Railway applications. Electric equipment for rolling stock General service conditions and general rules |
16/30242287 DC : 0 | BS EN 62688 - CONCENTRATOR PHOTOVOLTAIC (CPV) MODULE AND ASSEMBLY SAFETY QUALIFICATION |
EN 62109-1 : 2010 | SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS |
EN ISO 2578 : 1998 | PLASTICS - DETERMINATION OF TIME-TEMPERATURE LIMITS AFTER PROLONGED EXPOSURE TO HEAT |
17/30352672 DC : 0 | BS IEC 62788-5-1 ED 1.0 - MEASUREMENT PROCEDURES FOR MATERIALS USED IN PHOTOVOLTAIC MODULES - 5-1: EDGE SEALS - SUGGESTED TEST METHODS FOR USE WITH EDGE SEAL MATERIALS |
EN 60216-3:2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS |
16/30350588 DC : 0 | BS PD IEC/TS 62446-3 ED 1.0 - PHOTOVOLTAIC (PV) SYSTEMS - REQUIREMENTS FOR TESTING, DOCUMENTATION AND MAINTENANCE - PART 3: OUTDOOR INFRARED THERMOGRAPHY OF PHOTOVOLTAIC MODULES AND PLANTS |
NF EN 60505 : 2011 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS |
IEC TS 62446-3:2017 | Photovoltaic (PV) systems - Requirements for testing, documentation and maintenance - Part 3: Photovoltaic modules and plants - Outdoor infrared thermography |
BS EN 60216-3:2006 | Electrical insulating materials. Thermal endurance properties Instructions for calculating thermal endurance characteristics |
BS IEC 60493-1:2011 | Guide for the statistical analysis of ageing test data Methods based on mean values of normally distributed test results |
NF EN 61730-1 : 2007 AMD 11 2015 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
CSA C22.2 No. 62109-1 : 2016 | SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS |
CEI EN 60216-8 : 2014 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 8: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS USING SIMPLIFIED PROCEDURES |
CEI EN 60216-4-1 : 2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 4-1: AGEING OVENS - SINGLE-CHAMBER OVENS |
I.S. EN 61730-1:2007 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
I.S. EN 60691:2016 | THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE |
I.S. EN 60216-2:2005 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
I.S. EN 60674-3-8:2011 | PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 8: BALANCED BIAXIALLY ORIENTED POLYETHYLENE NAPHTHALATE (PEN) FILMS USED FOR ELECTRICAL INSULATION |
NF EN 61857-1 : 2009 | ELECTRICAL INSULATION SYSTEMS - PROCEDURES FOR THERMAL EVALUATION - PART 1: GENERAL REQUIREMENTS - LOW-VOLTAGE |
I.S. EN 60216-4-1:2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 4-1: AGEING OVENS - SINGLE-CHAMBER OVENS |
IEC 60077-1:2017 | Railway applications - Electric equipment for rolling stock - Part 1: General service conditions and general rules |
EN 60674-3-8:2011/A1:2017 | PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 8: BALANCED BIAXIALLY ORIENTED POLYETHYLENE NAPHTHALATE (PEN) FILMS USED FOR ELECTRICAL INSULATION (IEC 60674-3-8:2011/A1:2016) |
IEC 61858:2008 | Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS |
IEC 62109-1:2010 | Safety of power converters for use in photovoltaic power systems - Part 1: General requirements |
03/314451 DC : DRAFT SEP 2003 | IEC 62392 TR ED.1 - SUITABILITY OF TYPICAL ELECTRICAL INSULATING MATERIAL FOR POLYMER RECYCLING |
IEC 62864-1:2016 | Railway applications - Rolling stock - Power supply with onboard energy storage system - Part 1: Series hybrid system |
IEC 60216-4-1:2006 | Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens |
EN 60077-1:2017 | Railway applications - Electric equipment for rolling stock - Part 1: General service conditions and general rules |
EN 61858-1:2014 | Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS |
EN 61730-1:2007/A11:2014 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2004, MODIFIED) |
EN 60216-4-1:2006 | Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens |
IEC 60077-1:2017 RLV | Railway applications - Electric equipment for rolling stock - Part 1: General service conditions and general rules |
EN 62864-1:2016 | Railway applications - Rolling stock - Power supply with onboard energy storage system - Part 1: Series hybrid system |
EN 60216-8:2013 | Electrical insulating materials - Thermal endurance properties - Part 8: Instructions for calculating thermal endurance characteristics using simplified procedures |
EN 61858:2008 | ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS |
EN 60034-18-21:2013 | Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification |
EN 61857-1:2009 | Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage |
EN 60310:2016/AC:2018-03 | RAILWAY APPLICATIONS - TRACTION TRANSFORMERS AND INDUCTORS ON BOARD ROLLING STOCK (IEC 60310:2016/COR1:2018) |
CSA E61347.1 :2003 | LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS |
CSA E61347.1 : 2003 : R2013 | LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS |
SA/SNZ TS 62446.3:2020 | Photovoltaic (PV) systems - Requirements for testing, documentation and maintenance Photovoltaic modules and plants - Outdoor infrared thermography (IEC TS 62446-3:2017, MOD) |
IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
IEC 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
IEC 60216-3:2006 | Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.