ISO 15512:2016
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Plastics Determination of water content
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Withdrawn date
02-05-2019
Superseded by
Language(s)
English, French
Published date
06-10-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1.1 ISO 15512:2016 specifies methods for the determination of the water content of plastics in the form of powder, granules, and finished articles. These methods do not test for water absorption (kinetics and equilibrium) of plastics as measured by ISO 62.
Method A is suitable for the determination of water content as low as 0,1 % with an accuracy of 0,1 %. Method B and Method C are suitable for the determination of water content as low as 0,01 % with an accuracy of 0,01 %.
Water content is an important parameter for processing materials and has to remain below the level specified in the appropriate material standard.
1.2 Four alternative methods are specified in this International Standard.
? Method A is an extraction method using anhydrous methanol followed by a Karl Fischer titration of the extracted water. It can be used for all plastics and is applicable to granules smaller than 4 mm 4 mm 3 mm. The method can also be used for, e.g. prepolymer materials in the form of a powder that are insoluble in methanol.
? Method B1 is a vaporization method using a tube oven. The water contained in the test portion is vaporized and carried to the titration cell by a dry air or nitrogen carrier gas, followed by a Karl Fischer titration of the collected water. It can be used for all plastics and is applicable to granules smaller than 4 mm 4 mm 3 mm.
? Method B2 is a vaporization method using a heated sample vial. The water contained in the test portion is vaporized and carried to the titration cell by a dry air or nitrogen carrier gas, followed by a Karl Fischer titration of the collected water. It can be used for all plastics and is applicable to granules smaller than 4 mm 4 mm 3 mm.
? Method C is a manometric method. The water content is determined from the increase in pressure, which results when the water is evaporated under a vacuum. This method is not applicable to plastic samples containing volatile compounds, other than water, in amounts contributing significantly to the vapour pressure at room temperature. Checks for the presence of large amounts of volatile compounds are to be carried out periodically, for example by gas chromatography. Such checks are particularly required for new types or grades of material.
| DevelopmentNote |
Supersedes ISO 6188 (07/2000) Supersedes ISO 960 (04/2001) DRAFT ISO/DIS 15512 is also available for this standard. (03/2018)
|
| DocumentType |
Standard
|
| Pages |
25
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 15512:2017-03 | Identical |
| NF EN ISO 15512:2017 | Identical |
| PN EN ISO 15512 : 2016 | Identical |
| NEN EN ISO 15512 : 2016 | Identical |
| NS EN ISO 15512 : 2016 | Identical |
| UNI EN ISO 15512:2017 | Identical |
| BS EN ISO 15512:2016 | Identical |
| SS-EN ISO 15512:2016 | Identical |
| DIN EN ISO 15512:2016-06 (Draft) | Identical |
| I.S. EN ISO 15512:2016 | Identical |
| SN EN ISO 15512 : 2017 | Identical |
| UNI EN ISO 15512 : 2014 | Identical |
| ONORM EN ISO 15512 : 2017 | Identical |
| UNE-EN ISO 15512:2017 | Identical |
| EN ISO 15512:2016 | Identical |
| NEN ISO 15512 : 2008 | Identical |
| BS ISO 15512 : 1999 AMD 14837 | Identical |
| NBN EN ISO 15512 : 2014 | Identical |
| UNE-EN ISO 15494:2016 | Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) - Metric series for specifications for components and the system (ISO 15494:2015) |
| BS EN ISO 16396-2:2017 | Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| I.S. EN ISO 16396-2:2017 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017) |
| 17/30349217 DC : 0 | BS EN ISO 21970-2 - PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 05/30091855 DC : DRAFT MAR 2005 | ISO 1874-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 15/30315534 DC : 0 | BS EN ISO 16396-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 18/30335365 DC : 0 | BS EN ISO 307 - PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER |
| DIN ISO 16486-1:2015-07 | Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2012 + AMD 1:2014) |
| BS ISO 12418-2:2012 | Plastics. Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates Preparation of test specimens and determination of properties |
| 01/121388 DC : DRAFT MARCH 2001 | ISO 307 PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER |
| 07/30152076 DC : 0 | BS ISO 25137-2 - PLASTICS - SULFONE PLASTICS (SP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| DIN EN 16682:2016-01 (Draft) | CONSERVATION OF CULTURAL HERITAGE - METHODS OF MEASUREMENT OF MOISTURE CONTENT, OR WATER CONTENT, IN MATERIALS CONSTITUTING IMMOVABLE CULTURAL HERITAGE |
| BS EN ISO 21809-1:2011 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Polyolefin coatings (3-layer PE and 3-layer PP) |
| ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications |
| ISO 20557-2:2018 | Plastics — Poly(phenylene ether) (PPE) moulding and extrusion materials — Part 2: Preparation of test specimen and determination of properties |
| I.S. EN ISO 20029-2:2018 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES (ISO 20029-2:2017) |
| ASTM D 6779 : 2017 : REDLINE | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| UNI EN 1555-1 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| DIN EN 13341:2011-04 | Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods (includes Amendment A1:2011) |
| DIN EN ISO 15103-2:2007-09 | PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 12201-1:2011-11 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| UNE-EN 16245-2:2014 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| BS EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) General |
| ISO 15103-2:2007 | Plastics Poly(phenylene ether) (PPE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| EN 12201-1:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| EN 13341:2005+A1:2011 | Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods |
| ONORM EN 1555-1 : 2015 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| ONORM EN 12245 : 2012 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| ONORM EN 12201-1 : 2015 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL |
| BS ISO 25137-2 : 2009 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 11/30239977 DC : 0 | BS EN 16245-2 - FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: ADDITIONAL REQUIREMENTS FOR RESINS, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| DIN EN 16245-2:2013-08 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| I.S. EN ISO 25137-2:2017 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
| BS ISO 28078-2:2009 | Plastics. Poly(phenylene sulfide) (PPS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 20029-2:2017 | Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties |
| ONORM EN ISO 307 : 2013 | PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER (ISO 307:2007 + AMD 1:2013) |
| I.S. EN ISO 307:2007 | PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER (ISO 307:2007) |
| BS EN ISO 307 : 2007 | PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER |
| ISO 28078-2:2009 | Plastics Poly(phenylene sulfide) (PPS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| UNE-EN ISO 25137-2:2017 | Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009) |
| (INACTIVE RECORD)ASTM D 5336 : 2015-04 | CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPHTHALAMIDE (PPA) INJECTION MOLDING MATERIALS |
| IEC 62899-201:2016 | Printed electronics - Part 201: Materials - Substrates |
| DIN EN ISO 1874-2:2013-03 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| DIN EN 14427:2014-09 | LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction |
| BS EN ISO 15526-2:2004 | Plastics. Polyketone (PK) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 1874-2:2012 | Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| I.S. EN ISO 15526-2:2004 | PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 15103-2:2007 | PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 12201-1:2011 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL |
| I.S. EN 1555-1:2010-2015 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| DIN EN ISO 15526-2:2004-10 | PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 1874-2:2012 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| I.S. EN 14427:2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION |
| I.S. EN 13341:2005 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| I.S. EN 12245:2009 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| NF EN 12245 : 2009 + A1 2012 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| VDI 3822 Blatt 2.1.8:2012-01 | Failure analysis - Defects of thermoplastic products made of plastics caused by weather-induced stress |
| NBR ISO 16486-1 : 2013 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 1: GENERAL |
| UNE EN ISO 307 : 2007 | PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER (ISO 307:2007/AMD 1:2013) |
| BS EN ISO 25137-2:2017 | Plastics. Sulfone polymer moulding and extrusion materials Preparation of test specimens and determination of properties |
| 15/30327856 DC : 0 | BS ISO 20558-2 - PLASTICS - POLY(PHENYLENE SULFIDE) (PPS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES |
| 13/30212494 DC : 0 | BS EN ISO 15494 - PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE) AND POLYPROPYLENE (PP) - SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM - METRIC SERIES |
| 05/30130524 DC : DRAFT MAR 2005 | ISO 22621-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 1: GENERAL |
| BS EN ISO 1133-2:2011 | Plastics. Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Method for materials sensitive to time-temperature history and/or moisture |
| 15/30304408 DC : 0 | BS EN ISO 20029-2 - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 05/30130718 DC : DRAFT MAR 2005 | EN ISO 307 - PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER |
| UNE-EN 15348:2015 | Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates |
| 09/30183439 DC : 0 | BS EN ISO 1133-2 - PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 2: METHOD FOR MATERIALS SENSITIVE TO TIME-TEMPERATURE HISTORY AND/OR MOISTURE |
| 12/30256736 DC : 0 | BS ISO 4437-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| 15/30328314 DC : 0 | BS EN ISO 20557-2 - PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES |
| 08/30191143 DC : 0 | BS EN 1555-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| 06/30146370 DC : DRAFT SEP 2006 | ISO 15439-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 4 BAR - POLYAMIDE (PA) - PART 1: GENERAL |
| BS ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels. Metric series. Specifications |
| 08/30165044 DC : DRAFT FEB 2008 | BS ISO 28078-2 - PLASTICS - POLY(PHENYLENE SULFIDE) (PPS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 4437-1:2014 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) General |
| I.S. EN ISO 15494:2015 | PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE), POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT), CROSSLINKED POLYETHYLENE (PE-X), POLYPROPYLENE (PP) - METRIC SERIES FOR SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM (ISO 15494:2015) |
| CSA B137 COMPENDIUM : 2017 | THERMOPLASTIC PRESSURE PIPING COMPENDIUM |
| ISO 20558-2:2018 | Plastics — Poly(phenylene sulfide) (PPS) moulding and extrusion materials — Part 2: Preparation of test specimen and determination of properties |
| DIN EN ISO 16396-2:2017-07 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| ISO 15494:2015 | Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) — Metric series for specifications for components and the system |
| I.S. EN 16245-2:2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| UNI EN ISO 21809-1 : 2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 1: POLYOLEFIN COATINGS (3-LAYER PE AND 3-LAYER PP) |
| ASTM D 6869 : 2017 : REDLINE | Standard Test Method for Coulometric and Volumetric Determination of Moisture in Plastics Using the Karl Fischer Reaction (the Reaction of Iodine with Water) |
| ISO 16486-1:2012 | Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing Part 1: General |
| ISO 307:2007 | Plastics Polyamides Determination of viscosity number |
| EN ISO 20029-2:2018 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties (ISO 20029-2:2017) |
| ISO 22621-1:2007 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 1: General |
| DIN EN 12245:2012-03 | Transportable gas cylinders - Fully wrapped composite cylinders (includes Amendment A1:2011) |
| DIN EN 1555-1:2010-12 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| BS EN 12201-1:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) General |
| UNE-EN ISO 1874-2:2013 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012) |
| EN 16245-2:2013 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| UNI EN ISO 1874-2 : 2013 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNI EN 13341 : 2011 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| UNI EN 16245-2 : 2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| UNI EN 14427 : 2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION |
| UNI EN 12201-1 : 2012 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL |
| UNI EN 12245 : 2011 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| UNI EN ISO 14910-2 : 2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ONORM EN 14427 : 2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION |
| DIN EN ISO 307:2013-08 | PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER (ISO 307:2007 + AMD 1:2013) |
| BS EN ISO 20029-2:2018 | Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties |
| 17/30352672 DC : 0 | BS IEC 62788-5-1 ED 1.0 - MEASUREMENT PROCEDURES FOR MATERIALS USED IN PHOTOVOLTAIC MODULES - 5-1: EDGE SEALS - SUGGESTED TEST METHODS FOR USE WITH EDGE SEAL MATERIALS |
| 11/30248330 DC : 0 | BS ISO 17467-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS JOINTED BY SOLVENT CEMENT - PART 1: GENERAL |
| BS ISO 17467-1:2012 | Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems jointed by solvent cement General |
| PREN ISO 15494 : DRAFT 2013 | PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE) AND POLYPROPYLENE (PP) - SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM - METRIC SERIES (ISO/DIS 15494:2013) |
| I.S. EN ISO 21809-1:2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 1: POLYOLEFIN COATINGS (3-LAYER PE AND 3-LAYER PP) |
| 14/30304003 DC : 0 | BS EN 62899-1 ED.1 - PRINTED ELECTRONICS - MATERIALS - PART 1: SUBSTRATES |
| BS EN 16245-2:2013 | Fibre-reinforced plastic composites. Declaration of raw material characteristics Specific requirements for resin, curing systems, additives and modifiers |
| UNI EN ISO 307 : 2013 | PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER |
| 11/30229997 DC : 0 | BS EN 14427 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION |
| BS EN 16682:2017 | Conservation of cultural heritage. Methods of measurement of moisture content, or water content, in materials constituting immovable cultural heritage |
| DIN EN 15348:2015-01 | Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates |
| BS EN ISO 15494:2015 | Plastics piping systems for industrial applications. Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP). Metric series for specifications for components and the system |
| BS EN 15348:2014 | Plastics. Recycled plastics. Characterization of poly(ethylene terephthalate) (PET) recyclates |
| I.S. EN ISO 1133-2:2011 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 2: METHOD FOR MATERIALS SENSITIVE TO TIME-TEMPERATURE HISTORY AND/OR MOISTURE (ISO 1133-2:2011) |
| UNE-EN ISO 1133-2:2012 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
| NF EN ISO 1133-2 : 2012 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 2: METHOD FOR MATERIALS SENSITIVE TO TIME-TEMPERATURE HISTORY AND/OR MOISTURE |
| DIN EN ISO 1133-2:2012-03 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
| UNE-EN ISO 21809-1:2011 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) (ISO 21809-1:2011) |
| UNE-EN ISO 16396-2:2017 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| I.S. EN ISO 14910-2:2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013, CORRECTED VERSION 2015-12-15) |
| BS IEC 62899-201 : 2016 | PRINTED ELECTRONICS - PART 201: MATERIALS - SUBSTRATES |
| ISO 12418-2:2012 | Plastics — Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates — Part 2: Preparation of test specimens and determination of properties |
| I.S. EN 16682:2017 | CONSERVATION OF CULTURAL HERITAGE - METHODS OF MEASUREMENT OF MOISTURE CONTENT, OR WATER CONTENT, IN MATERIALS CONSTITUTING IMMOVABLE CULTURAL HERITAGE |
| ISO 14910-2:2013 | Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties |
| DIN EN ISO 15494:2016-03 | PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE), POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT), CROSSLINKED POLYETHYLENE (PE-X), POLYPROPYLENE (PP) - METRIC SERIES FOR SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM (ISO 15494:2015) |
| ASTM F 3091/F3091M : 2014 | Standard Specification for Powder Bed Fusion of Plastic Materials |
| ISO 16365-2:2014 | Plastics — Thermoplastic polyurethanes for moulding and extrusion — Part 2: Preparation of test specimens and determination of properties |
| ISO 4427-1:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General |
| ISO 21809-4:2009 | Petroleum and natural gas industries External coatings for buried or submerged pipelines used in pipeline transportation systems Part 4: Polyethylene coatings (2-layer PE) |
| UNE-EN ISO 21809-1:2019 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) (ISO 21809-1:2018) |
| UNE-EN ISO 14910-2:2014 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15) |
| ISO 1133-2:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture |
| ISO 1874-2:2012 | Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| UNE-EN 1555-1:2011 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| BS EN 14427:2014 | LPG equipment and accessories. Transportable refillable fully wrapped composite cylinders for LPG. Design and construction |
| UNE-EN 14427:2014 | LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction |
| ISO 16396-2:2017 | Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 25137-2:2009 | Plastics Sulfone polymer moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| UNE-EN 12245:2009 | Transportable gas cylinders - Fully wrapped composite cylinders |
| BS EN 13341 : 2005 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| EN 14427:2014 | LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction |
| EN ISO 1874-2:2012 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012) |
| EN ISO 15526-2:2004 | Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15526-2:2000) |
| EN ISO 21809-1:2011 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) (ISO 21809-1:2011) |
| EN 16682:2017 | Conservation of cultural heritage - Methods of measurement of moisture content, or water content, in materials constituting immovable cultural heritage |
| EN ISO 16396-2:2017 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| EN 15348:2014 | Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates |
| EN ISO 15103-2:2007 | Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007) |
| EN ISO 14910-2:2013 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15) |
| EN 12245:2009+A1:2011 | Transportable gas cylinders - Fully wrapped composite cylinders |
| EN ISO 1133-2:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
| EN ISO 25137-2:2017 | Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009) |
| ISO 17467-1:2012 | Plastics piping systems for the supply of gaseous fuels Unplasticized polyamide (PA-U) piping systems jointed by solvent cement Part 1: General |
| BS ISO 16365-2:2014 | Plastics. Thermoplastic polyurethanes for moulding and extrusion Preparation of test specimens and determination of properties |
| BS ISO 21809-4:2009 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Polyethylene coatings (2-layer PE) |
| BS ISO 4427-1 : 2007 | PLASTICS PIPING SYSTEMS - POLYETHYLENE (PE) PIPES AND FITTINGS FOR WATER SUPPLY - PART 1: GENERAL |
| 08/30154948 DC : DRAFT FEB 2008 | BS ISO 21809-4 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 4: POLYETHYLENE COATINGS (2-LAYER PE) |
| 04/30126883 DC : DRAFT DEC 2004 | ISO 4437 - BURIED POLYETHYLENE (PE) PIPES FOR THE SUPPLY OF GASEOUS FUELS - METRIC SERIES - SPECIFICATIONS |
| UNI EN ISO 1133-2 : 2012 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 2: METHOD FOR MATERIALS SENSITIVE TO TIME-TEMPERATURE HISTORY AND/OR MOISTURE |
| I.S. EN 15348:2014 | PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLY(ETHYLENE TEREPHTHALATE) (PET) RECYCLATES |
| EN ISO 15494:2015 | Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) - Metric series for specifications for components and the system (ISO 15494:2015) |
| ISO 4437-1:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 1: General |
| DIN EN ISO 25137-2:2016-08 (Draft) | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
| ISO 21809-1:2011 | Petroleum and natural gas industries External coatings for buried or submerged pipelines used in pipeline transportation systems Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) |
| ISO 15439-1:2007 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) Polyamide (PA) Part 1: General |
| BS EN ISO 15103-2:2007 | Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 14910-2:2013 | Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties |
| UNE-EN 12201-1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| ISO 15526-2:2000 | Plastics Polyketone (PK) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| UNE-EN ISO 307:2007 | Plastics - Polyamides - Determination of viscosity number (ISO 307:2007) |
| DIN EN ISO 14910-2:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| ONORM EN 15348 : 2014 | PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLY(ETHYLENE TEREPHTHALATE) (PET) RECYCLATES |
| NBR 15561 : 2016 AMD 1 2017 | POLYETHYLENE PIPE PE 80 AND PE 100 FOR WATER TRANSPORT AND SEWAGE UNDER PRESSURE - REQUIREMENTS |
| ISO 1628-1:2009 | Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 1: General principles |
| ISO 1628-5:1998 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 5: Thermoplastic polyester (TP) homopolymers and copolymers |
| ISO 1628-6:1990 | Plastics — Determination of viscosity number and limiting viscosity number — Part 6: Methyl methacrylate polymers |
| ISO 1628-3:2010 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 3: Polyethylenes and polypropylenes |
| ISO 307:2007 | Plastics Polyamides Determination of viscosity number |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 1628-2:1998 | Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 2: Poly(vinyl chloride) resins |
| ISO 1628-4:1999 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 4: Polycarbonate (PC) moulding and extrusion materials |
| ISO 760:1978 | Determination of water Karl Fischer method (General method) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.